Interfacial Tension Measurement of Light Oil from Thailand to Enhance Oil Recovery for Surfactant Flooding Application

2017 ◽  
Vol 890 ◽  
pp. 235-238 ◽  
Author(s):  
Chitipat Chuaicham ◽  
Kreangkrai Maneeintr
Keyword(s):  
Interfacial Tension ◽  
Enhanced Oil Recovery ◽  
Oil Recovery ◽  
Surfactant Concentration ◽  
High Salinity ◽  
Surfactant Flooding ◽  
Sodium Dodecylbenzenesulfonate ◽  
The North ◽  
Light Oil ◽  
Enhance Oil Recovery

To enhance oil recovery, surfactant flooding is one of the techniques used to reduce the interfacial tension (IFT) between displacing and displaced phases in order to maximize productivity. Due to high salinity of crude oil in the North of Thailand, surfactant flooding is a suitable choice to perform enhanced oil recovery. The objective of this work is to measure the IFT and observe the effects of parameters such as pressure, temperature, concentration and salinity on IFT reduction. In this study, sodium dodecylbenzenesulfonate is used as surfactant to reduce IFT. The results show that the major factor affecting reduction of IFT is surfactant concentration accounting for 98.1%. IFT reduces with the increase of salinity up to 86.3% and up to 9.6% for temperature. However, pressure has less effect on IFT reduction. The results of this work can apply to increase oil production in the oilfield in the North of Thailand.

scholarly journals An Experimental Approach to Formulate Lignin-Based Surfactant for Enhanced Oil Recovery

2019 ◽  
Vol 2019 ◽  
pp. 1-6 ◽  
Author(s):  
Kenny Ganie ◽  
Muhammad A Manan ◽  
Arif Ibrahim ◽  
Ahmad Kamal Idris
Keyword(s):  
Interfacial Tension ◽  
Enhanced Oil Recovery ◽  
Oil Recovery ◽  
Glass Beads ◽  
Sodium Dodecylbenzenesulfonate ◽  
Active Concentration ◽  
Displacement Experiments ◽  
Amine System ◽  
Lignin Amine ◽  
The Cost

The higher cost of chemical surfactants has been one of the main reasons for their limited used in enhanced oil recovery (EOR) process. Hence, the reason for developing lignin-based surfactant is to lower the cost of chemicals as it does not tie to the price of crude oil as compared to petroleum-based surfactants. Besides, lignin is biodegradable and easily extracted from plant waste. The objectives of this study are to determine the formulations of the lignin-based surfactant for EOR applications and to determine the oil recovery performance of the formulated surfactants through surfactant flooding. The lignin-based surfactants were formulated by mixing the lignin with the amine (polyacrylamide or hexamethylenetetramine) and the surfactant sodium dodecylbenzenesulfonate in a 20,000 ppm NaCl brine. Interfacial tension (IFT) of the formulated lignin-based surfactant is measured at ambient temperature using the spinning drop method. The displacement experiments were conducted at room temperature in glass beads pack holders filled with glass beads, saturated with paraffin and brine. The results of the study showed that the best formulation of lignin-based surfactant is using hexamethylenetetramine as the amine, lignin, and sodium dodecylbenzenesulfonate at 2% total active concentration. The oil recovery and interfacial tension using the lignin amine system is comparable with the commercial petroleum sulfonate system.

scholarly journals Experimental Investigation of Surfactant Partitioning in Pre-CMC and Post-CMC Regimes for Enhanced Oil Recovery Application

Energies ◽  
2019 ◽  
Vol 12 (12) ◽  
pp. 2319 ◽  
Author(s):  
Ahmed Fatih Belhaj ◽  
Khaled Abdalla Elraies ◽  
Mohamad Sahban Alnarabiji ◽  
Juhairi Aris B M Shuhli ◽  
Syed Mohammad Mahmood ◽  
...  
Keyword(s):  
Surface Tension ◽  
High Temperature ◽  
Interfacial Tension ◽  
Enhanced Oil Recovery ◽  
Oil Recovery ◽  
High Performance ◽  
Surfactant Concentration ◽  
Effect Of Temperature ◽  
Sweep Efficiency ◽  
Partitioning Coefficient

The applications of surfactants in Enhanced Oil Recovery (EOR) have received more attention in the past decade due to their ability to enhance microscopic sweep efficiency by reducing oil-water interfacial tension in order to mobilize trapped oil. Surfactants can partition in both water and oil systems depending on their solubility in both phases. The partitioning coefficient (Kp) is a key parameter when it comes to describing the ratio between the concentration of the surfactant in the oil phase and the water phase at equilibrium. In this paper, surfactant partitioning of the nonionic surfactant Alkylpolyglucoside (APG) was investigated in pre-critical micelle concentration (CMC) and post-cmc regimes at 80 °C to 106 °C. The Kp was then obtained by measuring the surfactant concentration after equilibration with oil in pre-cmc and post-cmc regimes, which was done using surface tension measurements and high-performance liquid chromatography (HPLC), respectively. Surface tension (ST) and interfacial tension (IFT) behaviors were investigated by performing pendant and spinning drop tests, respectively—both tests were conducted at high temperatures. From this study, it was found that APG was able to lower IFT as well as ST between water/oil and air/oil, and its effect was found to be more profound at high temperature. The partitioning test results for APG in pre-cmc and post-cmc regimes were found to be dependent on the surfactant concentration and temperature. The partitioning coefficient is directly proportional to IFT, where at high partitioning intensity, IFT was found to be very low and vice versa at low partitioning intensity. The effect of temperature on the partitioning in pre-cmc and post-cmc regimes had the same impact, where at a high temperature, additional partitioned surfactant molecules arise at the water-oil interface as the association of molecules becomes easier.

Investigation of Reduced Interfacial Tension by Surfactant Flooding in Mixed-Wet Reservoirs

2021 ◽  
Author(s):  
Usman Aslam
Keyword(s):  
Interfacial Tension ◽  
Capillary Pressure ◽  
Enhanced Oil Recovery ◽  
Relative Permeability ◽  
Oil Recovery ◽  
Simulation Studies ◽  
Surfactant Flooding ◽  
Gravity Segregation ◽  
Simulation Results ◽  
Capillary Pressure Curves

Abstract Surfactant flooding has long been considered a reliable solution for enhanced oil recovery, either by reducing oil-water interfacial tension (IFT) or through wettability alteration. This paper reveals the effect that reduced IFT has on capillary trapping in heterogeneous reservoirs. This effect is investigated through various numerical experiments on different simulation models where rock capillary pressure is assumed to scale with IFT. Capillary contrast on the scale of a few centimeters to a few tens of meters is reduced in the presence of surfactants. This reduction in IFT, under very specific circumstances, creates favorable conditions for increased or accelerated hydrocarbon production from mixed-wet reservoirs. The focus of this study is to ascertain the effectiveness of surfactant flooding in mixed-wet reservoirs. Simulation studies of different mechanisms which are believed to occur in mixed-wet reservoirs are presented. Simulation results indicate the promising effect of surfactant flooding on oil recovery, depending on the type of reservoir. Detailed fine-scale simulation studies are carried out with representative relative permeability and imbibition capillary pressure curves from mixed-wet cores. By designing and selecting a series of surfactants to lower the IFT to the range of 10-3dynes/cm, a recovery of 10 to 20% of the original oil-in-place is technically and economically feasible. The efficiency of surfactant flooding is investigated through sensitivity scenarios on formation rock/fluid parameters, including permeability, interfacial tension, rate flow, etc. Geological heterogeneity (layering and heterogeneous inclusions), imbibition capillary pressure curves, viscous/capillary balance (Nc), and gravitational forces were all found to have an impact on recovery by surfactant flooding. Numerical model dimensions, permeability, IFT, density contrast between oil and water, and injection flow rates were found to be the critical parameters influencing simulation results. Gravity segregation, typically ignored in earlier studies, was found to have a significant effect on reservoir performance. Two different numerical models, with and without impermeable shale streaks, were used to capture the gravity segregation effect. The results revealed that the reduction in interfacial tension helps gravity to segregate oil and water, ultimately resulting in improved oil recovery. Moreover, results from the numerical simulation studies revealed that either an inexpensive or a good quality surfactant at low concentration can be used to obtain the same enhanced oil recovery. The effect of change in oil relative permeability curvature, due to reduced interfacial tension, also revealed a reduction in the remaining oil saturation with an increase in the capillary number.

Experimental Study on Low Interfacial Tension Foam for Enhanced Oil Recovery in High-Temperature and High-Salinity Reservoirs

2017 ◽  
Vol 31 (12) ◽  
pp. 13416-13426 ◽  
Author(s):  
Jiaping Tao ◽  
Caili Dai ◽  
Wanli Kang ◽  
Guang Zhao ◽  
Yifei Liu ◽  
...  
Keyword(s):  
Experimental Study ◽  
High Temperature ◽  
Interfacial Tension ◽  
Enhanced Oil Recovery ◽  
Oil Recovery ◽  
High Salinity ◽  
Low Interfacial Tension

Characterization of Surfactant Flooding for Light Oil Using Gum Arabic

2015 ◽  
Vol 21 ◽  
pp. 136-147 ◽  
Author(s):  
Oluwaseun Taiwo ◽  
Kelani Bello ◽  
Ismaila Mohammed ◽  
Olalekan Olafuyi
Keyword(s):  
Interfacial Tension ◽  
Flow Rate ◽  
Oil Recovery ◽  
Surfactant Concentration ◽  
Sodium Dodecyl ◽  
Gum Arabic ◽  
Polymer Flooding ◽  
Water Flooding ◽  
Surfactant Flooding ◽  
Acacia Senegal

Surfactant flooding, a chemical IOR technique is one of the viable EOR processes for recovering additional oil after water flooding. This is because it reduces the interfacial tension between the oil and water and allows trapped oil to be released for mobilization by a polymer.In this research, two sets of experiments were performed. First, the optimum surfactant concentration was determined through surfactant polymer flooding using a range of surfactant concentration of 0.1% to 0.6% and 15% of polymer. Secondly, another set of experiments to determine the optimum flow rate for surfactant flooding was carried out using the optimum surfactant concentration obtained. Lauryl Sulphate (Sodium Dodecyl Sulphate, SDS), an anionic surfactant, was used to alter the interfacial tension and reduce capillary pressure while Gum Arabic, an organic adhesive gotten from the hardened sap of the Acacia Senegal and Acacia Seyal trees, having a similar molecular structure and chemical characteristics with Xanthan Gum, was the polymer used to mobilize the oil.The results show that above 0.5%, oil recovery decreases with increase in concentration such that between 0.5 and 0.6%, a decrease of (20% -19%) is recorded. This suggests that it would be uneconomical to exceed surfactant concentration of 0.5%. It is shown in the result of the first set of experiments that a range of oil recovery of 59% to 76% for water flooding and a range of 11.64% to 20.02% additional oil recovery for surfactant Polymer flooding for a range of surfactant flow rate of surfactant concentration of 0.1% to 0.6%. For the second sets of experiments, a range of oil recovery of 64% to 68% for water flooding and a range of 15% to 24% additional oil recovery for surfactant flooding for a range of surfactant flow rate of surfactant flow rate of 1cc/min to 6cc/min. The Optimum surfactant flow rate resulting in the highest oil recovery for the chosen core size is 3cc/min. It's highly encouraged that the critical displacement rate is maintained to prevent the development of slug fingers.In summary, an optimum Surfactant flow rate is required for better performance of a Surfactant flooding.

scholarly journals Experimental study of combined low salinity and surfactant flooding effect on oil recovery

2020 ◽  
Vol 76 ◽  
pp. 4
Author(s):  
Abdulmecit Araz ◽  
Farad Kamyabi
Keyword(s):  
Interfacial Tension ◽  
Oil Recovery ◽  
High Salinity ◽  
Wettability Alteration ◽  
Moderate Increase ◽  
Surfactant Flooding ◽  
Improved Oil Recovery ◽  
Oil Saturation ◽  
Low Salinity ◽  
Salinity Water

A new generation improved oil recovery methods comes from combining techniques to make the overall process of oil recovery more efficient. One of the most promising methods is combined Low Salinity Surfactant (LSS) flooding. Low salinity brine injection has proven by numerous laboratory core flood experiments to give a moderate increase in oil recovery. Current research shows that this method may be further enhanced by introduction of surfactants optimized for lowsal environment by reducing the interfacial tension. Researchers have suggested different mechanisms in the literature such as pH variation, fines migration, multi-component ionic exchange, interfacial tension reduction and wettability alteration for improved oil recovery during lowsal injection. In this study, surfactant solubility in lowsal brine was examined by bottle test experiments. A series of core displacement experiments was conducted on nine crude oil aged Berea core plugs that were designed to determine the impact of brine composition, wettability alteration, Low Salinity Water (LSW) and LSS flooding on Enhancing Oil Recovery (EOR). Laboratory core flooding experiments were conducted on the samples in a heating cabinet at 60 °C using five different brine compositions with different concentrations of NaCl, CaCl2 and MgCl2. The samples were first reached to initial water saturation, Swi, by injecting connate water (high salinity water). LSW injection followed by LSS flooding performed on the samples to obtain the irreducible oil saturation. The results showed a significant potential of oil recovery with maximum additional recovery of 7% Original Oil in Place (OOIP) by injection of LS water (10% LS brine and 90% distilled water) into water-wet cores compared to high salinity waterflooding. It is also concluded that oil recovery increases as wettability changes from water-wet to neutral-wet regardless of the salinity compositions. A reduction in residual oil saturation, Sor, by 1.1–4.8% occurred for various brine compositions after LSS flooding in tertiary recovery mode. The absence of clay swelling and fine migration has been confirmed by the stable differential pressure recorded for both LSW and LSS flooding. Aging the samples at high temperature prevented the problem of fines production. Combined LSS flooding resulted in an additional oil recovery of 9.2% OOIP when applied after LSW flooding. Surfactants improved the oil recovery by reducing the oil-water interfacial tension. In addition, lowsal environment decreased the surfactant retention, thus led to successful LSS flooding. The results showed that combined LSS flooding may be one of the most promising methods in EOR. This hybrid improved oil recovery method is economically more attractive and feasible compared to separate low salinity waterflooding or surfactant flooding.

Sign in / Sign up

Export Citation Format

Share Document