Microstructure and Magnetic Properties of Undercooled Fe-80at%Ni Alloys

2009 ◽  
Vol 620-622 ◽  
pp. 327-330
Author(s):  
Hui Xie ◽  
G.H. Bai ◽  
L. Jia ◽  
E.K. Liu ◽  
Zhen Lin Lu
Keyword(s):  
Grain Size ◽  
Magnetic Properties ◽  
Xrd Analysis ◽  
Optical Microscope ◽  
X Ray Diffraction ◽  
Soft Magnetic ◽  
Grain Coarsening ◽  
Ni Alloys ◽  
Purification Technique ◽  
Maximum Undercooling

Bulk Fe-80at%Ni melts were undercooled by using cyclic superheating and glass slag purification technique, and the maximum undercooling 340 K could be achieved. The microstructures of Fe-80at%Ni alloys were observed by means of optical microscope (OM). The phase composition was identified by X-ray diffraction (XRD) analysis. The magnetic properties of Fe-80at%Ni alloys were measured by vibrating sample magnetometer (VSM) with a DC M-H analyzer. The results showed that there was only single γ-(Fe, Ni) phase existing in undercooled Fe-80at%Ni alloys. Two grain refinements and one grain coarsening were observed in the undercooling range from 28 K to 340 K. The first grain refinement could be ascribed to dendrite-remelting, and the second to recrystallization induced by the stress originating from rapid solidification. The grain coarsening could be considered as a result of solid-state grain coalescence. The measurement of soft magnetic properties showed that the grain size D decreases with an increase of undercooling, the maximum Ms is 109.98emu/g, corresponding to minimum grain size 42.9μm or undercooling 210 K, and the coercive force Hc is in proportion to the reciprocal of grain size D-1.

Microstructure and Magnetic Properties of CoFeHfO Rich Nanocrystalline Thin Films Application for High Frequency

2007 ◽  
Vol 558-559 ◽  
pp. 975-978
Author(s):  
L.V. Tho ◽  
K.E. Lee ◽  
Cheol Gi Kim ◽  
Chong Oh Kim ◽  
W.S. Cho
Keyword(s):  
Thin Film ◽  
Thin Films ◽  
Magnetic Properties ◽  
Rf Sputtering ◽  
Xrd Analysis ◽  
X Ray Diffraction ◽  
Soft Magnetic ◽  
Electrical And Magnetic Properties ◽  
Transmission Electron ◽  
Nanocrystalline Thin Films

Nanocrystalline CoFeHfO thin films have been fabricated by RF sputtering method. Co52Fe23Hf10O15 thin film is observed, exhibit good magnetic properties with magnetic coercivity (Hc) of 0.18 Oe; anisotropy fild (Hk) of 49 Oe; saturation magnetization (4лMs) of 21 kG, and electrical resistivity (ρ) of 300 01cm. The frequency response of permeability of the film is excellent. The effect of microstructure on the electrical and magnetic properties of thin film was studied using X-ray diffraction (XRD) analysis and conventional transmission electron microscopy (TEM). The results showed that excellent soft magnetic properties were associated with granular nannoscale grains of α-CoFe and α-Co(Fe) phases.

Microstructure and Magnetic Properties of Undercooled Fe-50at%Ni Alloys

2011 ◽  
Vol 695 ◽  
pp. 357-360
Author(s):  
Hui Xie ◽  
G. H. Bai ◽  
Lei Jia ◽  
Zhen Lin Lu ◽  
Sheng Zhong Kou
Keyword(s):  
Magnetic Properties ◽  
Optical Microscope ◽  
Phase Identification ◽  
X Ray ◽  
Ni Alloys ◽  
Ni Alloy ◽  
Chemical Constitution ◽  
Maximum Undercooling ◽  
Two Phases ◽  
Microstructure And Magnetic Properties

Bulk Fe-50at%Ni alloy melts were undercooled using cyclic superheating and glass slag purification. As a result, a maximum undercooling up to 217 K could be achieved. As-solidified microstructures were observed by means of optical microscope. Phase identification of Fe-50at%Ni alloys was performed using the Shimadzu X-ray diffractometer (XRD) system. The chemical constitution revealed using a JEOL Model JSM-6700F scanning electron microscope equipped with energy dispersive X-ray spectroscopy (EDX). The magnetic properties of the alloys were measured by vibrating sample magnetometer (VSM) with a DC M-H analyzer. The results indicated that there were twice grain refinements occurred within an undercooling range of 55-217K, where the first could be ascribed to dendrite-remelting, and the second to recrystallization. The phase composition of undercooled Fe-50at%Ni alloys comprised two phases, i.e., solid solution phases withbccandfccstructure. At various undercoolings, the saturation magnetizationMsandHcrelated closely to the measured grain sizeD, and they were in proportion toD-1by the regression analysis.

Effect of Nitridation Magnetic Properties of Nanocrystalline Fe-Co Alloy Powders

2010 ◽  
Vol 654-656 ◽  
pp. 1106-1109
Author(s):  
Ya Qiong He ◽  
Chang Hui Mao ◽  
Jian Yang
Keyword(s):  
Grain Size ◽  
Magnetic Properties ◽  
Alloy Powder ◽  
High Energy ◽  
X Ray Diffraction ◽  
Powder Mixtures ◽  
X Ray ◽  
Transmission Electron ◽  
Nitridation Temperature ◽  
Microstructure And Magnetic Properties

Nanocrystalline Fe-Co alloy powders, which were prepared by high-energy mechanical milling, were nitrided under the mixing gas of NH3/H2 in the temperature range from 380°C to 510°C. X-ray diffraction (XRD) was used to analyze the grain size and reaction during the processing. The magnetic properties of the nitrided powders were measured by Vibrating Sample Magnetometer (VSM). The results show that with the appearance of Fe4N phase after nitride treatment, and the grain-size of FeCo phase decreases with the increase of nitridation temperature between 380°C to 450°C.The saturation magnetization of nitrided alloy powder treated at 480°C is about 18% higher than that of the initial Fe-Co alloy powder, accompanied by the reduction of the coercivity. Transmission electron microscope (TEM) was used, attempting to further analyze the effect of Fe4N phase on microstructure and magnetic properties of the powder mixtures.

Influence of Alloying Additions on Enhancement of Soft Magnetic Properties Effect and Crystallization in FeXSiB (X=Cu, V, Co, Zr, Nb) Amorphous Alloys

2007 ◽  
Vol 130 ◽  
pp. 171-174 ◽  
Author(s):  
Z. Stokłosa ◽  
G. Badura ◽  
P. Kwapuliński ◽  
Józef Rasek ◽  
G. Haneczok ◽  
...  
Keyword(s):  
Magnetic Properties ◽  
Amorphous Alloys ◽  
Crystallization Process ◽  
Annealing Temperature ◽  
Magnetic Measurements ◽  
X Ray Diffraction ◽  
Soft Magnetic ◽  
X Ray ◽  
Second Stage ◽  
Transmission Electron

The crystallization and optimization of magnetic properties effects in FeXSiB (X=Cu, V, Co, Zr, Nb) amorphous alloys were studied by applying X-ray diffraction methods, high resolution transmission electron microscopy (HRTEM), resistometric and magnetic measurements. The temperatures of the first and the second stage of crystallization, the 1h optimization annealing temperature and the Curie temperature were determined for different amorphous alloys. Activation energies of crystallization process were obtained by applying the Kissinger method. The influence of alloy additions on optimization effect and crystallization processes was carefully examined.

scholarly journals The Influence of Annealing Temperature on the Structure and Magnetic Properties of Nanocrystalline BiFeO3 Prepared by Sol–Gel Method

2021 ◽  
Author(s):  
T. Pikula ◽  
T. Szumiata ◽  
K. Siedliska ◽  
V. I. Mitsiuk ◽  
R. Panek ◽  
...  
Keyword(s):  
Grain Size ◽  
Magnetic Properties ◽  
Annealing Temperature ◽  
Sol Gel ◽  
Weak Ferromagnetism ◽  
X Ray Diffraction ◽  
Gel Method ◽  
Sol Gel Method ◽  
Average Grain Size ◽  
Spin Cycloid

AbstractIn this work, BiFeO3 powders were synthesized by a sol–gel method. The influence of annealing temperature on the structure and magnetic properties of the samples has been discussed. X-ray diffraction studies showed that the purest phase was formed in the temperature range of 400 °C to 550 °C and the samples annealed at a temperature below 550 °C were of nanocrystalline character. Mössbauer spectroscopy and magnetization measurements were used as complementary methods to investigate the magnetic state of the samples. In particular, the appearance of weak ferromagnetic properties, significant growth of magnetization, and spin-glass-like behavior were observed along with the drop of average grain size. Mössbauer spectra were fitted by the model assuming cycloidal modulation of spins arrangement and properties of the spin cycloid were determined and analyzed. Most importantly, it was proved that the spin cycloid does not disappear even in the case of the samples with a particle size well below the cycloid modulation period λ = 62 nm. Furthermore, the cycloid becomes more anharmonic as the grain size decreases. The possible origination of weak ferromagnetism of the nanocrystalline samples has also been discussed.

scholarly journals Влияние напряжения смещения и скорости осаждения на структуру и коэрцитивность пленок NiFe

2020 ◽  
Vol 62 (12) ◽  
pp. 2174
Author(s):  
А.С. Джумалиев ◽  
C.Л. Высоцкий ◽  
В.К. Сахаров
Keyword(s):  
Grain Size ◽  
Magnetic Properties ◽  
Film Thickness ◽  
Deposition Rate ◽  
Entire Range ◽  
Soft Magnetic Properties ◽  
Supercritical State ◽  
Dc Magnetron Sputtering ◽  
Soft Magnetic ◽  
Critical Film Thickness

Influence of the bias voltage Ub and the deposition rate  on the structure, grain size D, and coercivity Hc of NiFe films with the thickness d from 30 to 980 nm, grown onto Si / SiO2 substrates by DC magnetron sputtering, was studied. In the case Ub = 0, the decrease of  from ≈ nm/min to ≈ 7 nm/min is accompanied by the increase of the critical film thickness dcr from dcr ≈ 220 nm to dcr ≈ 270 nm. In this case, Hc in the films with d < dcr is characterized by the dependence Hc ~ D6 and varies from ~ 1 to ~ 20 Oe. In the case of Ub = -100 V, the effect of the deposition rate on the coercivity is much more noticeable. At ν = 7 and 14 nm / min, the films demonstrate soft magnetic properties (Нс ≈ 0.15 - 1.4 Oe) and the absence of dcr for the entire range of studied thicknesses. The films obtained at ν = 21 and 27 nm / min turn into the “supercritical” state at d ≥ dcr ≈ 520 nm, and, in the region d < dcr, they are characterized by the dependence Hc ~ D3 and by the increase of coercivity from ~ 0.35 to ~ 10 Oe.

TEM Study of FePt and FePt:C/FePt Composite Double-Layered Thin Films

2013 ◽  
Vol 275-277 ◽  
pp. 1952-1955
Author(s):  
Ling Fang Jin ◽  
Xing Zhong Li
Keyword(s):  
Electron Microscopy ◽  
Thin Films ◽  
Transmission Electron Microscopy ◽  
Grain Size ◽  
Magnetic Properties ◽  
Composite Layer ◽  
X Ray Diffraction ◽  
X Ray ◽  
Transmission Electron

New functional nanocomposite FePt:C thin films with FePt underlayers were synthesized by noneptaxial growth. The effect of the FePt layer on the ordering, orientation and magnetic properties of the composite layer has been investigated by adjusting FePt underlayer thickness from 2 nm to 14 nm. Transmission electron microscopy (TEM), together with x-ray diffraction (XRD), has been used to check the growth of the double-layered films and to study the microstructure, including the grain size, shape, orientation and distribution. XRD scans reveal that the orientation of the films was dependent on FePt underlayer thickness. In this paper, the TEM studies of both single-layered nonepitaxially grown FePt and FePt:C composite L10 phase and double-layered deposition FePt:C/FePt are presented.

Al Effect on the Structure of the Spray Formed Fe88Si12 (at%) Alloy

2008 ◽  
Vol 570 ◽  
pp. 150-154 ◽  
Author(s):  
F. Saporiti ◽  
A.H. Kasama ◽  
B. Arcondo ◽  
Walter José Botta Filho ◽  
Claudio Shyinti Kiminami ◽  
...  
Keyword(s):  
Magnetic Properties ◽  
Low Temperatures ◽  
Spray Forming ◽  
Order Reaction ◽  
Soft Magnetic Properties ◽  
Thin Sheets ◽  
X Ray Diffraction ◽  
Soft Magnetic ◽  
Silicon Alloys ◽  
X Ray

Fe-Si alloys have excellent soft magnetic properties, specially around 12 at% Si. However, its industrial application is limited because of the lack of ductility, which causes cracking during rolling operations for the fabrication of thin sheets. The reason of the brittleness of the high silicon alloys is a disorder/order reaction at low temperatures. The aim of this work is to analyze the effect of the addition of Aluminum on the crystalline structure of Fe-Si alloys. Samples with a chemical composition of Fe88Si12 and Fe87Si12Al1 (at%) were prepared by Spray Forming. The structure was studied by means of X-ray diffraction and Mössbauer Spectroscopy. The presence of the DO3 and α- Fe phases were observed

Nanocrystallization of Fe-Based Amorphous Alloys Fe73.5Cu1Nb3Si13.5B9 by Yb-Doped Fiber Laser Overlapping Irradiation

2012 ◽  
Vol 482-484 ◽  
pp. 2365-2370 ◽  
Author(s):  
Qian Li Ma ◽  
Yong Bao ◽  
Guo Rui Zhang ◽  
Li Meng Yu ◽  
Ling Fei Ji ◽  
...  
Keyword(s):  
Magnetic Properties ◽  
Fiber Laser ◽  
Laser Irradiation ◽  
Soft Magnetic Property ◽  
Internal Diameter ◽  
Soft Magnetic Properties ◽  
External Diameter ◽  
X Ray Diffraction ◽  
Soft Magnetic ◽  
Transmission Electron

The paper presents a laser irradiation method for rapidly fabricating Fe-based nanocrystalline alloys using Yb-doped fiber laser with a wavelength of 1070nm by overlapping irradiation of the heated areas. The samples are annular cores rolled with 20μm-thick and 3.2mm-wide belts of amorphous alloy Fe73.5Cu1Nb3Si13.5B9, which have internal diameter of 14 mm and external diameter of 20 mm. Every side of the samples is irradiated for 15 min by fiber laser. X-ray diffraction and transmission electron microscopy (TEM) are used for microstructure analysis and observation. The samples irradiated by a defocus beam with a diameter of 7.1mm through a lens have better soft magnetic properties than directly by an original collimating beam with a diameter of 6.7mm. The dimension of homogeneous ultrafine grains is about 10nm with a bcc α-Fe (Si), which is the foundation of the excellent soft magnetic property. Uniform laser irradiation and the appropriate laser power are necessary for optimum microstructure and soft magnetic properties.

Sign in / Sign up

Export Citation Format

Share Document