Ultrafine Structure Formation in Aluminium Alloy Processed by HPT and the Mechanical Properties Response

2010 ◽  
Vol 667-669 ◽  
pp. 903-908
Author(s):  
Jozef Zrník ◽  
Reinhard Pippan ◽  
Stephan Scheriau ◽  
Martin Fujda
Keyword(s):  
Thermal Treatment ◽  
Aluminium Alloy ◽  
Structure Formation ◽  
Structure Refinement ◽  
Strain Level ◽  
Structure Evolution ◽  
Ultrafine Grain ◽  
Initial Structure ◽  
Increased Temperature ◽  
The Impact

In this study ultrafine grain structure evolution during high pressure torsion (HPT) of commercial aluminium alloy AA6082 at increased temperature is presented. Two different initial structural states of the alloy were prepared by thermal treatment. The progress in structure refinement in dependence on the shear strain level strain was investigated by TEM of thin foils. The impact of different amount of strain (εef) introduced was analyzed with respect to the effect of increased temperature. The microhardness results measured across the deformed discs pointed out that some data scattering. The results of microstructure analyses showed that ultrafine grain (ufg) structure was already formed in deformed disc upon the first turn, regardless the initial structure of alloy, resulting from prior thermal treatment. The observed heterogeneity in ufg structure formation across the deformed disc was observed, supporting microhardness results scattering. By increasing the strain level (number of turns N -2,4,6), more effectively homogenized ufg structure was observed across the deformed discs. The effect of increased deformation temperature became evident and dynamic recrystalization modified locally ufg structure. The retardation of new grains growth and higher thermal stability of ufg structure was observed, when two steps thermal treatment of alloy (quenching and ageing) was executed prior deformation. Strength measurements results yielded from tensile tests showed that the effect of structure strengthening was degraded by local recrystallization. The results of torque measurement versus the time showed that the torque required to deform the sample was increasing until the first turn and then kept stable or even decreased.

Ultrafine Grain Structure Evolution in AA6085 Aluminium Alloy Processed by HPT at Increased Temperature

2012 ◽  
Vol 706-709 ◽  
pp. 1864-1869
Author(s):  
Jozef Zrník ◽  
Libor Kraus ◽  
Stephan Scheriau ◽  
Reinhard Pippan
Keyword(s):  
Thermal Treatment ◽  
Aluminium Alloy ◽  
Strain Level ◽  
Grain Structure ◽  
Structure Evolution ◽  
Ultrafine Grain ◽  
Initial Structure ◽  
Increased Temperature ◽  
Ultrafine Grain Structure ◽  
The Impact

In this study ultrafine grain structure evolution during high pressure torsion (HPT) of commercial aluminium alloy AA6082 at increased temperature is presented. Two different initial structural states of the alloy were prepared by thermal treatment. The progress in structure refinement in dependence on the shear strain level strain was investigated by TEM of thin foils. The impact of different amount of strain (εef) introduced was analyzed with respect to the effect of increased temperature. The microhardness results measured across the deformed discs pointed out that some data scattering. The results of microstructure analyses showed that ultrafine grain (ufg) structure was already formed in deformed disc upon the first turn, regardless the initial structure of alloy, resulting from prior thermal treatment. The observed heterogeneity in ufg structure formation across the deformed disc was observed, supporting microhardness results scattering. By increasing the strain level (number of turns N-2,4,6), more effectively homogenized ufg structure was observed across the deformed discs. The effect of increased deformation temperature became evident and dynamic recrystalization modified locally ufg structure.. The retardation of new grains growth and higher thermal stability of ufg structure was observed, when two steps thermal treatment of alloy (quenching and ageing) was executed prior deformation. Strength measurements results yielded form tensile tests showed that the effect of structure strengthening was degraded by local recrystallization. The results of torque measurement versus the time showed that the torque required to deform the sample was increasing until the first turn and then kept stable or even decreased.

scholarly journals Spring Model – chromatin modeling tool based on OpenMM

2019 ◽  
Author(s):  
Michal Kadlof ◽  
Julia Rozycka ◽  
Dariusz Plewczynski
Keyword(s):  
Local Density ◽  
Structure Refinement ◽  
3D Structure ◽  
Data Bank ◽  
Chromatin Domain ◽  
Initial Structure ◽  
Domain Modeling ◽  
Building Models ◽  
Spherical Container ◽  
The Impact

AbstractChromatin structures modelling is a rapidly developing field. Parallel to the enormous growth of available experimental data, there is a growing need of building and visualizing 3D structures of nuclei, chromosomes, chromatin domains, and single loops associated with particular genes locus. Here we present a tool for chromatin domain modeling. It is available as a webserver and standalone python script. Our tool is based on molecular mechanics. It uses OpenMM engine for building models. In this method, the user has to provide contacts and will obtain 3D structure that satisfies these contacts. Additional extra parameters allow controlling fibre stiffness, type of initial structure, resolution. There are also options for structure refinement, and modelling in a spherical container. A user may provide contacts using beads indices, or paste interactions in genome coordinates from BEDPE file. After modelling user is able to download the structure in Protein Data Bank (PDB) file format for further analysis.We dedicate this tool for all who are interested in chromatin structures. It is suitable for quick visualization of datasets, studying the impact of structural variants (SVs), inspecting the effects of adding and removing particular contacts, measuring features like maximum distances between certain sites (e.g. promotor-enhancer) or local density of chromatin.

Effect of Preliminary Treatment on Grain Refinement of Medium Carbon Steel Using ECAP at Increased Temperature

2010 ◽  
Vol 638-642 ◽  
pp. 2013-2018 ◽  
Author(s):  
Jozef Zrník ◽  
Sergey V. Dobatkin ◽  
Martin Fujda ◽  
Jan Džugan
Keyword(s):  
Carbon Steel ◽  
Grain Refinement ◽  
Structure Refinement ◽  
Medium Carbon Steel ◽  
Ultrafine Grain ◽  
Initial Structure ◽  
Strength Increase ◽  
Preliminary Treatment ◽  
Medium Carbon ◽  
Treated Steel

By application of thermomechanical controlled rolling and accelerated cooling, the carbon steel grain refinement is limited to levels of ~ 5 μm in steels. The strain assisted or strain induced transformation could be considered for the refining process. The present work, likewise, deals with grain refinement of medium carbon steel containing 0.45 wt pct carbon having different initial microstructure modified by either thermal and/or thermomechanical treatment (TM) prior severe plastic deformation. In case of TM treated steel, structure refinement was conducted in two steps. Preliminary structure refinement has been achieved due to multistep open die forging process which provided total strain of 3. Uniform and fine recrystallized ferrite structure with grain size of the order of 2-5 μm and with nest-like pearlite colonies was obtained. The further grain refinement of steel samples having different initial structure was accomplished during warm Equal Channel Angular Pressing (ECAP) at 400°C. The steel samples of different initial structure were then subjected to six ECAP pressing passes through die channel angle of 120°. The microstructure development was analyzed in dependence of effective strain introduced (εef ~ 2.5 - 4). Employment of this processing route resulted in extensive deformation of ferrite grains where mixture of subgrains and ultrafine grain was found regardless the preliminary treatment of steel. As straining increases the dynamic polygonization and recrystallization became active to form mixture of polygonized subgrains and submicrocrystalline grains having high angle boundaries. The straining and moderate ECAP temperature caused the partial cementite lamellae fragmentation and spheroidization as straining increased. The lamellae cementite spheroidization was more extensive in TM treated steel samples. The tensile behavior was characterized by strength increase for both structural steel states; however the work hardening behavior was modified in steel where preliminary TM treatment was introduced to modified coarse ferrite-pearlite structure.

scholarly journals Metastable Austenitic Steel Structure and Mechanical Properties Evolution in the Process of Cold Radial Forging

Materials ◽  
2019 ◽  
Vol 12 (13) ◽  
pp. 2058 ◽  
Author(s):  
Panov ◽  
Pertsev ◽  
Smirnov ◽  
Khotinov ◽  
Simonov
Keyword(s):  
Impact Strength ◽  
Structure Formation ◽  
True Strain ◽  
Steel Structure ◽  
Grain Structure ◽  
Structure Evolution ◽  
Austenite Formation ◽  
Radial Forging ◽  
Deformation Degree ◽  
The Impact

The article presents the influence of structure formation on the properties of 321 metastable austenitic stainless steel in the process of cold radial forging (CRF). The steel under study after austenitization was subjected to CRF at room temperature with degrees of true strain (e) 0.26, 0.56, 1.00, 1.71 and 2.14. It has been shown that structure formation of the studied steel during CRF consists of three stages: formation of the lamellar structure of austenite, formation of the trapezoidal structure, and formation of the equiaxial grain structure. The kinetics of the strain-induced α’-martensitic transformation is related to the stages of structure evolution. Hardness, ultimate tensile strength and yield strength uniformly increase in all stages of structure formation with a significant decrease of elongation to fracture during the first stage of structure formation while the value of elongation to fracture remains constant in the subsequent stages of deformation. Impact strength of fatigue cracked specimens (KCT) decreases sharply at the first stage of structure formation and smoothly increases at the second and third stages. However, the impact strength of V-notch specimens (KCV) continuously decreases when deformation degree increases in the overall investigated deformation range.

scholarly journals A multilevel investigation supported by multivariate analysis for tomato product formulation

2021 ◽  
Author(s):  
Fatma Boukid ◽  
Elena Curti ◽  
Agoura Diantom ◽  
Eleonora Carini ◽  
Elena Vittadini
Keyword(s):  
Thermal Treatment ◽  
Color Change ◽  
Water Molecules ◽  
Thermal Treatments ◽  
Industrial Processing ◽  
H Nmr ◽  
Mobile Populations ◽  
Product Formulation ◽  
Tomato Product ◽  
The Impact

AbstractIndustrial processing of tomato includes its cutting and mincing, thermal treatments, and the addition of ingredients, which might induce changes in physicochemical properties of the final products. In this frame, the impact of texturing/thickening [xanthan gum (X) or potato fiber (F)] on the macroscopic, mesoscopic and molecular properties of tomato double concentrate (TDC) was investigated to determine if F can efficiently substitute X, in association with small solutes (sugar and salt) and thermal treatment (cold and hot). At a macroscopic level, multivariate statistics (MANOVA) underlined that color change (ΔE) was increased by X and F addition contrary to heating and the addition of salt and sugar. MANOVA revealed that texture was greatly enhanced through the use of F over X. 1H NMR molecular mobility changes were more controlled by texturing agents (F and X) than thermal treatment and small solutes. Particularly F increased the more rigid population indicating stronger interaction with water molecules resulting in shear-thinning flow. However, adding X contributed into the increase of the dynamic and mobile populations. Therefore, F can be a valid “clean label” substitute of X in modulating tomato products properties.

scholarly journals Aluminium Alloy Foam Modelling and Prediction of Elastic Properties Using X-ray Microcomputed Tomography

Metals ◽  
2021 ◽  
Vol 11 (6) ◽  
pp. 925
Author(s):  
Diogo Heitor ◽  
Isabel Duarte ◽  
João Dias-de-Oliveira
Keyword(s):  
Aluminium Alloy ◽  
Finite Element Modelling ◽  
Effective Properties ◽  
Numerical Models ◽  
Microcomputed Tomography ◽  
Cellular Materials ◽  
Metallic Foams ◽  
X Ray ◽  
The Impact ◽  
Structural Imperfections

X-ray microcomputed tomography has been gaining relevance in the field of cellular materials to characterize materials and analyse their microstructure. So, here, it was used together with finite element modelling to develop numerical models to estimate the effective properties (Young’s modulus) of aluminium alloy foams and evaluate the effects of processing on the results. A manual global thresholding technique using the mass as a quality indicator was used. The models were reconstructed (Marching Cubes 33), then simplified and analysed in terms of mass and shape maintenance (Hausdorff distance algorithm) and face quality. Two simplification procedures were evaluated, with and without small structural imperfections, to evaluate the impact of the procedures on the results. Results demonstrate that the developed procedures are good at minimizing changes in mass and shape of the geometries while providing good face quality, i.e., face aspect ratio. The models are also shown to be able to predict the effective properties of metallic foams in accordance with the findings of other researchers. In addition, the process of obtaining the models and the presence of small structural imperfections were shown to have a great impact on the results.

Physical Based Microstructure Modelling Coupled with Nucleation Theory during and after Hot Forming of AA5083

2010 ◽  
Vol 89-91 ◽  
pp. 509-514
Author(s):  
Pavel Sherstnev ◽  
Christof Sommitsch ◽  
Stefan Mitsche ◽  
Carsten Melzer
Keyword(s):  
Aluminium Alloy ◽  
Hot Rolling ◽  
Volume Fraction ◽  
Electron Backscatter Diffraction ◽  
Grain Structure ◽  
Nucleation Theory ◽  
Structure Evolution ◽  
Nucleation Sites ◽  
Nucleation Mechanisms ◽  
Backscatter Diffraction

A physical model based on three types of dislocations and three nucleation sites for recrystallized grain is applied to hot rolling simulation. This model was implemented into a commercial Finite Element (FE) analysis package FORGE 2008 to calculate both the structure evolution during and the recrystallized volume fraction after hot working of aluminium alloy 5083. It is shown that the main nucleation mechanisms in the aluminium alloy are the particle stimulated nucleation (PSN) and nucleation at grain boundaries. Hence the precipitation kinetics during homogenisation was investigated by use of the thermodynamic calculation software MatCalc. To validate the simulation results hot rolling experiments were performed by means of a laboratory mill. The grain structure evolution was analysed by electron backscatter diffraction (EBSD).

Grain Structure Formation Ahead of Tool during Friction Stir Welding of AZ31 Magnesium Alloy

2010 ◽  
Vol 160 ◽  
pp. 313-318 ◽  
Author(s):  
Uceu Suhuddin ◽  
Sergey Mironov ◽  
H. Takahashi ◽  
Yutaka S. Sato ◽  
Hiroyuki Kokawa ◽  
...  
Keyword(s):  
Friction Stir Welding ◽  
Magnesium Alloy ◽  
Structure Formation ◽  
Material Flow ◽  
Boundary Migration ◽  
Deformation Mode ◽  
Grain Structure ◽  
Az31 Magnesium Alloy ◽  
Structure Evolution ◽  
Friction Stir

The “stop-action” technique was employed to study grain structure evolution during friction-stir welding of AZ31 magnesium alloy. The grain structure formation was found to be mainly governed by the combination of the continuous and discontinuous recrystallization but also involved geometric effect of strain and local grain boundary migration. Orientation measurements showed that the deformation mode was very close to the simple shear associated with the rotating pin and material flow arose mainly from basal slip.

scholarly journals Evaluation of Mechanical, Microstructures and Wear Behaviours of Aluminium Alloy Reinforced with Mussel Shell Powder for Automobile Applications

2021 ◽  
Vol 67 (1-2) ◽  
pp. 27-35
Author(s):  
Idawu Yakubu Suleiman ◽  
Auwal Kasim ◽  
Abdullahi Tanko Mohammed ◽  
Munir Zubairu Sirajo
Keyword(s):  
Mechanical Properties ◽  
Aluminium Alloy ◽  
Automobile Industry ◽  
Testing Machine ◽  
Wear Testing ◽  
Wear Behaviour ◽  
Mussel Shell ◽  
The Matrix ◽  
The Impact ◽  
Shell Powder

This paper aims to investigate the mechanical (tensile, hardness, impact, elongation), microstructure and wear behaviours of aluminium alloy reinforced with mussel shell powder (MSP) at different weight percentages (0 wt. % to 15 wt. %) at 3 wt. % interval. The mussel shell powder was characterized by X-ray fluorescence (XRF). The matrix and the composites’ morphology were studied using a scanning electron microscope attached with energy dispersive spectroscopy for the distribution of mussel shell powder particles within the matrix. The wear behaviour of the alloy and composites produced at various reinforcements were carried out using a Taber abrasion wear-testing machine. The XRF showed the compositions of MSP to contain calcium oxide (95.70 %), silica (0.83 %) and others. Mechanical properties showed that tensile values increase with increases in MSP, hardness value increases from 6 wt. % to 15 wt. % of MSP. The impact energy decreased from 42.6 J at 3 wt. % to 22.6 J at 15 wt. %; the percentage elongation also decreased from 37.4 % at 3 wt. % to 20.5 % at 15 wt. % MSP, respectively. The bending stress results increase with increases in the percentage of reinforcement. The morphologies revealed that uniform distribution of MSP within the matrix resulted to improvement in mechanical properties. The wear resistance of the composites increases with increase in the applied load and decreases with increases in the weight percentage of MSP and can be used in the production of brake pads and insulators in the automobile industry.

Sign in / Sign up

Export Citation Format

Share Document