Cutting Force Experiment and Simulation by Hard Turning GCr15 Bearing Steel with High Speed Considering Cutting Edge Preparation

2006 ◽  
Vol 532-533 ◽  
pp. 845-848
Author(s):  
Yu Wang ◽  
Fu Gang Yan ◽  
Jing Shu Hu ◽  
Tao Chen ◽  
Zhen Chang ◽  
...  
Keyword(s):  
Surface Roughness ◽  
Finite Element ◽  
Cutting Forces ◽  
High Speed ◽  
Hard Turning ◽  
Cutting Speed ◽  
Bearing Steel ◽  
Machined Surface ◽  
Element Analysis ◽  
Gcr15 Bearing Steel

In this study, hard turning GCr15 bearing steel with high cutting speed is experimental investigated the influence of the CB7015WH insert with chamfer edge and Safe-Lock and the CB7015 insert with a combination of hone radius and a chamfer edge on cutting forces and surface roughness of machined surface. Experimental results show that the cutting forces of the chamfer edge and Safe-Lock is smaller than that of the combination of hone radius and a chamfer edge. Moreover, surface roughness of machined surface with the CB7015WH insert is better. A coupled thermo-mechanical 2D finite element model with general finite element analysis software Deform 2D.8.1 is developed for the influence of two kinds of inserts on cutting forces and effective stress. The simulation results are compared with experimental data and found to be in good agreement.

Effect of High Speed Dry End Milling on Surface Roughness and Cutting Forces of Ti-6Al-4V ELI

2014 ◽  
Vol 493 ◽  
pp. 546-551 ◽  
Author(s):  
Safian Sharif ◽  
Habib Safari ◽  
Sudin Izman ◽  
Denni Kurniawan
Keyword(s):  
Surface Roughness ◽  
Surface Quality ◽  
Cutting Forces ◽  
High Speed ◽  
End Milling ◽  
Cutting Speed ◽  
Machined Surface ◽  
Milled Surface ◽  
Cemented Carbide Tools ◽  
Cutting Speeds

The surface quality generated when high speed dry end milling (HSDEM) Ti-6Al-4V-ELI titanium alloy with coated and uncoated carbide tools were investigated. Evaluation was conducted using TiAlN+TiN coated and uncoated cemented carbide tools under different high cutting speeds and feed rates conditions. Surface roughness and cutting forces were measured when using new tools. The milled surface quality and corresponding alteration were characterized through electron microscopy. Within the investigated conditions high quality surface finish was obtained on the machined surface. Increasing cutting speed from 200 to 300 m/min during the process improved the surface finished particularly under lower feed rates. In term of generated surface quality, uncoated H25 grade carbide tools out performed coated F40M grade specifically at the higher cutting conditions. The main damages observed after HSDEM on the surface for all machining conditions contain redeposited materials, feed marks, and tool edge marks. Under both tested feed rates the resultant cutting force decreased by increasing the cutting speeds and uncoated carbide tools provide the lower cutting forces compared to coated types.

Machining Evaluation of High-Speed Milling for Thin-Wall Machining of Al7075-T651

2014 ◽  
Vol 541-542 ◽  
pp. 785-791 ◽  
Author(s):  
Joon Young Koo ◽  
Pyeong Ho Kim ◽  
Moon Ho Cho ◽  
Hyuk Kim ◽  
Jeong Kyu Oh ◽  
...  
Keyword(s):  
Surface Roughness ◽  
Surface Integrity ◽  
Cutting Forces ◽  
High Speed ◽  
Surface Condition ◽  
Cutting Conditions ◽  
Depth Of Cut ◽  
Thin Wall ◽  
Machined Surface ◽  
High Speed Milling

This paper presents finite element method (FEM) and experimental analysis on high-speed milling for thin-wall machining of Al7075-T651. Changes in cutting forces, temperature, and chip morphology according to cutting conditions are analyzed using FEM. Results of machining experiments are analyzed in terms of cutting forces and surface integrity such as surface roughness and surface condition. Variables of cutting conditions are feed per tooth, spindle speed, and axial depth of cut. Cutting conditions to improve surface integrity were investigated by analysis on cutting forces and surface roughness, and machined surface condition.

Analysis of Cutting Parameters Influence on the Machined Surface Roughness Obtained by Turning of a Heat Treated Bearing Steel

2015 ◽  
Vol 809-810 ◽  
pp. 195-200
Author(s):  
Constatin Rotariu ◽  
Sevasti Mitsi ◽  
Dragos Paraschiv ◽  
Octavian Lupescu ◽  
Sergiu Lungu ◽  
...  
Keyword(s):  
Heat Treatment ◽  
Surface Roughness ◽  
Hard Turning ◽  
Cutting Parameters ◽  
Bearing Steel ◽  
Machined Surface ◽  
Heat Treated ◽  
Machined Surface Roughness ◽  
Bearing Rings ◽  
Quality Surface

In this paper we analyze the influence of cutting parameters on the surface quality, surface roughness respectively, processed by turning when heat treated bearing steel, also called hard turning, and processing by turning of bearing steel without heat treatment. We set parameters of the cutting regime influencing the achievement of roughness surfaces which must be within the predetermined requirements if bearing rings exceeding 500 mm in diameter. This analysis will be done by statistical methods using the software Minitab 14.

Cutting Forces and Surface Roughness in High-Speed End Milling of Ti6Al4V

2013 ◽  
Vol 589-590 ◽  
pp. 76-81
Author(s):  
Fu Zeng Wang ◽  
Jun Zhao ◽  
An Hai Li ◽  
Jia Bang Zhao
Keyword(s):  
Surface Roughness ◽  
Surface Quality ◽  
Cutting Forces ◽  
High Speed ◽  
End Milling ◽  
Cutting Speed ◽  
Depth Of Cut ◽  
Wide Range ◽  
Radial Depth ◽  
Coated Carbide

In this paper, high speed milling experiments on Ti6Al4V were conducted with coated carbide inserts under a wide range of cutting conditions. The effects of cutting speed, feed rate and radial depth of cut on the cutting forces, chip morphologies as well as surface roughness were investigated. The results indicated that the cutting speed 200m/min could be considered as a critical value at which both relatively low cutting forces and good surface quality can be obtained at the same time. When the cutting speed exceeds 200m/min, the cutting forces increase rapidly and the surface quality degrades. There exist obvious correlations between cutting forces and surface roughness.

Investigation of Surface Characteristics and Chip Morphology in High Speed Cutting of Inconel718 Based on SHPB System

2019 ◽  
Author(s):  
Zengqiang Wang ◽  
Zhanfei Zhang ◽  
Wenhu Wang ◽  
Ruisong Jiang ◽  
Kunyang Lin ◽  
...  
Keyword(s):  
Surface Roughness ◽  
High Speed ◽  
Split Hopkinson Pressure Bar ◽  
Orthogonal Cutting ◽  
Cutting Speed ◽  
Surface Profile ◽  
Chip Morphology ◽  
Depth Of Cut ◽  
Machined Surface ◽  
High Speed Cutting

Abstract High speed cutting (HSC) technology has the characteristics of high material removal rates and high machining precision. In order to study the relationships between chip morphology and machining surface characteristic in high speed cutting of superalloy Inconel718. High-speed orthogonal cutting experiment are carried out by used a high speed cutting device based on split Hopkinson pressure bar (SHPB). The specimen surfaces and collected chips were then detected with optical microscope, scanning electron microscope and three-dimensional surface profile measuring instrument. The results show that within the experimental parameters (cutting speed from 8–16m/s, depth of cut 0.1–0.5mm), the obtained chips are sawtooth chips and periodic micro-ripple appear on the machined surface. With the cutting speed increases, machining surface roughness is decreases from 1.4 to 0.99μm, and the amplitude of periodic ripples also decreases. With the cutting depth increases, the machining surface roughness increases from 0.96 to 5.12μm and surface topography becomes worse. With the increase of cutting speed and depth of cut, the chips are transform from continues sawtooth to sawtooth fragment. By comparing the frequency of surface ripples and sawtooth chips, it is found that they are highly consistent.

Effect of Machining Parameters and MQL Liquids on Surface Integrity of High Speed Drilling Ti-6Al-4V

2010 ◽  
Vol 447-448 ◽  
pp. 816-820 ◽  
Author(s):  
Erween Abdul Rahim ◽  
Hiroyuki Sasahara
Keyword(s):  
Surface Roughness ◽  
Palm Oil ◽  
Surface Integrity ◽  
High Speed ◽  
Cutting Speed ◽  
Machining Parameters ◽  
Machined Surface ◽  
Subsurface Deformation ◽  
High Speed Drilling ◽  
Coated Carbide

Surface integrity is particularly important for the aerospace industry components in order to permit longer service life and maximized its reliability. This present work compares the performance of palm oil and synthetic ester on surface roughness, surface defect, microhardness and subsurface deformation when high speed drilling of Ti-6Al-4V under MQL condition. The drilling tests were conducted with AlTiN coated carbide tool. The surface roughness decreased with increasing in cutting speed and thicker subsurface deformation was formed underneath the machined surface. Grooves, cavities, pit holes, microcracks and material smearing were the dominant surface damages thus deteriorated the machined surface. For both lubricants, the machined surface experienced from thermal softening and work hardening effect thus gave a variation in microhardness values. The results indicated the substantial benefit of MQL by palm oil on surface integrity.

Study on Residual Stress for High-Speed Cutting Titanium Alloy Based on Finite Element Method

2011 ◽  
Vol 188 ◽  
pp. 216-219 ◽  
Author(s):  
M.H. Wang ◽  
Zhong Hai Liu ◽  
Hu Jun Wang
Keyword(s):  
Residual Stress ◽  
Finite Element ◽  
Titanium Alloy ◽  
High Speed ◽  
Cutting Speed ◽  
Simulation Method ◽  
Residual Tensile Stress ◽  
Cutting Depth ◽  
Machined Surface ◽  
High Speed Cutting

In order to improve machined surface quality and reduce the deformation, the residual stress involved in cutting titanium alloy was studied under different cutting speed and cutting depth by finite element simulation method. The results indicate that the increase of cutting speed and cutting depth are helpful to the surface residual compressive stress generating. However the increase of cutting speed also leads to the increase of surface residual tensile stress, the effect degree is relatively small. It is required to select higher cutting speed and smaller cutting depth to improve the surface stress state and reduce the unexpected distortion.

3D Finite Element Analysis of Prestressed Cutting

2012 ◽  
Vol 591-593 ◽  
pp. 766-770 ◽  
Author(s):  
Rui Tao Peng ◽  
Fang Lu ◽  
Xin Zi Tang ◽  
Yuan Qiang Tan
Keyword(s):  
Residual Stress ◽  
Finite Element ◽  
Three Dimensional ◽  
Element Model ◽  
Bearing Steel ◽  
Arbitrary Lagrangian Eulerian ◽  
Machined Surface ◽  
Element Analysis ◽  
Simulation Techniques ◽  
Ale Formulation

In order to reveal the adjustment principle of prestressed cutting on the residual stress of hardened bearing steel GCr15, a three-dimensional thermal elastic-viscoplastic finite element model was developed using an Arbitrary Lagrangian Eulerian (ALE) formulation. Several key simulation techniques including the material constitutive model, constitutive damage law and contact with friction were discussed, simulation of chip formation during prestressed cutting was successfully conducted. At the prestresses of 0 MPa, 341 MPa and 568 MPa, distributions of residual stress on machined surface were simulated and experimentally verified. The results indicated that residual compressive stress on machined surface were achieved and actively adjusted by utilizing the prestressed cutting method; meanwhile, within the elastic limit of bearing steel material, the higher applied prestress leads to the more prominent compressive residual stress in the surface layer and subsequently the higher fatigue resistance of the part.

Sign in / Sign up

Export Citation Format

Share Document