Study on Surface Modification of Mica Pearl Pigment with Stearic Acid

2016 ◽  
Vol 852 ◽  
pp. 774-781
Author(s):  
Qian Yu ◽  
Yong Le Ke ◽  
Xu Kun Tan ◽  
Gao Dan Luo ◽  
Sheng Bo Han ◽  
...  
Keyword(s):  
Fourier Transform ◽  
Surface Modification ◽  
Stearic Acid ◽  
X Ray ◽  
Electrostatic Spraying ◽  
Ft Ir ◽  
Powder Spraying ◽  
Scanning Electron ◽  
Effect Of Surface ◽  
Ft Ir Spectroscopy

Using stearic acid as modifier, the surface of mica pearl pigment organic modification technology are discussed in this paper, and the application effect of after modified. X-ray powder diffraction (XRD), Fourier transform infrared (FT-IR) spectroscopy and Scanning electron microscope (SEM) were used to characterize the effect of surface modification. Electrostatic spraying test (EST) and Chromatism test were used to characterize the application effect of after modified. The results showed that the stearic acid could be successfully grafted on the surface of mica pearl pigment and enhanced hydrophobicity. Besides, it was demonstrated that the mica pearl pigment treated with stearic acid could make the value of chromatism deviation are low, which also could significantly improve the powder spraying ratio at low spray voltages.

scholarly journals Ciprofloxacin Based on Carrier Double Layered Hydroxide Nano-particles of Fe+3/Fe+2, Fe+3/Ni+2, Al+3/Fe+2, and Al+3/Ni+2 Ions

2020 ◽  
Vol 10 (01) ◽  
pp. 119-126
Author(s):  
Noor M. Mohammed ◽  
Farah AH. Kadhim ◽  
Aseel A. Hammood ◽  
Ashour H. Dawood
Keyword(s):  
Fourier Transform ◽  
Electron Microscope ◽  
Nano Particles ◽  
X Ray Diffraction ◽  
X Ray ◽  
Atomic Force ◽  
Ft Ir ◽  
Double Layered Hydroxide ◽  
Scanning Electron ◽  
Ft Ir Spectroscopy

The double-layered hydroxide nano-particles compounds with ciprofloxacin drug were carried out by preparation of the double layered hydroxide (DLH) of M+3/M+2 ions for selective ions. The ciprofloxacin drug was inserted between them. The resulted compounds were characterized by X-Ray diffraction (XRD), scanning electron microscope (SEM), atomic force microscope (AFM), and Fourier Transform Infrared (FT-IR) spectroscopy; the antibacterial studied done by using the gram (+) and gram (-) pigments.

Delamination of Kaolinite by Intercalation of Urea Using Milling

2017 ◽  
Vol 888 ◽  
pp. 136-140 ◽  
Author(s):  
Suzi Salwah Jikan ◽  
Nur Azam Badarulzaman ◽  
Shehu Yahaya ◽  
Ajiya Dahiru Adamu
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Fourier Transform ◽  
Ir Spectroscopy ◽  
Powder Diffraction ◽  
Basal Spacing ◽  
X Ray ◽  
Ft Ir ◽  
Scanning Electron ◽  
Ft Ir Spectroscopy

The effect of milling on structure of kaolinite-urea intercalates were studied. Untreated and treated kaolinite samples were examined by Field scanning electron microscopy (FESEM), X-ray powder diffraction (XRPD) and Fourier transform infrared (FT-IR) spectroscopy. The basal spacing of kaolinite measured by X-ray powder diffraction (XRPD) increased from 1.02 to 3.62 nm after intercalation by urea. Significantly, nature of intercalation was reached through formation of hydrogen bonds between urea and both Si-O and AlOH groups of the interlayer surface of kaolinite.

Study on the Surface Modification of Nano-TiO2

2013 ◽  
Vol 641-642 ◽  
pp. 529-533
Author(s):  
Dong Mei Zhao ◽  
Gui Min Qian ◽  
Shan Yun ◽  
Qian Qian Song ◽  
Dong Hai Zhu ◽  
...  
Keyword(s):  
Surface Modification ◽  
Measuring Instrument ◽  
Optical Contact ◽  
Nano Tio2 ◽  
X Ray ◽  
Transmission Electron ◽  
Angle Measuring ◽  
Ft Ir ◽  
Effect Of Surface ◽  
Ft Ir Spectroscopy

KH550 modified ZnO/TiO2 was prepared. The surface of nano-TiO2 was coated with ZnO derived from Na2Zn(OH)4 via a heterogeneous nucleation process, and coupling agent KH550 was used to treat the surface of ZnO/TiO2. Transmission electron microscopy (TEM), X-ray powder diffraction (XRD), Fourier transform infrared (FT-IR) spectroscopy and Optical contact angle measuring instrument were used to characterize the effect of surface modification. The results showed that the surface of nano-TiO2 was coated by ZnO nanoparticles; After modified by the KH550, the modified ZnO/TiO2 showed better dispersion in water-toluene solution; and the surface of modified ZnO/TiO2 became more hydrophobic-lipophilic than that of modified uncoated nano-TiO2.

scholarly journals Two-Step Separation of Chitin from Shrimp Shells Using Citric Acid and Deep Eutectic Solvents with the Assistance of Microwave

Polymers ◽  
2019 ◽  
Vol 11 (3) ◽  
pp. 409 ◽  
Author(s):  
Dandan Zhao ◽  
Wen-Can Huang ◽  
Na Guo ◽  
Shuye Zhang ◽  
Changhu Xue ◽  
...  
Keyword(s):  
Citric Acid ◽  
Deep Eutectic Solvents ◽  
Second Step ◽  
X Ray Diffraction ◽  
X Ray ◽  
Shrimp Shells ◽  
Ft Ir ◽  
Scanning Electron ◽  
Ft Ir Spectroscopy

In this research, a two-step extraction approach was developed for chitin preparation from shrimp shells by utilizing citric acids and deep eutectic solvents (DESs), which effectively removed minerals and proteins. In the first step, minerals of shrimp shells were removed by citric acid, and the demineralization efficiency reached more than 98%. In the second step, the removal of protein was carried out using deep eutectic solvents with the assistance of microwave, and the deproteinization efficiency was more than 88%. The results of scanning electron microscopy (SEM), Fourier transform infrared (FT-IR) spectroscopy, X-ray diffraction analysis (XRD), and thermogravimetric analysis (TGA) showed that the quality of DES-prepared chitin was comparable to that of traditional acid/alkali-prepared chitin. These results were realized without utilizing hazardous chemicals, which are detrimental to the environment. This research indicates that a DES-based preparation approach has the potential for application in the recovery of biopolymers from natural resources.

scholarly journals Crosslinked sulfonated polyacrylamide (Cross-PAA-SO3H) tethered to nano-Fe3O4 as a superior catalyst for the synthesis of 1,3-thiazoles

BMC Chemistry ◽  
2019 ◽  
Vol 13 (1) ◽  
Author(s):  
Hossein Shahbazi-Alavi ◽  
Sheida Khojasteh-Khosro ◽  
Javad Safaei-Ghomi ◽  
Maryam Tavazo
Keyword(s):  
Fourier Transform ◽  
Phenacyl Bromide ◽  
Vibrating Sample Magnetometer ◽  
Synthetic Route ◽  
One Pot ◽  
X Ray ◽  
Ft Ir ◽  
Sulfonated Polyacrylamide ◽  
Nano Fe3o4 ◽  
Scanning Electron

Abstract Crosslinked sulfonated polyacrylamide (Cross-PAA-SO3H) attached to nano-Fe3O4 as a superior catalyst has been used for the synthesis of 3-alkyl-4-phenyl-1,3-thiazole-2(3H)-thione derivatives through a three-component reactions of phenacyl bromide or 4-methoxyphenacyl bromide, carbon disulfide and primary amine under reflux condition in ethanol. A proper, atom-economical, straightforward one-pot multicomponent synthetic route for the synthesis of 1,3-thiazoles in good yields has been devised using crosslinked sulfonated polyacrylamide (Cross-PAA-SO3H) tethered to nano-Fe3O4. The catalyst has been characterized by Fourier-transform infrared spectroscopy (FT-IR), scanning electron microscope (SEM), dynamic light scattering (DLS), X-ray powder diffraction (XRD), energy-dispersive X-ray spectroscopy (EDS), thermogravimetric analysis (TGA) and vibrating-sample magnetometer (VSM).

Synthesis of Fe 3+-Dopped PANI Conductive Nanomaterials via Interfacial Polymerization

2011 ◽  
Vol 239-242 ◽  
pp. 2839-2842
Author(s):  
Hong Mei Mu ◽  
Peng Fei ◽  
Bi Tao Su ◽  
Zi Qiang Lei
Keyword(s):  
Electron Microscopy ◽  
Transmission Electron Microscopy ◽  
Fourier Transform ◽  
Ir Spectroscopy ◽  
Interfacial Polymerization ◽  
X Ray ◽  
Transmission Electron ◽  
Ft Ir ◽  
Conductive Nanomaterials ◽  
Ft Ir Spectroscopy

A series of Fe3+-dopped polyaniline (Fe3+/PANI) nanomaterials with different morphologies and a higher conductivity were successfully synthesized using a simple and static interfacial polymerization by using FeCl3 as both oxidant catalyst and dopant. The effect of surfactants CTAB and SDS and the concentration of FeCl3 on the morphology and conductivity of Fe3+/PANI nanomaterial were investigated. The samples were characterized by Transmission Electron Microscopy (TEM), SDY-4 probes conductivity meter, X-ray Diffractometry (XRD), Energy dispersive spectroscopy (EDS) and Fourier transform infrared (FT-IR) spectroscopy techniques. TEM’s results showed that their morphologies changed with the type of the surfactant and the concentration of FeCl3. Introducing surfactants CTAB and SDS into Fe3+/PANI remarkably improved the conductivity of the material. The conductivities of CTAB/Fe3+/PANI and SDS /Fe3+/PANI nanomaterials were respectively about 4.8×10-2 and 1.3×10-2 S/cm while the conductivity of Fe3+/PANI was found to be 1.5×10-4 S/cm. The different morphology and high conductivity may be ascribed to the mutual effects of the surfactant and oxidant.

Structural and Optical Study of Chemically Synthesized Polyaniline

2015 ◽  
Vol 7 (1) ◽  
Author(s):  
R. K. Shukla ◽  
Susheel Kumar Singh ◽  
Akhilesh Tripathi
Keyword(s):  
Fourier Transform ◽  
Oxidative Polymerization ◽  
Ultra Violet ◽  
Optical Study ◽  
X Ray Diffraction ◽  
Chemical Oxidative Polymerization ◽  
X Ray ◽  
Ft Ir ◽  
Polymerization Method ◽  
Scanning Electron

Polyaniline (PANI) is synthesized by chemical oxidative polymerization method. The, characterization were made using XRD (X-ray diffraction), FT-IR (Fourier transform spectroscopy), UV -vis (ultra-violet visible spectrophotometer) technique which confirms the synthesis of the Polyaniline. The surface morphology of Polyaniline was studied with scanning electron microscope (SEM).

Synthesis of Triethynylborazine-Polyhydromethylsiloxane Copolymers and its Ceramization

2013 ◽  
Vol 774-776 ◽  
pp. 629-633
Author(s):  
Ji Feng Jiang ◽  
Kang Kang Guo ◽  
Ya Ping Zhu ◽  
Fan Wang ◽  
Hui Min Qi
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Nuclear Magnetic Resonance ◽  
Fourier Transform ◽  
Thermogravimetric Analysis ◽  
X Ray Diffraction ◽  
Hydrosilylation Reaction ◽  
X Ray ◽  
Ft Ir ◽  
Scanning Electron

Triethynylborazine-polyhydromethylsiloxane copolymers (TEB-PHMSs) were prepared through hydrosilylation reaction between -C≡CH attached to boron and ≡Si-H. The structures of TEB-PHMSs were characterized by Fourier transform Infrared (FT-IR) and Nuclear Magnetic Resonance (NMR) spectroscopy. Their cure behavior were examined by Differential Scanning Calorimeter (DSC) and FT-IR, and then thermostability and ceramization of cured TEB-PHMS were investigated by Thermogravimetric analysis (TGA), pyrolysis-GC-MS, X-ray diffraction (XRD) and Scanning Electron Microscopy (SEM). The results indicated that TEB-PHMSs could be cured and converted into an outstanding thermostable SiBCN ceramics.

Preparation of Polyaniline/SiO2 Composites by Modified Silica Using Succinic Acid

2012 ◽  
Vol 535-537 ◽  
pp. 149-153 ◽  
Author(s):  
Er Yuan Li ◽  
Xiu Feng Wang ◽  
Xue Zhi Wang ◽  
Hao Wang
Keyword(s):  
Thermal Stability ◽  
Succinic Acid ◽  
X Ray Diffraction ◽  
Modified Silica ◽  
X Ray ◽  
Surface Character ◽  
Ft Ir ◽  
Thermal Stability Of ◽  
Scanning Electron ◽  
Ft Ir Spectroscopy

Polyaniline/SiO2 composites were prepared by the SiO2 particles whose surface character was modified by succinic acid. The composites were characterized by Fourier transform infrared (FT–IR) spectroscopy, X–ray diffraction (XRD), thermogravimetric analysis (TGA), scanning electron microscope (SEM). The results demonstrated that the thermal stability of PANI had improved.

scholarly journals SINTESIS DAN KARAKTERISASI N DOPED TiO2 (N/TiO2) NANOTUBE SERTA UJI AKTIVITAS FOTOKATALISIS TERHADAP ZAT WARNA RHODAMIN B

2021 ◽  
Vol 19 (1) ◽  
pp. 27-32
Author(s):  
Ida Nur Apriani Apriani ◽  
Jarnuzi Gunlazuardi
Keyword(s):  
Fourier Transform ◽  
Tio2 Nanotube ◽  
X Ray Diffraction ◽  
Linear Sweep ◽  
Doped Tio2 ◽  
X Ray ◽  
Infra Red ◽  
Ft Ir ◽  
Rhodamin B ◽  
Scanning Electron

Telah dilakukan sintesis fotokatalis N/TiO2 bermofologi nanotube dengan metode anodisasi  menggunakan ammonium nitrat (NH4NO3) sebagai sumber dopan pada berbagai variasi konsentrasi (0,5M , 1M, 2M), dilanjutkan dengan kalisinasi pada suhu 4500C selama 2 jam untuk mendapatkan fasa kristal anatase. Karakterisasi dilakukan menggunakan Scanning Electron Miscroscopy (SEM), Fourier Transform Infra Red (FT-IR), X-ray Diffraction (XRD), dan DRS (Diffused Reflectant Spectrometry) UV-Vis. Pengujian Linear Sweep Voltametri dan Multi Pulse Anperiometri pada fotokatalis­ N/TiO2 telah berhasil diterapkan untuk degradasi senyawa Rhodamin B menggunakan sinar UV maupun sinar tampak. Aplikasi dari uji fotoelektrokatalisis menggunakan sinar tampak untuk N/TiO2-NT memberikan hasil eliminasi sebesar 47,86%, sedangkan bila menggunakan TiO2 nanotube tanpa dopan eleminasi hanya sebesar 25,49%. Hal ini menunjukkan bahwa proses doping yang dilakukan telah berhasil menyisipkan nitrogen kedalam matrik TiO2 nanotube dan memperbaiki kinerja fotokatalisis nya di daerah sinar tampak.

Sign in / Sign up

Export Citation Format

Share Document