Microstructural Evolution in the Processing of Bulk Samples Using High-Pressure Torsion

2007 ◽  
Vol 539-543 ◽  
pp. 80-85
Author(s):  
Z. Horita ◽  
Terence G. Langdon
Keyword(s):  
Plastic Deformation ◽  
High Pressure ◽  
Severe Plastic Deformation ◽  
Room Temperature ◽  
High Pressure Torsion ◽  
Central Zone ◽  
Thin Disk ◽  
Metallic Materials ◽  
Microstructural Refinement ◽  
Established Technique

Although high-pressure torsion (HPT) is now a well-established technique for imposing severe plastic deformation on metallic materials, the technique is generally restricted to use with thin disk samples. This paper describes experiments which were conducted to evaluate the potential for making use of HPT with bulk samples in the form of small cylinders. The experiments were performed using an Al-Mg-Sc alloy and the samples were strained under a pressure of 1 GPa at room temperature. The results demonstrate excellent microstructural refinement in the vicinity of the central zone around the periphery of the cylinders.

GRAIN REFINEMENT AND MICROSTRUCTURE EVOLUTION IN ALUMINUM A2618 ALLOY BY HIGH-PRESSURE TORSION

2016 ◽  
Vol 78 (6-9) ◽  
Author(s):  
Intan Fadhlina Mohamed ◽  
Seungwon Lee ◽  
Kaveh Edalati ◽  
Zenji Horita ◽  
Shahrum Abdullah ◽  
...  
Keyword(s):  
Plastic Deformation ◽  
High Pressure ◽  
Grain Refinement ◽  
Room Temperature ◽  
Rotation Speed ◽  
High Pressure Torsion ◽  
Applied Pressure ◽  
Saturation Level ◽  
Microstructural Refinement ◽  
Average Grain Size

This work presents a study related to the grain refinement of an aluminum A2618 alloy achieved by High-Pressure Torsion (HPT) known as a process of Severe Plastic Deformation (SPD). The HPT is conducted on disks of the alloy under an applied pressure of 6 GPa for 1 and 5 turns with a rotation speed of 1 rpm at room temperature. The HPT processing leads to microstructural refinement with an average grain size of ~250 nm at a saturation level after 5 turns. Gradual increases in hardness are observed from the beginning of straining up to a saturation level. This study thus suggests that hardening due to grain refinement is attained by the HPT processing of the A2618 alloy at room temperature.

Processing Different Magnesium Alloys through HPT

2014 ◽  
Vol 783-786 ◽  
pp. 2617-2622 ◽  
Author(s):  
Livia Raquel C. Malheiros ◽  
Roberto B. Figueiredo ◽  
Terence G. Langdon
Keyword(s):  
Plastic Deformation ◽  
High Pressure ◽  
Magnesium Alloys ◽  
Room Temperature ◽  
High Pressure Torsion ◽  
Structure Refinement ◽  
Hardness Distribution ◽  
Metallic Materials ◽  
Processing Conditions ◽  
Significant Structure

High-Pressure Torsion (HPT) is widely used to refine the structure of metallic materials through the use of severe plastic deformation. This technique is used in this report to process different magnesium alloys using various processing conditions. The high hydrostatic pressure allows processing of these materials at room temperature without cracking. The structure was characterized and hardness distribution was determined at different areas of the processed samples. The results show significant structure refinement and increased hardness. The evolution of the structure and hardness depends on the alloying and HPT processing conditions.

Submicrocrystalline Austenitic Stainless Steel Processed by Cold or Warm High Pressure Torsion

2016 ◽  
Vol 838-839 ◽  
pp. 398-403 ◽  
Author(s):  
Marina Tikhonova ◽  
Nariman Enikeev ◽  
Ruslan Z. Valiev ◽  
Andrey Belyakov ◽  
Rustam Kaibyshev
Keyword(s):  
Plastic Deformation ◽  
High Pressure ◽  
Stainless Steel ◽  
Austenitic Stainless Steel ◽  
Severe Plastic Deformation ◽  
Room Temperature ◽  
High Pressure Torsion ◽  
Submicrocrystalline Structure ◽  
Ultrafine Grained ◽  
Different Temperatures

The formation of submicrocrystalline structure during severe plastic deformation and its effect on mechanical properties of an S304H austenitic stainless steel with chemical composition of Fe – 0.1C – 0.12N – 0.1Si – 0.95Mn – 18.4Cr – 7.85Ni – 3.2Cu – 0.5Nb – 0.01P – 0.006S (all in mass%) were studied. The severe plastic deformation was carried out by high pressure torsion (HPT) at two different temperatures, i.e., room temperature or 400°C. HPT at room temperature or 400°C led to the formation of a fully austenitic submicrocrystalline structure. The grain size and strength of the steels with ultrafine-grained structures produced by cold or warm HPT were almost the same. The ultimate tensile strengths were 1950 MPa and 1828 MPa after HPT at room temperature and 400°C, respectively.

Application of High Pressure Torsion to Bulk Samples

2006 ◽  
Vol 503-504 ◽  
pp. 391-398 ◽  
Author(s):  
Genki Sakai ◽  
Katsuaki Nakamura ◽  
Z. Horita ◽  
Terence G. Langdon
Keyword(s):  
High Pressure ◽  
Tensile Testing ◽  
Room Temperature ◽  
High Pressure Torsion ◽  
Initial Strain Rate ◽  
Thin Disk ◽  
Metallic Materials ◽  
Grain Sizes ◽  
Angular Pressing ◽  
Cylindrical Samples

High pressure torsion (HPT) is a well-known procedure to impart severe plastic deformation (SPD) into metallic materials. It was reported that HPT produces grain sizes finer than those using other SPD processes such as equal-channel angular pressing (ECAP). However, the application of HPT has been restricted to thin disk samples. In this study, an HPT process was developed for use with bulk samples. This process is designated as Bulk-HPT for comparison with conventional Disk-HPT. Cylindrical samples of an Al-3%Mg-0.2%Sc alloy having dimensions of 10 mm in diameter and 8.6 mm in height were prepared for Bulk-HPT. The samples were strained under a pressure of 1 GPa for 2 turns at room temperature. Microstructural observations revealed that the samples contained regions having a grain size of ~130 nm. Tensile testing showed a superplastic ductility ~480 % at 673 K with an initial strain rate of 3.3x10-2 s-1.

The Processing of Ultrafine-Grained Materials Using High-Pressure Torsion

2007 ◽  
Vol 558-559 ◽  
pp. 1283-1294 ◽  
Author(s):  
Cheng Xu ◽  
Z. Horita ◽  
Terence G. Langdon
Keyword(s):  
Plastic Deformation ◽  
Grain Size ◽  
High Pressure ◽  
High Pressure Torsion ◽  
Metallic Materials ◽  
Grain Sizes ◽  
Ultrafine Grained ◽  
Wide Range ◽  
Ultrafine Grained Materials ◽  
Thin Disks

It is now well-established that processing through the application of severe plastic deformation (SPD) leads to a significant reduction in the grain size of a wide range of metallic materials. This paper examines the fabrication of ultrafine-grained materials using high-pressure torsion (HPT) where this process is attractive because it leads to exceptional grain refinement with grain sizes that often lie in the nanometer or submicrometer ranges. Two aspects of HPT are examined. First, processing by HPT is usually confined to samples in the form of very thin disks but recent experiments demonstrate the potential for extending HPT also to bulk samples. Second, since the strains imposed in HPT vary with the distance from the center of the disk, it is important to examine the development of inhomogeneities in disk samples processed by HPT.

scholarly journals The Effect of the In-Situ Heat Treatment on the Martensitic Transformation and Specific Properties of the Fe-Mn-Si-Cr Shape Memory Alloys Processed by HSHPT Severe Plastic Deformation

Materials ◽  
2021 ◽  
Vol 14 (16) ◽  
pp. 4621
Author(s):  
Carmela Gurau ◽  
Gheorghe Gurau ◽  
Felicia Tolea ◽  
Bogdan Popescu ◽  
Mihaela Banu ◽  
...  
Keyword(s):  
Plastic Deformation ◽  
High Pressure ◽  
Severe Plastic Deformation ◽  
High Speed ◽  
High Pressure Torsion ◽  
Electron Interaction ◽  
Sudden Increase ◽  
Neel Temperature ◽  
Néel Temperature

This work focuses on the temperature evolution of the martensitic phase ε (hexagonal close packed) induced by the severe plastic deformation via High Speed High Pressure Torsion method in Fe57Mn27Si11Cr5 (at %) alloy. The iron rich alloy crystalline structure, magnetic and transport properties were investigated on samples subjected to room temperature High Speed High Pressure Torsion incorporating 1.86 degree of deformation and also hot-compression. Thermo-resistivity as well as thermomagnetic measurements indicate an antiferromagnetic behavior with the Néel temperature (TN) around 244 K, directly related to the austenitic γ-phase. The sudden increase of the resistivity on cooling below the Néel temperature can be explained by an increased phonon-electron interaction. In-situ magnetic and electric transport measurements up to 900 K are equivalent to thermal treatments and lead to the appearance of the bcc-ferrite-like type phase, to the detriment of the ε(hcp) martensite and the γ (fcc) austenite phases.

Structure and Properties of Grain Boundaries in Submicrocrystalline W Obtained by Severe Plastic Deformation

2009 ◽  
Vol 283-286 ◽  
pp. 629-638 ◽  
Author(s):  
Vladimir V. Popov ◽  
Ruslan Valiev ◽  
E.N. Popova ◽  
A.V. Sergeev ◽  
A.V. Stolbovsky ◽  
...  
Keyword(s):  
Thermal Stability ◽  
Plastic Deformation ◽  
High Pressure ◽  
Severe Plastic Deformation ◽  
Grain Boundaries ◽  
High Pressure Torsion ◽  
Submicrocrystalline Structure ◽  
Emission Mössbauer Spectroscopy ◽  
Structure And Properties ◽  
Initial State

Submicrocrystalline structure of W obtained by severe plastic deformation (SPD) by high pressure torsion (5 revolutions of anvils at 4000C) and its thermal stability have been examined by TEM. Grain boundaries of submicrocrystalline W have been studied by the method of the emission Mössbauer spectroscopy in the initial state and after annealing at 400-6000С.

Reversible Martensitic Transformation Produced by Severe Plastic Deformation of Metastable Austenitic Steel

2013 ◽  
Vol 738-739 ◽  
pp. 491-495 ◽  
Author(s):  
Igor Litovchenko ◽  
Alexander Tyumentsev ◽  
Alexander V. Korznikov
Keyword(s):  
Plastic Deformation ◽  
High Pressure ◽  
Martensitic Transformation ◽  
Severe Plastic Deformation ◽  
Dynamic Recrystallization ◽  
Austenitic Steel ◽  
High Pressure Torsion ◽  
Martensitic Transformations ◽  
Metastable Austenitic Steel ◽  
Nanostructured States

The peculiarities of martensitic transformations and formation of nanostructured states in metastable austenitic steel (Fe-18Cr-8Ni-Ti) after severe plastic deformation by high pressure torsion are investigated. It is shown that during severe plastic deformation with increased strain rate not only direct (γ→α΄) but also reverse (α΄→γ) martensitic transformations occur, which is revealed by the changes in the volume content of α΄ - martensite during deformation. The fragments thought to be formed by direct and reverse martensitic transformations and those of dynamic recrystallization of austenite are observed.

Mechanism of activation of TiFe intermetallics for hydrogen storage by severe plastic deformation using high-pressure torsion

2013 ◽  
Vol 103 (14) ◽  
pp. 143902 ◽  
Author(s):  
Kaveh Edalati ◽  
Junko Matsuda ◽  
Makoto Arita ◽  
Takeshi Daio ◽  
Etsuo Akiba ◽  
...  
Keyword(s):  
Plastic Deformation ◽  
High Pressure ◽  
Severe Plastic Deformation ◽  
Hydrogen Storage ◽  
High Pressure Torsion
Sign in / Sign up

Export Citation Format

Share Document