scholarly journals Effects of CNT Addition on Mechanical Properties, Electric Conductivity and Oxidation Resistance of Al2O3-TiC Composite

2013 ◽  
Vol 761 ◽  
pp. 83-86
Author(s):  
Hideaki Sano ◽  
Junichi Morisaki ◽  
Guo Bin Zheng ◽  
Yasuo Uchiyama
Keyword(s):  
Mechanical Properties ◽  
Carbon Nanotubes ◽  
Fracture Toughness ◽  
Flexural Strength ◽  
Electric Conductivity ◽  
Young’S Modulus ◽  
Oxidation Resistance ◽  
Young's Modulus ◽  
Tic Particle

Effects of carbon nanotubes (CNT) addition on mechanical properties, electric conductivity and oxidation resistance of CNT/Al2O3-TiC composite were investigated. It was found that flexural strength, Young’s modulus and fracture toughness of the composites were improved by addition of more than 2 vol%-CNT. In the composites with more than 3 vol%-CNT, the oxidation resistance of the composite was degraded. In comparison with Al2O3-26vol%TiC sample as TiC particle-percolated sample, the Al2O3-12vol%TiC-3vol%CNT sample, which is not TiC particle-percolated sample, shows almost the same mechanical properties and electric conductivity, and also shows thinner oxidized region after oxidation at 1200°C due to less TiC in the composite.

Densification, Microstructure, and Behavior of Hydroxyapatite Ceramics Sintered by Using Spark Plasma Sintering

2008 ◽  
Vol 130 (3) ◽  
Author(s):  
Shufeng Li ◽  
Hiroshi Izui ◽  
Michiharu Okano
Keyword(s):  
Mechanical Properties ◽  
Fracture Toughness ◽  
Flexural Strength ◽  
Relative Density ◽  
Young’S Modulus ◽  
Spark Plasma Sintering ◽  
Young's Modulus ◽  
Plasma Sintering ◽  
Spark Plasma ◽  
Temperature And Pressure

This paper discusses the dependence of the mechanical properties and microstructure of sintered hydroxyapatite (HA) on the sintering temperature and pressure. A set of specimens was prepared from as-received HA powder and sintered by using a spark plasma sintering (SPS) process. The sintering pressures were set at 22.3MPa, 44.6MPa, and 66.9MPa, and sintering was performed in the temperature range from 800°Cto1000°C at each pressure. Mechanisms underlying the interrelated temperature-mechanical and pressure-mechanical properties of dense HA were investigated. The effects of temperature and pressure on the flexural strength, Young’s modulus, fracture toughness, relative density, activation energy, phase stability, and microstructure were assessed. The relative density and grain size increased with an increase in the temperature. The flexural strength and Young’s modulus increased with an increase in the temperature, giving maximum values of 131.5MPa and 75.6GPa, respectively, at a critical temperature of 950°C and 44.6MPa, and the fracture toughness was 1.4MPam1∕2 at 1000°C at 44.6MPa. Increasing the sintering pressure led to acceleration of the densification of HA.

Mechanical properties and toughening mechanisms of epoxy/graphene nanocomposites

2015 ◽  
Vol 35 (3) ◽  
pp. 257-266 ◽  
Author(s):  
Rahim Eqra ◽  
Kamal Janghorban ◽  
Habib Daneshmanesh
Keyword(s):  
Mechanical Properties ◽  
Fracture Surface ◽  
Flexural Strength ◽  
Young’S Modulus ◽  
Young's Modulus ◽  
Graphene Nanosheets ◽  
Flexural Modulus ◽  
Mechanical Tests ◽  
Toughening Mechanism ◽  
Graphene Nanocomposites

Abstract Because of extraordinary physical, chemical and mechanical properties, graphene nanosheets (GNS) are suitable fillers for optimizing the properties of different polymers. In this research, the effect of GNS content (up to 1 wt.%) on tensile and flexural properties, morphology of fracture surface, and toughening mechanism of epoxy were investigated. Results of mechanical tests showed a peak for tensile and flexural strength of samples with 0.1 wt.% GNS such that the tensile and flexural strength improved by 13% and 3.3%, respectively. The Young’s modulus and flexural modulus increased linearly with GNS content, although the behavior of the Young’s modulus was more remarkable. Morphological investigations confirmed this behavior because the GNS dispersion in the epoxy matrix was uniform at lower contents and agglomerated at higher contents. Finally, microscopical observation showed that the major toughening mechanism of graphene-epoxy nanocomposites was crack path deflection, which changed the mirror fracture surface of the pure epoxy to rough surface.

scholarly journals Preliminary Study on Mechanical Properties of 3D Printed Multimaterials ABS/PC Parts: Effect of Printing Parameters

2021 ◽  
Vol 32 (2) ◽  
pp. 87-104
Author(s):  
Pui-Voon Yap ◽  
Ming-Yeng Chan ◽  
Seong-Chun Koay
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Flexural Strength ◽  
Young’S Modulus ◽  
Young's Modulus ◽  
Flexural Modulus ◽  
Nozzle Diameter ◽  
Fused Deposition ◽  
Printing Parameters ◽  
Printing Speed

This research work highlights the mechanical properties of multi-material by fused deposition modelling (FDM). The specimens for tensile and flexural test have been printed using polycarbonate (PC) material at different combinations of printing parameters. The effects of varied printing speed, infill density and nozzle diameter on the mechanical properties of specimens have been investigated. Multi-material specimens were fabricated with acrylonitrile butadiene styrene (ABS) as the base material and PC as the reinforced material at the optimum printing parameter combination. The specimens were then subjected to mechanical testing to observe their tensile strength, Young’s modulus, percentage elongation, flexural strength and flexural modulus. The outcome of replacing half of ABS with PC to create a multi-material part has been examined. As demonstrated by the results, the optimum combination of printing parameters is 60 mm/s printing speed, 15% infill density and 0.8 mm nozzle diameter. The combination of ABS and PC materials as reinforcing material has improved the tensile strength (by 38.46%), Young’s modulus (by 23.40%), flexural strength (by 23.90%) and flexural modulus (by 37.33%) while reducing the ductility by 14.31% as compared to pure ABS. The results have been supported by data and graphs of the analysed specimens.

scholarly journals Effect of Water on Some Mechanical Properties for Sawdust and Chopped Reeds /UPE composites

2011 ◽  
Vol 8 (2) ◽  
pp. 551-560
Author(s):  
Baghdad Science Journal
Keyword(s):  
Mechanical Properties ◽  
Weight Gain ◽  
Flexural Strength ◽  
Young’S Modulus ◽  
Polyester Resin ◽  
Young's Modulus ◽  
Unsaturated Polyester ◽  
Molding Method ◽  
Effect Of Water ◽  
Composite Samples

In this study, composite materials were prepared using unsaturated polyester resin as binder with two types of fillers (sawdust and chopped reeds). The molding method is used to prepare sheets of UPE / sawdust composite and UPE / chopped reeds composite. The mechanical properties were studied including flexural strength and Young's modulus for the samples at normal conditions (N.C). The Commercial wood, UPE and its composite samples were immersed in water for about 30 days to find the weight gain (Mt%) of water for the samples, also to find the effect of water on their flexural strength and Young's modulus. The results showed that the samples of UPE / chopped reeds composite gained highest values of flexural strength (24.5 MPa) and Young's modulus (5.1 GPa) as compared with other composites at (N.C). The results showed that the wet samples of sawdust composite have lowest values of weight gain (Mt %) of water (0.043%) as compared with other composites after immersion. Also it’s showed a slight decrease in values of Young's modulus for all the samples after immersion as compared with the samples at (N.C). Finally it’s showed a slight decrease in values of flexural strength for all the samples except for the composite material formed from UPE / chopped reeds which showed an increase in the value of flexural strength after immersion, where the wet samples of UPE / chopped reeds composite gained (29 MPa) as compared with the samples at (N.C).

scholarly journals Effective reinforcements for thermoplastics based on carbon nanotubes of oil fly ash

2019 ◽  
Vol 9 (1) ◽  
Author(s):  
Numan Salah ◽  
Abdulrahman Muhammad Alfawzan ◽  
Abdu Saeed ◽  
Ahmed Alshahrie ◽  
Waleed Allafi
Keyword(s):  
Mechanical Properties ◽  
Carbon Nanotubes ◽  
Tensile Strength ◽  
Fly Ash ◽  
Young’S Modulus ◽  
Raw Materials ◽  
Young's Modulus ◽  
Weight Fraction ◽  
Low Weight ◽  
Oil Fly Ash

AbstractCarbon nanotubes (CNTs) are widely investigated for preparing polymer nanocomposites, owing to their unique mechanical properties. However, dispersing CNTs uniformly in a polymer matrix and controlling their entanglement/agglomeration are still big technical challenges to be overcome. The costs of their raw materials and production are also still high. In this work, we propose the use of CNTs grown on oil fly ash to solve these issues. The CNTs of oil fly ash were evaluated as reinforcing materials for some common thermoplastics. High-density polyethylene (HDPE) was mainly reinforced with various weight fractions of CNTs. Xylene was used as a solvent to dissolve HDPE and to uniformly disperse the CNTs. Significantly enhanced mechanical properties of HDPE reinforced at a low weight fraction of these CNTs (1–2 wt.%), mainly the tensile strength, Young’s modulus, stiffness, and hardness, were observed. The tensile strength and Young’s modulus were enhanced by ~20 and 38%, respectively. Moreover, the nanoindentation results were found to be in support to these findings. Polycarbonate, polypropylene, and polystyrene were also preliminarily evaluated after reinforcement with 1 wt.% CNTs. The tensile strength and Young’s Modulus were increased after reinforcement with CNTs. These results demonstrate that the CNTs of the solid waste, oil fly ash, might serve as an appropriate reinforcing material for different thermoplastics polymers.

scholarly journals Modeling the Mechanical Properties of Functionalized Carbon Nanotubes and Their Composites: Design at the Atomic Level

2014 ◽  
Vol 2014 ◽  
pp. 1-8 ◽  
Author(s):  
Qing-Sheng Yang ◽  
Bing-Qi Li ◽  
Xiao-Qiao He ◽  
Yiu-Wing Mai
Keyword(s):  
Mechanical Properties ◽  
Carbon Nanotubes ◽  
Molecular Dynamics ◽  
Tensile Strength ◽  
Young’S Modulus ◽  
Young's Modulus ◽  
Atomic Level ◽  
Functionalized Carbon Nanotubes ◽  
Buckling Stress ◽  
Compressive Buckling

This investigation focuses on the design of functionalization configuration at the atomic level to determine the influence of atomic structure on the mechanical properties of functionalized carbon nanotubes (F-CNTs) and their composites. Tension and compressive buckling behaviors of different configurations of CNTs functionalized by H atoms are studied by a molecular dynamics (MD) method. It is shown that H-atom functionalization reduces Young’s modulus of CNTs, but Young’s modulus is not sensitive to the functionalization configuration. The configuration does, however, affect the tensile strength and critical buckling stress of CNTs. Further, the stress-strain relations of composites reinforced by nonfunctionalized and various functionalized CNTs are analyzed.

High Temperature Mechanical Properties of Ni-YSZ Cermets for SOFC Anode

2010 ◽  
Author(s):  
Fumitada Iguchi ◽  
Hiromichi Kitahara ◽  
Hiroo Yugami
Keyword(s):  
Mechanical Properties ◽  
High Temperature ◽  
Flexural Strength ◽  
Young’S Modulus ◽  
Young's Modulus ◽  
Strain Diagram ◽  
Thermal Cycles ◽  
High Temperature Mechanical Properties ◽  
Sofc Anode ◽  
The Difference

The mechanical properties of Ni-YSZ cermets at high temperature in reduction atmosphere were evaluated by the four points bending method. We studied the influences of reduction and thermal cycles, i.e. a cycle from R.T. to 800°C, to flexural strength and Young’s modulus. The flexural strength of Ni-YSZ at room temperature was lower than that of NiO-YSZ by about 10 to 20% mainly caused by the increment of porosity. But, the flexural strength of Ni-YSZ at 800°C was drastically decreased by an half of that at R.T. In addition, the stress–strain diagram of Ni-YSZ at 800°C indicated that it showed weak ductility. The maximum observed strain was over 0.5% at 30MPa. On the contrary, NiO-YSZ showed only brittlely at 800°C. The difference was caused by Ni metal in the Ni-YSZ cermets. Therefore, it was expected that Ni-YSZ is easily deformed in operation, though residual stress between an anode and an electrolyte was low. The influence of thermal cycles to flexural strength and Young’s modulus was not observed clearly. At the same time, the differences of microstructure were not observed. Therefore, it was concluded that the cycle does not change mechanical properties significantly.

Mechanical Properties and Machinability of Si3N4/hBN Composites Prepared by Pressureless Sintering

2006 ◽  
Vol 510-511 ◽  
pp. 1014-1017 ◽  
Author(s):  
Won Seung Cho ◽  
Ki Ju Lee ◽  
Myeong Woo Cho ◽  
Jae Hyung Lee ◽  
Woon Suk Hwang
Keyword(s):  
Mechanical Properties ◽  
Flexural Strength ◽  
Young’S Modulus ◽  
Young's Modulus ◽  
Ceramic Composites ◽  
Pressureless Sintering ◽  
Si3n4 Ceramic ◽  
Cutting Resistance ◽  
Axis Parallel ◽  
Si3n4 Ceramics

The effects of hBN content on microstructure, mechanical properties, and machinability of the pressureless-sintered Si3N4 ceramics were investigated. Flexural strength, Young’s modulus, and hardness decreased with increasing h-BN content. The mechanical properties are decreased mainly because of increased porosity of composite, and the much lower Young's modulus of BN compared to that of Si3N4. Pressureless-sintered Si3N4/hBN composites exhibit strong texture of BN grains oriented with the c-axis parallel to the cold-pressing direction. Cutting resistance of Si3N4 ceramic composites with more than 10 vol% hBN decreased with increasing hBN content, demonstrating a good machinability of the composites. The residual pores can be attributed to improved machinability of pessureless-sintered Si3N4-BN composite.

Influence of Injection Molding Parameters on Mechanical Properties of Low Density Polyethylene Filled With Multiwalled Carbon Nanotubes

2011 ◽  
Author(s):  
Catalin Fetecau ◽  
Felicia Stan ◽  
Daniel Dobrea ◽  
Dan Catalin Birsan
Keyword(s):  
Mechanical Properties ◽  
Carbon Nanotubes ◽  
Injection Molding ◽  
Young’S Modulus ◽  
Young's Modulus ◽  
Flow Direction ◽  
Mold Temperature ◽  
Low Density Polyethylene ◽  
Low Density ◽  
Melt Temperature

In this paper, we investigated the effect of injection molding parameters such as melt temperature, mold temperature, injection speed and holding pressure on the mechanical properties of low density polyethylene reinforced with 2.5 wt% multi-walled carbon nanotubes. The Taguchi methodology with four factors and two levels was used for the design of the injection molding experiments. The mechanical properties were evaluated by tensile tests in the flow direction at room temperature (23 °C) at crosshead speeds of 1 and 5 mm/min. It was found that the mechanical properties can be modified by manipulating the injection molding parameters. The Young’s modulus of the LDPE-MWNTs composite decreased as the melt temperature increased, while mold temperature, injection molding speed and holding pressure have a moderate influence on the Young’s modulus.

Mechanical properties of zigzag-shaped carbon nanotubes: the roles of the geometric parameters

RSC Advances ◽  
2016 ◽  
Vol 6 (33) ◽  
pp. 27999-28004
Author(s):  
Lizhao Liu
Keyword(s):  
Mechanical Properties ◽  
Carbon Nanotubes ◽  
Young’S Modulus ◽  
Young's Modulus ◽  
Geometric Parameters ◽  
Intrinsic Strength

Empirical formulae were fitted to describe relationships between the intrinsic strength/Young's modulus and curvature of the Z-CNTs.

Sign in / Sign up

Export Citation Format

Share Document