Microstructure and Mechanical Properties of AM50+xTi Magnesium Alloys Extruded from As-Cast and Solution Treated Conditions

2005 ◽  
Vol 488-489 ◽  
pp. 629-632 ◽  
Author(s):  
Qu Dong Wang ◽  
Yongjun Chen ◽  
Jianguo Peng ◽  
Man Ping Liu ◽  
Wen Jiang Ding ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Magnesium Alloys ◽  
Room Temperature ◽  
Elevated Temperatures ◽  
Solution Treatment ◽  
Solution Treated ◽  
Microstructure And Mechanical Properties ◽  
Mg17al12 Phase ◽  
Ti Addition

Microstructure and mechanical properties of AM50+xTi (x=0,0.01,0.1wt%) magnesium alloys extruded from as-cast and solution treated conditions have been studied. Results show that Ti element obviously refines the microstructure of AM50 magnesium alloy and Mg17Al12 phase. Only 0.01 wt% Ti addition can make the Mg17Al12 phase turn into particles and small rod-like shape. Ti addition improves tensile strength at room temperature, and obviously improves elongation at elevated temperatures up to 200°C. The AM50+xTi alloys extruded from as-cast have better tensile strength at room temperature and better elongation at 100°C, 150°C and 200°C than that of AM50+xTi alloys extruded from solution treatment; The plasticity of AM50 magnesium alloys increases with Ti content increasing and temperature increasing for the tensile fractograph.

Effect of Solution Treatment and Extrusion on the Microstructure and Mechanical Properties of a Mg-2Gd-Nd-0.4Zn-0.3Zr Alloy

2011 ◽  
Vol 197-198 ◽  
pp. 1125-1128 ◽  
Author(s):  
Jing Jiang Nie ◽  
Liang Meng ◽  
Xiu Rong Zhu ◽  
Yong Dong Xu ◽  
Yue Yi Wu ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Tensile Strength ◽  
Ultimate Tensile Strength ◽  
Treatment Time ◽  
Solution Treatment ◽  
Solution Treated ◽  
Microstructure And Mechanical Properties ◽  
Combined Action ◽  
Strength And Ductility

The effect of the combined action of hot work and heat treatment on the microstructure and mechanical properties of a Mg-2Gd-Nd-0.4Zn-0.3Zr (wt. %) (E21) alloy was investigated. Results showed that the solution treatment time of the ingot played a great effect on the mechanical properties of the extruded alloy. With solution treating time of the ingot increasing, the tensile strength of the extruded alloy decreased gradually, but the elongation increased greatly. The best combination of strength and ductility was achieved for the extruded alloy after the ingot solution treated at 520°C for 3 h, extrusion at 400°C and aging at 200°C for 16 h, namely ultimate tensile strength = 331MPa and elongation = 7.1%.

Effects of Sm on Microstructure and Mechanical Properties of Mg-5.5Al -0.5Y Alloy

2010 ◽  
Vol 146-147 ◽  
pp. 267-271
Author(s):  
Chang Qing Li ◽  
Quan An Li ◽  
Xing Yuan Zhang ◽  
Qing Zhang
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Elevated Temperature ◽  
Magnesium Alloy ◽  
Temperature Increase ◽  
Room Temperature ◽  
Particle Phase ◽  
Microstructure And Mechanical Properties ◽  
Mg17al12 Phase

The microstructure and mechanical properties of aged Mg-5.5Al-0.5Y magnesium alloy with Sm addition were investigated. The results show that with proper content of Sm addition, the microstructure of Mg-5.5Al-0.5Y magnesium alloy is refined obviously. The quantity of β-Mg17Al12 phase is reduced, and Al2Sm particle phase is formed. With the increase of Sm addition, the mechanical properties of the alloy at room and elevated temperature increase at first, and then decrease. When the content of Sm is up to 1%, the values of tensile strength and elongation at room temperature,150 and 175 are up to their maxima synchronously, 244MPa/20.07%, 217MPa/18.86% and 185MPa/19.15% respectively.

Effect of Zn/Er Ratio on Microstructures and Mechanical Properties of the Cast Mg-Zn-Er Alloys

2011 ◽  
Vol 686 ◽  
pp. 96-100
Author(s):  
Shu Bo Li ◽  
Han Li ◽  
Jian Hui Li ◽  
Wen Bo Du ◽  
Zhao Hui Wang
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Ultimate Tensile Strength ◽  
Magnesium Alloys ◽  
Room Temperature ◽  
Secondary Phase ◽  
Alloying Elements ◽  
Quasicrystalline Phase ◽  
Microstructure And Mechanical Properties ◽  
Microstructures And Mechanical Properties

The microstructures and mechanical properties of the Mg-Zn-Er alloys have been investigated. The results show that the alloying elements (Zn/Er) with different ratio have a great effect on the microstructure and mechanical properties of the magnesium alloys, especially for the phase constitutes. Furthermore, the more attractive result is that the quasicrystalline phase, as the main secondary phase, precipitates during solidification in the alloy with addition of Zn/Er ration of 6. The cast Mg-5Zn-0.83Er alloy exhibits the ultimate tensile strength and yield tensile strength are 190MPa and 80MPa at room temperature, respectively, with an elongation of 15%.

Microstructures and Mechanical Properties of AJ62 Magnesium Alloy with Y and Nd Elements

2011 ◽  
Vol 686 ◽  
pp. 253-259
Author(s):  
Xu Ning ◽  
Wei Dong Xie ◽  
Chun Mei Dang ◽  
Xiao Dong Peng ◽  
Yan Yang ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Solid Solution ◽  
Tensile Strength ◽  
Rare Earth ◽  
Magnesium Alloy ◽  
Room Temperature ◽  
Solution Treatment ◽  
Solid Solution Treatment ◽  
Microstructure And Mechanical Properties ◽  
Microstructures And Mechanical Properties

A series of Mg-6Al-2Sr-1.5Y-xNd (x=0, 0.3, 0.6, 0.9, 1.2) alloy samples were prepared and their microstructures were observed and mechanical properties were measured. The existing forms of Y and Nd were studied. The effects of Y and Nd on microstructure and mechanical properties of AJ62 alloy were investigated. The results show that the main existing forms of Y and Nd in AJ62 alloy are Al2Y and Al2Nd. The combined addition of rare earth Y and Nd can refine α-Mg matrix obviously and reduce the amount of the β-Mg17Al12phases; after solid solution treatment, the tensile strength of the alloys rise first and fall later with increasing content of Nd. When the content of Nd is about 0.6%wt, the values of tensile strengthes are up to the maximum both at room temperature and at 448 K.

The Study on Microstructures and Mechanical Properties of Heat Rolled and Solution-Treated Fe-26Mn-6Al-1C Steel

2012 ◽  
Vol 482-484 ◽  
pp. 1530-1533
Author(s):  
Ming Li Huang ◽  
Hua Ying Li ◽  
Hua Ding
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Ultimate Tensile Strength ◽  
Yield Strength ◽  
Room Temperature ◽  
Solution Treatment ◽  
Tensile Tests ◽  
Solution Treated ◽  
Sem And Tem ◽  
Hot Rolled

In the present work, mechanical properties and microstructures of hot-rolled and solution-treated Fe-26Mn-6Al-1C steel (6Al steel) were investigated. Tensile tests were carried out at room temperature. The samples were characterized by using XRD, OM, SEM and TEM. The results suggested that the microstructure of the hot rolled 6Al steel was fully austenitic. After solution treatment and deformation, the microstructure was still single austenite. With the increase of the solution treatment temperatures, the strength decreased and the elongation increased. After solution treated at 1100°C for 1h, the yield strength, ultimate tensile strength and elongation were 378MPa, 756MPa and 57%.

Effect of Deformation Ratios on Microstructure and Mechanical Properties of ZK60 Magnesium Alloy by Hydrostatic Extruded at Room Temperature

2012 ◽  
Vol 557-559 ◽  
pp. 13-17
Author(s):  
Rong Wang ◽  
Xiu Rong Zhu ◽  
Gang Chen ◽  
Jing Jiang Nie ◽  
Yong Dong Xu ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Magnesium Alloy ◽  
Magnesium Alloys ◽  
Deformation Mechanism ◽  
Room Temperature ◽  
Elongation Rate ◽  
Microstructure And Mechanical Properties ◽  
Deformation Ratio ◽  
Zk60 Magnesium Alloy

The effect of different hydrostatic extrusion ratios on the microstructure and mechanical properties of the ZK60 magnesium alloys were investigated. The results showed that, the major deformation mechanism of the alloy is twinning at room temperature, which resulted in that the tensile strengthen and hardness of the extruded alloy improved greatly. With deformation ratio increasing, the ultimate tensile strengthen and hardness are linearly increased, with the functions of Y= 4.2X+358.3 and Y=2.3X +73.69, respectively. And the maximum tensile strength and hardness of the extruded alloy are 383 MPa and 87HB, respectively. But the elongation decreases obviously, the minimum decreasing degree is 50%. With the deformation ratio increasing, the tendency of elongation rate increased as an “M” model.

scholarly journals Effects of Gd, Y Content on the Microstructure and Mechanical Properties of Mg-Gd-Y-Nd-Zr Alloy

Metals ◽  
2018 ◽  
Vol 8 (10) ◽  
pp. 790 ◽  
Author(s):  
Changping Tang ◽  
Kai Wu ◽  
Wenhui Liu ◽  
Di Feng ◽  
Xuezhao Wang ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Ultimate Tensile Strength ◽  
Solution Treatment ◽  
Age Hardening ◽  
Uniaxial Tensile ◽  
Microstructure And Mechanical Properties ◽  
Shaped Particle ◽  
Zr Alloy ◽  
Non Equilibrium

The effects of Gd, Y content on the microstructure and mechanical properties of Mg-Gd-Y-Nd-Zr alloy were investigated using hardness measurements, X-ray diffraction (XRD), scanning electron microscopy (SEM), energy dispersive spectrometer (EDS), and uniaxial tensile testing. The results indicate that the alloys in as-cast condition mainly consist of α-Mg matrix and non-equilibrium eutectic Mg5.05RE (RE = Gd, Y, Nd). After solution treatment, the non-equilibrium eutectics dissolved into the matrix but some block shaped RE-rich particles were left at the grain boundaries and within grains. These particles are especially Y-rich and deteriorate the mechanical properties of the alloys. Both the compositions of the eutectic and the block shaped particle were independent of the total Gd, Y content of the alloys, but the number of the particles increases as the total Gd, Y content increases. The ultimate tensile strength increases as the total Gd, Y content decreases. A Mg-5.56Gd-3.38Y-1.11Nd-0.48Zr alloy with the highest ultimate tensile strength of 280 MPa and an elongation of 1.3% was fabricated. The high strength is attributed to the age hardening behavior and the decrease in block shaped particles.

Strength of Commercial Aluminum Alloys after Equal Channel Angular Pressing and Post-ECAP Processing

2006 ◽  
Vol 114 ◽  
pp. 91-96 ◽  
Author(s):  
Maxim Yu. Murashkin ◽  
M.V. Markushev ◽  
Julia Ivanisenko ◽  
Ruslan Valiev
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Tensile Strength ◽  
Aluminum Alloys ◽  
Ultimate Tensile Strength ◽  
Equal Channel Angular Pressing ◽  
Room Temperature ◽  
Solution Treatment ◽  
Ecap Processing ◽  
Angular Pressing

The effects of equal channel angular pressing (ECAP), further heat treatment and rolling on the structure and room temperature mechanical properties of the commercial aluminum alloys 6061 (Al-0.9Mg-0.7Si) and 1560 (Al-6.5Mg-0.6Mn) were investigated. It has been shown that the strength of the alloys after ECAP is higher than that achieved after conventional processing. Prior ECAP solution treatment and post-ECAP ageing can additionally increase the strength of the 6061 alloy. Under optimal ageing conditions a yield strength (YS) of 434 MPa and am ultimate tensile strength (UTS) of 470 MPa were obtained for the alloy. Additional cold rolling leads to a YS and UTS of 475 and 500 MPa with 8% elongation. It was found that the post-ECAP isothermal rolling of the 1560 alloy resulted in the formation of a nano-fibred structure and a tensile strength (YS = 540 MPa and UTS = 635 MPa) that has never previously been observed in commercial non-heat treatable alloys.

Effect of Mg and Cu Additions on Microstructure and Mechanical Properties of Squeeze Casting Al-Si-Cu-Mg Alloy

2016 ◽  
Vol 850 ◽  
pp. 511-518 ◽  
Author(s):  
Hai Jun Liu ◽  
Lie Jun Li ◽  
Jian Wei Niu ◽  
Ji Xiang Gao ◽  
Chuan Dong Ren
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Artificial Aging ◽  
Squeeze Casting ◽  
Solution Treatment ◽  
Mg Alloys ◽  
Percentage Elongation ◽  
Microstructure And Mechanical Properties ◽  
Content Ratio ◽  
Cast Alloys

The effects of Mg and Cu additions with different contents on the mechanical properties of Al-Si alloy prepared by indirect squeeze casting have been experimentally investigated. The microstructure and mechanical properties of as-cast and T6-treated Al-Si-Cu-Mg alloys were tested by OM, SEM, DSC and tensile measurement, where the samples were produced by artificial aging at 180°C for 8 h after solution treatment at 540°C for 4 h. It has been found that for the as-cast alloys, with increasing contents of Mg and Cu the tensile strength (UTS) and yield strength (YS) increased, while the percentage elongation (El) decreased. And the optimal mechanical properties of Al-Si-Cu-Mg alloys were obtained under the content ratio of Cu/Mg within 4, where the UTS and El reached 426 MPa and 6.3% after T6 treated, respectively.

Effect of Solution Temperature on the Microstructure and Mechanical Properties of Wrought 316LN Stainless Steel

2014 ◽  
Vol 915-916 ◽  
pp. 576-582 ◽  
Author(s):  
H. C. Wu ◽  
B. Yang ◽  
Ming Xian Zhang ◽  
Sheng Long Wang ◽  
Y. Z. Shi
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Stainless Steel ◽  
Solution Treatment ◽  
Solution Temperature ◽  
Tensile Fracture ◽  
316Ln Stainless Steel ◽  
Microstructure And Mechanical Properties ◽  
Average Grain Size ◽  
Fracture Morphologies

The effect of forging and solution temperature on the microstructure and mechanical properties of 316LN stainless steel has been investigated by optical microscope, tensile testing machine and scanning electron microscope (SEM). The results show that the average grain size of the steel was refined from 150μm to 70μm after forging and solution treatment. With increasing solution temperature, the tensile strength and yield strength decreased. On the contrary, the elongation of the steel increased with increasing solution temperature except at 1200°C. The tensile strength of the samples forged at 1100°C is better than those of the samples forged at 1000 and 1200°Cafter solution treatment. Tensile fracture morphologies observation showed that all the specimens have ductile fracture morphologies. With increasing solution temperature, the toughness of the steel becomes better and better except at 1200°C. Both the microstructure and mechanical properties of the 316LN stainless steel have been improved after forging at 1100°C and following by solution treatment at 1150°C.

Sign in / Sign up

Export Citation Format

Share Document