The Effect of Isothermal Hold Temperature on Microstructure and Mechanical Properties of TRIP Steel

2017 ◽  
Vol 270 ◽  
pp. 253-257 ◽  
Author(s):  
Ludmila Kučerová ◽  
Martin Bystrianský ◽  
Josef Káňa
Keyword(s):  
Mechanical Properties ◽  
Trip Steel ◽  
Retained Austenite ◽  
Mechanical Treatment ◽  
Volume Fraction ◽  
Carbon Steels ◽  
Processing Route ◽  
Isothermal Hold ◽  
Low Carbon ◽  
Thermo Mechanical Treatment

TRIP (transformation induced plasticity) steels are low alloyed low carbon steels with complex microstructures consisting of ferrite, bainite and retained austenite. This complex microstructure provides them with excellent strength to ductility balance, making them a member of advanced high strength steels (AHSS) group. Suitable microstructure can be obtained by either heat or thermo-mechanical treatment. A hold in bainite transformation region is an integral part of any form of commercial TRIP steel processing route, as it enables formation of sufficient volume fraction of bainite and also stabilization of retained austenite in the final microstructure. Various bainitic hold temperatures ranging from 350 °C to 500 °C were tested within thermo-mechanical treatment of 0.2C-1.5Mn-0.6S-1.5Al steel and the final microstructures were evaluated with regard to the suitability to TRIP effect and achieved mechanical properties. The microstructures were analyzed by scanning electron microscopy and mechanical properties measured by tensile test.

Crystallography and Mechanical Properties of Ultrafine TRIP-Aided Multi-Phase Steels

2007 ◽  
Vol 539-543 ◽  
pp. 4351-4356 ◽  
Author(s):  
Masayuki Wakita ◽  
Yoshitaka Adachi ◽  
Yo Tomota
Keyword(s):  
Mechanical Properties ◽  
Retained Austenite ◽  
Volume Fraction ◽  
Large Strain ◽  
High Volume ◽  
Underlying Mechanism ◽  
Carbon Steels ◽  
Diffraction Measurement ◽  
Low Carbon ◽  
Multi Phase

This study aims at examining thermomechanical controlled process to realize ultrafine TRIP-aided multi-phase microstructures in low carbon steels. Heavy deformation at a supercooled austenite region was found to lead the formation of 2 μm ferrite as well as retained austenite with high volume fraction. The morphology of retained austenite was changed from film-like shape to granular shape with lowering finish rolling temperature in austenite field. This ultrafine TRIP-aided multi-phase steel showed good balance of tensile strength with total elongation, ie. 1080MPa and 26.9%. A novel in-situ neutron diffraction measurement demonstrated that the retained granular austenite transformed to martensite at a relatively large strain compared with the retained film austenite. The therein-underlying mechanism of the good mechanical properties was discussed from the view points of the morphological and thermodynamical stabilization of retained austenite.

Isothermal Transformation, Microstructure and Mechanical Properties of Ausformed Low-Carbon Carbide-Free Bainitic Steel

2018 ◽  
Vol 941 ◽  
pp. 329-333 ◽  
Author(s):  
Jiang Ying Meng ◽  
Lei Jie Zhao ◽  
Fan Huang ◽  
Fu Cheng Zhang ◽  
Li He Qian
Keyword(s):  
Mechanical Properties ◽  
Retained Austenite ◽  
Volume Fraction ◽  
Bainitic Ferrite ◽  
Isothermal Transformation ◽  
Bainitic Transformation ◽  
Isothermal Treatment ◽  
Bainitic Steel ◽  
Low Carbon ◽  
Microstructure And Mechanical Properties

In the present study, the effects of ausforming on the bainitic transformation, microstructure and mechanical properties of a low-carbon rich-silicon carbide-free bainitic steel have been investigated. Results show that prior ausforming shortens both the incubation period and finishing time of bainitic transformation during isothermal treatment at a temperature slightly above the Mspoint. The thicknesses of bainitic ferrite laths are reduced appreciably by ausforming; however, ausforming increases the amount of large blocks of retained austenite/martenisite and decreases the volume fraction of retained austenite. And accordingly, ausforming gives rise to significant increases in both yield and tensile strengths, but causes noticeable decreases in ductility and impact toughness.

Study on Microstructures and Mechanical Properties of Cold-Rolled C-Mn-Si-Al TRIP Steel

2010 ◽  
Vol 146-147 ◽  
pp. 678-681
Author(s):  
Zheng You Tang ◽  
Hua Ding
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Trip Steel ◽  
Retained Austenite ◽  
Volume Fraction ◽  
Total Elongation ◽  
Partial Substitution ◽  
Cold Rolled ◽  
Microstructures And Mechanical Properties

The effect of the partial substitution of Si by Al on the microstructures and the mechanical properties of cold rolled C-Mn-Si TRIP steel was investigated. The results show that the partial substitution of Si by Al could refine the microstructures, increase the volume fraction of ferrite and retained austenite. In addition, the excellent mechanical properties of the Al partial substituted TRIP steel could be obtained, the tensile strength, total elongation and strength-ductility of C-Mn-Si-Al TRIP steel are 739MPa, 38% and 28082MPa%, respectively.

Effect of Phosphorus on Microstructure, Mechanical Properties, and Formation of Retained Austenite in TRIP Steels

2012 ◽  
Vol 508 ◽  
pp. 128-132 ◽  
Author(s):  
Eui Pyo Kwon ◽  
Shun Fujieda ◽  
Kozo Shinoda ◽  
Shigeru Suzuki
Keyword(s):  
Mechanical Properties ◽  
Carbon Concentration ◽  
Trip Steel ◽  
Retained Austenite ◽  
Volume Fraction ◽  
Transformation Induced Plasticity ◽  
Trip Steels ◽  
The Stability

In this Study, Influences of P on the Microstructure, Mechanical Properties, and Retained Austenite Characteristics in Transformation Induced Plasticity (TRIP) Steels Were Investigated. Microstructure of 0.2mass%P Containing TRIP Steel Was Inhomogeneous and it Resulted in Deterioration of the Mechanical Properties. Retained Austenite Characteristics such as Volume Fraction and Carbon Concentration Were Also Affected by P. The Stability of Retained Austenite in P Containing TRIP Steel Was Different from that in P-Free TRIP Steel. Such Difference in the Stability of Retained Austenite Was Attributed to the Effect of the Carbon Concentration in Retained Austenite as Well as their Different Microstructure.

scholarly journals Study of the effect of nano-sized precipitates on the mechanical properties of boron-added low-carbon steels by neutron scattering techniques

2008 ◽  
Vol 41 (5) ◽  
pp. 906-912 ◽  
Author(s):  
B. S. Seong ◽  
Y. R. Cho ◽  
E. J. Shin ◽  
S. I. Kim ◽  
S.-H. Choi ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Neutron Scattering ◽  
Volume Fraction ◽  
Weight Fraction ◽  
Ferrite Matrix ◽  
Carbon Steels ◽  
Average Radius ◽  
Boron Addition ◽  
Low Carbon ◽  
Low Carbon Steels

Small-angle neutron scattering (SANS) and neutron powder diffraction (ND) techniques were used to study quantitatively the effect of nano-sized precipitates and boron addition on the mechanical properties of low-carbon steels. SANS was used to evaluate nano-sized precipitates, smaller than about 600 Å in diameter, and ND was used to determine the weight fraction of the cementite precipitates. Fine core–shell structured spherical precipitates with an average radius of ~50 Å, such as MnS and/or CuS, surrounded by BN layers were observed in the boron-added (BA) low-carbon steels; fine spherical precipitates with an average radius of ~48 Å were mainly observed in the boron-free (BF) low-carbon steels. In the BA steels, the number of boron precipitates, such as BN, Fe3(C,B) and MnS, surrounded by BN layers increased drastically at higher hot-rolling temperatures. The volume fraction of the fine precipitates of the BA steels was higher than that of the BF steels; this difference is related to the rapid growth of the BN layers on the MnS and CuS precipitates. Boron addition to low-carbon steels resulted in a reduction in strength and an improvement in elongation; this behaviour is related to the reduction of the solute carbon and the nitrogen contents in the ferrite matrix caused by the precipitation of BN, as well by the increase in the volume fraction of the cementites.

Effect of Annealing Temperature on Austenite Stability of a δ-TRIP Steel

2019 ◽  
Vol 818 ◽  
pp. 82-86
Author(s):  
Xin Xu ◽  
Ren Dong Liu ◽  
Bao Yu Xu ◽  
Hong Liang Yi ◽  
Guo Dong Wang
Keyword(s):  
Mechanical Properties ◽  
Trip Steel ◽  
Retained Austenite ◽  
Annealing Temperature ◽  
Volume Fraction ◽  
X Ray Diffraction ◽  
X Ray ◽  
Austenite Stability ◽  
Poor Stability ◽  
Better Than

In this work, a novel type of δ-TRIP steel was designed, and the content and stability of retained austenite in δ-TRIP specimens under different annealing processes were detected and studied, respectively. The volume fraction of austenite was determined by X-ray diffraction (XRD). The microstructure and mechanical properties were analyzed systematically. The results show that a complex microstructure composed of three phases (ferrite, bainite and retained austenite) was obtained in the δ-TRIP steel. With the increasing of annealing temperature, both retained austenite and bainite content in the specimen increased, while the carbon content in retained austenite decreased, leading to a poor stability for retained austenite. Both tensile and yield strength improved with the increasing of annealing temperature, while the elongation reduced. The feature of retained austenite led to an excellent combination of ductility and strength, which was better than traditional TRIP steel.

scholarly journals Effect of Pre-Quenching Process on Microstructure and Mechanical Properties in a Nb-Microalloyed Low Carbon Q-P Steel

2015 ◽  
Vol 816 ◽  
pp. 729-735 ◽  
Author(s):  
Jun Zhang ◽  
Hua Ding ◽  
Jing Wei Zhao
Keyword(s):  
Mechanical Properties ◽  
Retained Austenite ◽  
Room Temperature ◽  
Volume Fraction ◽  
Total Elongation ◽  
Trip Effect ◽  
Low Carbon ◽  
Quenching And Partitioning ◽  
The Stability ◽  
Critical Annealing

A refined microstructure consisting of martensite and retained austenite at room temperature has been produced in a Nb-microalloyed low carbon Si-Mn steel by a novel heat-treatment, pre-quenching prior to quenching and partitioning processes (Q&Q-P). The results showed that compared with the conventional quenching and partitioning steel the mechanical properties of steel obtained by the novel treatment have been significantly improved, with a good combination of ultimate tensile strength (1000MPa) and total elongation (above 30%). Meanwhile, the volume fraction of retained austenite has been increased. It was found that the improvement of mechanical properties was mainly attributed to the enhanced TRIP effect due to the relatively high fraction of metastable retained austenite at room temperature. The increased stability of austenite results from the C and Mn partitioning during inter-critical annealing, which increased the chemical stability of austenite. The formation of refined austenite at inter-critical annealing also had a positive effect on the stability of the austenite. As a consequence, the volume fraction of retained austenite at room temperature was significantly increased. Compared with the Q-P steel, the Q&Q-P steel exhibited higher work hardening exponents during the stage of TRIP effect and had the higher ductility.

Effect of Al on the Microstructure and Mechanical Properties of Hot-Rolled Medium-Mn Steel

2018 ◽  
Vol 941 ◽  
pp. 292-298 ◽  
Author(s):  
Ding Ting Han ◽  
Yun Bo Xu ◽  
Ying Zou ◽  
Zhi Ping Hu ◽  
Shu Qing Chen ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Trip Steel ◽  
Retained Austenite ◽  
Mechanical Stability ◽  
Volume Fraction ◽  
Microstructure And Mechanical Properties ◽  
Medium Mn Steel ◽  
Hot Rolled ◽  
Mn Steel

The present investigation was made to study the effect of Al on the microstructure and mechanical properties of hot-rolled medium-Mn TRIP steel (abbreviated as Al-TRIP). As a contrast, a Si-added medium-Mn TRIP steel (abbreviated as Si-TRIP) was also studied. Addition Al in medium-Mn steel can raise Ac3 temperature, which will restrain austenite transformation and expand the two-phase region, promoting Mn and C elements enriched in austenite. In-depth microstructure and mechanical properties analysis were carried out for the hot-rolled Al-TRIP and Si-TRIP steels in this study. The microstructure was characterized by scanning electron microscope (SEM) and electron probe microanalyzer (EPMA). Volume fraction of retained austenite was measured by D/max2400 X-ray diffractometer (XRD). A dual-phase microstructure consisting of ultra-fine grained intercritical ferrite (IF) and lath-like retained austenite (RA) with high mechanical stability was obtained after annealing at 630°C for 2h for Al-TRIP steel. As prolonging the intercritical annealing time, the stability of RA decreased primarily due to the increase of grain size. The tensile test results indicated that the Al-TRIP steel possessed a better combination of tensile strength and elongation compared to Si-TRIP steel. Excellent mechanical properties with yield strength of 790MPa, tensile strength of 1050MPa, total elongation of 35% and UTS×TEL of 39GPa·% was obtained for the Al-TRIP steel.

Effect of Tempering Temperature on Microstructure and Properties of Low Carbon High Silicon Alloy Steel Treated by Q-P-T Process

2020 ◽  
Vol 993 ◽  
pp. 592-596
Author(s):  
Jun Hu Wei ◽  
Xu Ran ◽  
Han Ying
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Ultimate Tensile Strength ◽  
Alloy Steel ◽  
Retained Austenite ◽  
Volume Fraction ◽  
Low Carbon ◽  
Tempering Temperature ◽  
Silicon Alloy ◽  
High Silicon

The mechanical properties and microstructure of low-carbon high-silicon alloy steel were examined under various tempering temperatures using the quenching, partitioning and tempering (Q–P–T) process. The performance changed with the variation in tempering temperature. The results show that the microstructure of low carbon high silicon alloy steel treated by Q-P-T process was mainly ferrite, martensite, carbide-free bainite and film-like retained austenite. This alloys exhibited good mechanical properties at tempering temperature of 300 °C. The product of strength and elongation were 33.7 GPa%. Specifically, the Ultimate tensile strength were 1508 MPa, the yield strength were 1048 MPa, and the elongation were 22.4%. At this temperature of 300 °C, the volume fraction of retained austenite reached 10.4%.

Sign in / Sign up

Export Citation Format

Share Document