Evaluation of Incorporation of Special Vitreous Residues in Mass for Porcelain Stoneware: Physical and Mechanical Properties

2015 ◽  
Vol 820 ◽  
pp. 600-604
Author(s):  
A.M.B Araújo ◽  
V.S. Porto ◽  
C.R.S. Morais ◽  
M.S.L. Cavalcanti
Keyword(s):  
Mechanical Properties ◽  
Water Absorption ◽  
Flexural Modulus ◽  
Physical And Mechanical Properties ◽  
Linear Shrinkage ◽  
Mechanical Tests ◽  
Fluorescent Lamps

This study aimed to technological alternatives for reuse of vitreous residues from fluorescent lamps, which cause damage to the environment. It was prepared mass to white ceramic with and without lamps residues replacing partially feldspar in proportions of 5% and 10%. Samples were molded and fired at 1000 ° C, 1100 ° C, 1150 ° C, 1200 ° C and 1250 ° C. Physical and mechanical tests were: water absorption, linear shrinkage and rupture by flexural modulus. Samples with 10% of residues reached stability at temperature less than 1250 ° C in all determined properties, confirming the feasibility of these residues in ceramic masses. To optimize the study, it was prepared other samples in proportions of 15% and 20% of waste, at the same level of burning and testing. Results obtained ratified the possibility of using these residues as a flux in ceramic slurries.

Use of Ash from Coffee Wood into Clayey Ceramic

2014 ◽  
Vol 775-776 ◽  
pp. 712-717
Author(s):  
Bianca Silva dos Santos ◽  
Veronica Scarpini Candido ◽  
Sergio Neves Monteiro ◽  
Carlos Maurício Fontes Vieira
Keyword(s):  
Mechanical Properties ◽  
Water Absorption ◽  
Physical And Mechanical Properties ◽  
Linear Shrinkage ◽  
Mechanical Tests ◽  
Coffee Plant ◽  
Steel Mold ◽  
Calcium Magnesium ◽  
Potassium Oxides ◽  
Density Linear

This work has as its objective to evaluate effect of the incorporation of an ash, obtained from burning wood from coffee plant, in the physical and mechanical properties of incorporated clayey ceramic. The ash has undergone characterization tests by the techniques of XRF, DTA / TG and XRD. Formulations were prepared with 5, 10, 20 and 30 wt% of ash incorporated into clay bodies that were then homogenized, dried and finally moistened. Rectangular test specimens were prepared by uniaxial pressing in a steel mold at 20 MPa, followed by firing at 700 °C. The fired ceramics were subjected to physical and mechanical tests for determining the bulk density, linear shrinkage, water absorption and tensile strength. The results indicate that the ash is composed predominantly of calcium, magnesium and potassium oxides. The incorporation of ash up to 20 wt% decreased the water absorption and notably increased the ceramic mechanical strength in the temperature investigated.

scholarly journals Preparation and performance of modified montmorillonite-reinforced wood-based foamed composites

BioResources ◽  
2020 ◽  
Vol 15 (2) ◽  
pp. 3566-3584
Author(s):  
Qingde Li ◽  
Yingyi Liang ◽  
Feng Chen ◽  
Tonghui Sang
Keyword(s):  
Mechanical Properties ◽  
Water Absorption ◽  
Flexural Modulus ◽  
Wood Fiber ◽  
Physical And Mechanical Properties ◽  
Thickness Swelling ◽  
Compression Process ◽  
Hygroscopic Properties ◽  
Bonding Effect ◽  
And Performance

Wood fiber was modified by impulse-cyclone drying treatment with poplar and montmorillonite as reinforcing materials; mMMT/polypropylene/wood fiber foaming composite was prepared by the hot compression process. The effects of modification, temperature, and content of montmorillonite on physical and mechanical properties of the composite were analyzed. Mechanical properties, porosity, shrinkage, water absorption, and thickness swelling tests showed that when mMMT reinforcement was 5 wt%, the best performance was achieved. The scanning electron microscopy observations showed that bubble holes were distributed widely and evenly, and mMMT appeared in the cell gap and was encapsulated by polypropylene, which maximized the bonding effect. Flexural strength was 27.5 MPa, flexural modulus was 2110 MPa, tensile strength was 20.0 MPa, and impact strength was 6.30 KJ/m2. When absolute volume of dense solid reached 70.8 cm3, porosity was 21.4% and shrinkage was 1.17%, which indicated that the water absorption increased most remarkably under that test condition. When equilibrium water absorption reached 9.28%, the thickness swelling decreased by 25%. The results showed that mMMT effectively optimized mechanical properties of wood-based foamed composites and improved hygroscopic properties.

scholarly journals Effects of Different Types of Fibers on the Physical and Mechanical Properties of MICP-Treated Calcareous Sand

Materials ◽  
2021 ◽  
Vol 14 (2) ◽  
pp. 268
Author(s):  
Jitong Zhao ◽  
Huawei Tong ◽  
Yi Shan ◽  
Jie Yuan ◽  
Qiuwang Peng ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Water Absorption ◽  
Glass Fiber ◽  
Physical And Mechanical Properties ◽  
Polyester Fiber ◽  
Engineering Properties ◽  
Fiber Types ◽  
Calcite Precipitation ◽  
Calcareous Sand ◽  
Hemp Fiber

Microbial-induced calcite precipitation (MICP) has been a promising method to improve geotechnical engineering properties through the precipitation of calcium carbonate (CaCO3) on the contact and surface of soil particles in recent years. In the present experiment, water absorption and unconfined compressive strength (UCS) tests were carried out to investigate the effects of three different fiber types (glass fiber, polyester fiber, and hemp fiber) on the physical and mechanical properties of MICP-treated calcareous sand. The fibers used were at 0%, 0.10%, 0.15%, 0.20%, 0.25%, 0.30%, 0.35%, and 0.40% relative to the weight of the sand. The results showed that the failure strain and ductility of the samples could be improved by adding fibers. Compared to biocemented sand (BS), the water absorption of these three fiber-reinforced biocemented sands were, respectively, decreased by 11.60%, 21.18%, and 7.29%. UCS was, respectively, increased by 24.20%, 60.76%, and 6.40%. Polyester fiber produced the best effect, followed by glass fiber and hemp fiber. The optimum contents of glass fiber and polyester fiber were 0.20% and 0.25%, respectively. The optimum content of hemp fiber was within the range of 0.20–0.25%. Light-emitting diode (LED) microscope and scanning electron microscope (SEM) images lead to the conclusion that only a little calcite precipitation had occurred around the hemp fiber, leading to a poor bonding effect compared to the glass and polyester fibers. It was therefore suggested that polyester fiber should be used to improve the properties of biocemented sand.

Mechanical properties and toughening mechanisms of epoxy/graphene nanocomposites

2015 ◽  
Vol 35 (3) ◽  
pp. 257-266 ◽  
Author(s):  
Rahim Eqra ◽  
Kamal Janghorban ◽  
Habib Daneshmanesh
Keyword(s):  
Mechanical Properties ◽  
Fracture Surface ◽  
Flexural Strength ◽  
Young’S Modulus ◽  
Young's Modulus ◽  
Graphene Nanosheets ◽  
Flexural Modulus ◽  
Mechanical Tests ◽  
Toughening Mechanism ◽  
Graphene Nanocomposites

Abstract Because of extraordinary physical, chemical and mechanical properties, graphene nanosheets (GNS) are suitable fillers for optimizing the properties of different polymers. In this research, the effect of GNS content (up to 1 wt.%) on tensile and flexural properties, morphology of fracture surface, and toughening mechanism of epoxy were investigated. Results of mechanical tests showed a peak for tensile and flexural strength of samples with 0.1 wt.% GNS such that the tensile and flexural strength improved by 13% and 3.3%, respectively. The Young’s modulus and flexural modulus increased linearly with GNS content, although the behavior of the Young’s modulus was more remarkable. Morphological investigations confirmed this behavior because the GNS dispersion in the epoxy matrix was uniform at lower contents and agglomerated at higher contents. Finally, microscopical observation showed that the major toughening mechanism of graphene-epoxy nanocomposites was crack path deflection, which changed the mirror fracture surface of the pure epoxy to rough surface.

Preparation of ZrO2 Composite Ceramics with High Thermal Shock Resistance

2012 ◽  
Vol 455-456 ◽  
pp. 650-654 ◽  
Author(s):  
He Yi Ge ◽  
Jian Ye Liu ◽  
Xian Qin Hou ◽  
Dong Zhi Wang
Keyword(s):  
Mechanical Properties ◽  
Water Absorption ◽  
Thermal Shock ◽  
Thermal Shock Resistance ◽  
Sintering Temperature ◽  
Fiber Composite ◽  
Physical And Mechanical Properties ◽  
Composite Ceramics ◽  
Shock Resistance ◽  
Absorption Measurements

The physical and mechanical properties of nanometer ZrO2-ZrO2fiber composite ceramics were studied by introduction of ZrO2fiber. ZrO2composite ceramics at different sintering temperature was investigated by porosity and water absorption measurements, flexual strength and thermal shock resistance analysis. Results showed that ZrO2composite ceramics containing 15 wt% ZrO2fiber with sintering temperature of 1650°C exhibited good mechanical properties and thermal shock resistance. The porosity and the water absorption were 8.84% and 1.62%, respectively. The flexual strength was 975 MPa and the thermal shock times reached 31 times. Scanning electron microscope (SEM) was used to analyze the microstructure of ZrO2composite ceramics.

scholarly journals ADSORPTION OF NANOWOLLASTONITE ON CELLULOSE SURFACE: EFFECTS ON PHYSICAL AND MECHANICAL PROPERTIES OF MEDIUM-DENSITY FIBERBOARD (MDF)

CERNE ◽  
2016 ◽  
Vol 22 (2) ◽  
pp. 215-222 ◽  
Author(s):  
Hamid Reza Taghiyari ◽  
Roya Majidi ◽  
Asghar Jahangiri
Keyword(s):  
Mechanical Properties ◽  
Density Functional ◽  
Medium Density Fiberboard ◽  
Physical And Mechanical Properties ◽  
Mechanical Tests ◽  
National Standard ◽  
Medium Density ◽  
Wood Fibers ◽  
Strong Adsorption ◽  
Cellulose Surface

ABSTRACT Effects of nanowollastonite (NW) adsorption on cellulose surface were studied on physical and mechanical properties of medium-density fiberboard (MDF) panels; properties were then compared with those of MDF panels without NW-content. The size range of NW was 30-110 nm. The interaction between NW and cellulose was investigated using density functional theory (DFT). Physical and mechanical tests were carried out in accordance with the Iranian National Standard ISIRI 9044 PB Type P2 (compatible with ASTM D1037-99) specifications. Results of DFT simulations showed strong adsorption of NW on cellulose surface. Moreover, mechanical properties demonstrated significant improvement. The improvement was attributed to the strong adsorption of NW on cellulose surface predicted by DFT, adding to the strength and integrity between wood fibers in NW-MDF panels. It was concluded that NW would improve mechanical properties in MDF panels as a wood-composite material, as well as being effective in improving its biological and thermal conductivity.

scholarly journals Determination of Physical and Mechanical Properties of Three-layer Boards of Teak (Tectona grandis), Seike (Cedrelinga catenaeformis) and Mascarey (Hieronima alchorneoides), Company PISMADE S.A., Riobamba Canton, Chimborazo Province

2021 ◽  
Author(s):  
J. Criollo Barahona ◽  
D. Román Robalino ◽  
E. Cabezas ◽  
E. Salazar Castañeda
Keyword(s):  
Mechanical Properties ◽  
Compression Test ◽  
Physical And Mechanical Properties ◽  
Tectona Grandis ◽  
Mechanical Tests ◽  
Hyeronima Alchorneoides ◽  
Commercial Use ◽  
Palabras Clave ◽  
Thickness Measurements

The present investigation aims to determine the physical and mechanical properties in three-layer boards of Teak (Tectona grandis), Seike (Cedrelinga catenaeformis) and Mascarey (Hieronima alchorneoides), from the PISMADE S.A. Company, Canton Riobamba, province of Chimborazo. The three specimens used for each of the species in each of the tests performed were worked on using the ASTM D143-94 standard for the tests of parallel compression, perpendicular compression and flexion, and the DIN-52182 standard, with the main variation in thickness measurements caused by the commercial use established by the company. Mechanical tests showed that Seike had the best results, being superior in two tests: perpendicular compression and flexion. Teak tests gave us results that were superior in the perpendicular compression test. Mascarey, unlike the two species mentioned above, had complications during the trials due to problems with the glue between layers. Keywords: physical and mechanical properties of wood, three-layer boards. Resumen La presente investigación pretende: Determinar las propiedades físicas y mecánicas en tableros tricapa de Teca, Seike (Cedrelinga catenaeformis) y Mascarey (Hyeronima alchorneoides), Empresa PISMADE S.A., cantón Riobamba, provincia de Chimborazo; para lo cual se utilizaron 3 probetas por cada una de las especies en cada uno de los ensayos realizados, las mismas fueron trabajadas con base a la Norma ASTM D143-94 para las pruebas de compresión paralela, compresión perpendicular y flexión y la Norma DIN-52182, teniendo como principal variación en las medidas de espesor debido al uso comercial establecido por la empresa. Las pruebas mecánicas mostraron que Seike tuvo los mejores resultados al ser superior en dos ensayos: Compresión perpendicular y flexión. Los ensayos con Teca nos dieron como resultados que es superior en el ensayo de compresión perpendicular. Mascarey a diferencia de las dos especies mencionadas anteriormente tuvo complicaciones con los ensayos debido a problemas con el pegamento entre capas. Palabras clave: propiedades físicas y mecánicas de la madera, tableros tricapa.

An attempt to use „Tetra Pak” waste material in particleboard technology

2021 ◽  
Vol 114 ◽  
pp. 70-75
Author(s):  
Radosław Auriga ◽  
Piotr Borysiuk ◽  
Alicja Auriga
Keyword(s):  
Mechanical Properties ◽  
Water Absorption ◽  
Bending Strength ◽  
Physical And Mechanical Properties ◽  
Core Layer ◽  
Waste Material ◽  
Thickness Swelling ◽  
The Core ◽  
Tetra Pak ◽  
The Impact

An attempt to use „Tetra Pak” waste material in particleboard technology. The study investigates the effect of addition Tetra Pak waste material in the core layer on physical and mechanical properties of chipboard. Three-layer chipboards with a thickness of 16 mm and a density of 650 kg / m3 were manufactured. The share of Tetra Pak waste material in the boards was varied: 0%, 5%, 10% and 25%. The density profile was measured to determine the impact of Tetra Pak share on the density distribution. In addition, the manufactured boards were tested for strength (MOR, MOE, IB), thickness swelling and water absorption after immersion in water for 2 and 24 hours. The tests revealed that Tetra Pak share does not affect significantly the value of static bending strength and modulus of elasticity of the chipboard, but it significantly decreases IB. Also, it has been found that Tetra Pak insignificantly decreases the value of swelling and water absorption of the chipboards.

scholarly journals Thermal Action on Normal and High Strength Cement Mortars

2020 ◽  
Vol 10 (18) ◽  
pp. 6455
Author(s):  
Marianela Ripani ◽  
Hernán Xargay ◽  
Ignacio Iriarte ◽  
Kevin Bernardo ◽  
Antonio Caggiano ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Water Absorption ◽  
Peak Load ◽  
Physical And Mechanical Properties ◽  
Thermal Action ◽  
High Strength ◽  
Strength Loss ◽  
Brittle Behavior ◽  
Cement Mortars ◽  
Water Absorption Test

High temperature effect on cement-based composites, such as concrete or mortars, represents one of the most important damaging process that may drastically affect the mechanical and durability characteristics of structures. In this paper, the results of an experimental campaign on cement mortars submitted to high temperatures are reported and discussed. Particularly, two mixtures (i.e., Normal (MNS) and High Strength Mortar (MHS)) having different water-to-binder ratios were designed and evaluated in order to investigate the incidence of both the mortar composition and the effects of thermal treatments on their physical and mechanical properties. Mortar specimens were thermally treated in an electrical furnace, being submitted to the action of temperatures ranging from 100 to 600 °C. After that and for each mortar quality and considered temperature, including the room temperature case of 20 °C, water absorption was measured by following a capillary water absorption test. Furthermore, uniaxial compression, splitting tensile and three-points bending tests were performed under residual conditions. A comparative analysis of the progressive damage caused by temperature on physical and mechanical properties of the considered mortars types is presented. On one hand, increasing temperatures produced increasing water absorption coefficients, evidencing the effect of thermal damages which may cause an increase in the mortars accessible porosity. However, under these circumstances, the internal porosity structure of lower w/b ratio mixtures results much more thermally-damaged than those of MNS. On the other hand, strengths suffered a progressive degradation due to temperature rises. While at low to medium temperatures, strength loss resulted similar for both mortar types, at higher temperature, MNS presented a relatively greater strength loss than that of MHS. The action of temperature also caused in all cases a decrease of Young’s Modulus and an increase in the strain corresponding to peak load. However, MHS showed a much more brittle behavior in comparison with that of MNS, for all temperature cases. Finally, the obtained results demonstrated that mortar quality cannot be neglected when the action of temperature is considered, being the final material performance dependent on the physical properties which, in turn, mainly depend on the mixture proportioning.

Sign in / Sign up

Export Citation Format

Share Document