Effect of Phosphorus on Microstructure, Mechanical Properties, and Formation of Retained Austenite in TRIP Steels

2012 ◽  
Vol 508 ◽  
pp. 128-132 ◽  
Author(s):  
Eui Pyo Kwon ◽  
Shun Fujieda ◽  
Kozo Shinoda ◽  
Shigeru Suzuki
Keyword(s):  
Mechanical Properties ◽  
Carbon Concentration ◽  
Trip Steel ◽  
Retained Austenite ◽  
Volume Fraction ◽  
Transformation Induced Plasticity ◽  
Trip Steels ◽  
The Stability

In this Study, Influences of P on the Microstructure, Mechanical Properties, and Retained Austenite Characteristics in Transformation Induced Plasticity (TRIP) Steels Were Investigated. Microstructure of 0.2mass%P Containing TRIP Steel Was Inhomogeneous and it Resulted in Deterioration of the Mechanical Properties. Retained Austenite Characteristics such as Volume Fraction and Carbon Concentration Were Also Affected by P. The Stability of Retained Austenite in P Containing TRIP Steel Was Different from that in P-Free TRIP Steel. Such Difference in the Stability of Retained Austenite Was Attributed to the Effect of the Carbon Concentration in Retained Austenite as Well as their Different Microstructure.

Temperature Development during Step-Wise Tensile Tests on a TRIP Steel

2010 ◽  
Vol 638-642 ◽  
pp. 3579-3584
Author(s):  
Lie Zhao ◽  
Corinna Thomser ◽  
Kirsten Schneider ◽  
Wolfgang Bleck ◽  
Jilt Sietsma
Keyword(s):  
Trip Steel ◽  
Retained Austenite ◽  
Room Temperature ◽  
Longitudinal Direction ◽  
Tensile Tests ◽  
Transformation Induced Plasticity ◽  
Trip Steels ◽  
Loading Process ◽  
Temperature Development ◽  
The Stability

Temperature development during plastic deformation affects the stability of retained austenite and thus the mechanical properties in transformation-induced plasticity (TRIP) steels. In this work, we used a thermo-camera to monitor the temperature development during a step-wise tensile test of an Al-containing multiphase TRIP steel. The tensile tests were performed by loading the specimen at six straining rates ranging from 5 to 30 s-1 to a stress of 700 MPa and then holding for 15 min, followed by further loading at 50 s-1 until fracture. It is found that temperature increases about 13 – 18 °C during the first loading process and drops back to room temperature with a time-constant of around 2 min. The increment of temperature increases with increasing straining rate. The temperature increases around 30 °C during the second loading process. The distribution of temperature over the specimen surface is found to be rather homogeneous along the longitudinal direction in most cases, except for the ending points of two loading processes. The measurement of temperature development is found to be consistent with previous numerical simulation on the temperature development under constant stress in TRIP steels.

Microstructure and Mechanical Properties of a Lamellar-Structured Low-Alloy TRIP Steel

2021 ◽  
Vol 1016 ◽  
pp. 1188-1192
Author(s):  
Jiang Ying Meng ◽  
Zhi Geng Jia ◽  
Tong Liang Wang ◽  
Kai Fang Li ◽  
Li He Qian
Keyword(s):  
Mechanical Properties ◽  
Trip Steel ◽  
Retained Austenite ◽  
Treatment Process ◽  
Intercritical Annealing ◽  
Bainitic Ferrite ◽  
Heat Treatment Process ◽  
Transformation Induced Plasticity ◽  
Trip Steels ◽  
Reverted Austenite

In this paper, we report a lamellar-structured low-alloy transformation-induced plasticity (TRIP) steel; the microstructure of the steel consists of alternate lamellae of intercritical ferrite and reverted austenite on microscale, with the latter consisting of bainitic ferrite laths and retained austenite films on nanoscale. Such a microstructure was produced by a heat treatment process similar to that for producing conventional TRIP-assisted steels, i.e. intercritical annealing followed by austempering. Nevertheless, quenched martensite rather than a mixture of ferrite and pearlite was used as the starting structure for intercritical annealing to form austenite, and the resulting austenite was then transformed to bainite by austempering treatment. This steel exhibits much enhanced strength-ductility combinations as compared with those conventional polygonal-structured low-alloy TRIP steels.

Effect of Different Coiling Temperature on Mechanical Properties in Hot Rolled TRIP Steel

2011 ◽  
Vol 239-242 ◽  
pp. 1092-1095
Author(s):  
Xu Tao Gao ◽  
Ai Min Zhao ◽  
Zheng Zhi Zhao ◽  
Ming Ming Zhang ◽  
Di Tang
Keyword(s):  
Mechanical Properties ◽  
Retained Austenite ◽  
X Ray Diffraction ◽  
Coiling Temperature ◽  
Experimental Steel ◽  
Transformation Induced Plasticity ◽  
X Ray ◽  
Trip Steels ◽  
Hot Rolled ◽  
Scanning Electron

By means of optical microscopy(OM), scanning electron microscopy(SEM),X-ray diffraction(XRD),And tensile test, Mechanical Properties of hot rolled transformation -induced plasticity (TRIP) steels which were prepared through three different coiling temperature was investigated. Result reveals that the formability index of the experimental steel descends when the coiling temperature becomes low. Different coiling temperature has greater impact on retained austenite. Amount and carbon content of retained austenite in the experimental steel get less with lower coiling temperature.

scholarly journals Quantitative Description of External Force Induced Phase Transformation in Silicon–Manganese (Si–Mn) Transformation Induced Plasticity (TRIP) Steels

Materials ◽  
2019 ◽  
Vol 12 (22) ◽  
pp. 3781
Author(s):  
Zhongping He ◽  
Huachu Liu ◽  
Zhenyu Zhu ◽  
Weisen Zheng ◽  
Yanlin He ◽  
...  
Keyword(s):  
Phase Transformation ◽  
Carbon Steel ◽  
Trip Steel ◽  
Retained Austenite ◽  
Low Carbon Steel ◽  
High Strength ◽  
High Plasticity ◽  
Low Carbon ◽  
Transformation Induced Plasticity ◽  
Trip Steels

Transformation Induced Plasticity (TRIP) steels with silicon–manganese (Si–Mn) as the main element have attracted a lot of attention and great interest from steel companies due to their low price, high strength, and high plasticity. Retained austenite is of primary importance as the source of high strength and high plasticity in Si–Mn TRIP steels. In this work, the cold rolled sheets of Si–Mn low carbon steel were treated with TRIP and Dual Phase (DP) treatment respectively. Then, the microstructure and composition of the Si–Mn low carbon steel were observed and tested. The static tensile test of TRIP steel and DP steel was carried out by a CMT5305 electronic universal testing machine. The self-built true stress–strain curve model of TRIP steel was verified. The simulation results were in good agreement with the experimental results. In addition, the phase transformation energy of retained austenite and the work borne by austenite in the sample during static stretching were calculated. The work done by austenite was 14.5 J, which was negligible compared with the total work of 217.8 J. The phase transformation energy absorption of retained austenite in the sample was 9.12 J. The role of retained austenite in TRIP steel is the absorption of excess energy at the key place where the fracture will occur, thereby increasing the elongation, so that the ferrite and bainite in the TRIP steel can absorb energy for a longer time and withstand more energy.

The Effect of Isothermal Hold Temperature on Microstructure and Mechanical Properties of TRIP Steel

2017 ◽  
Vol 270 ◽  
pp. 253-257 ◽  
Author(s):  
Ludmila Kučerová ◽  
Martin Bystrianský ◽  
Josef Káňa
Keyword(s):  
Mechanical Properties ◽  
Trip Steel ◽  
Retained Austenite ◽  
Mechanical Treatment ◽  
Volume Fraction ◽  
Carbon Steels ◽  
Processing Route ◽  
Isothermal Hold ◽  
Low Carbon ◽  
Thermo Mechanical Treatment

TRIP (transformation induced plasticity) steels are low alloyed low carbon steels with complex microstructures consisting of ferrite, bainite and retained austenite. This complex microstructure provides them with excellent strength to ductility balance, making them a member of advanced high strength steels (AHSS) group. Suitable microstructure can be obtained by either heat or thermo-mechanical treatment. A hold in bainite transformation region is an integral part of any form of commercial TRIP steel processing route, as it enables formation of sufficient volume fraction of bainite and also stabilization of retained austenite in the final microstructure. Various bainitic hold temperatures ranging from 350 °C to 500 °C were tested within thermo-mechanical treatment of 0.2C-1.5Mn-0.6S-1.5Al steel and the final microstructures were evaluated with regard to the suitability to TRIP effect and achieved mechanical properties. The microstructures were analyzed by scanning electron microscopy and mechanical properties measured by tensile test.

Study on Microstructures and Mechanical Properties of Cold-Rolled C-Mn-Si-Al TRIP Steel

2010 ◽  
Vol 146-147 ◽  
pp. 678-681
Author(s):  
Zheng You Tang ◽  
Hua Ding
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Trip Steel ◽  
Retained Austenite ◽  
Volume Fraction ◽  
Total Elongation ◽  
Partial Substitution ◽  
Cold Rolled ◽  
Microstructures And Mechanical Properties

The effect of the partial substitution of Si by Al on the microstructures and the mechanical properties of cold rolled C-Mn-Si TRIP steel was investigated. The results show that the partial substitution of Si by Al could refine the microstructures, increase the volume fraction of ferrite and retained austenite. In addition, the excellent mechanical properties of the Al partial substituted TRIP steel could be obtained, the tensile strength, total elongation and strength-ductility of C-Mn-Si-Al TRIP steel are 739MPa, 38% and 28082MPa%, respectively.

Transformation Induced Plasticity (TRIP) Effect Used in Forming of Carbon CMnSi Steel

2005 ◽  
Vol 500-501 ◽  
pp. 461-470 ◽  
Author(s):  
Jiří Kliber ◽  
Bohuslav Mašek ◽  
Ondrej Zacek ◽  
H. Staňková
Keyword(s):  
Continuous Casting ◽  
Hot Rolling ◽  
Retained Austenite ◽  
Volume Fraction ◽  
Thermomechanical Processing ◽  
High Strength ◽  
Ferrite Matrix ◽  
Transformation Induced Plasticity ◽  
Trip Steels ◽  
Forming Temperature

Transformation induced plasticity (TRIP) steel combines high strength and high ductility that makes it particularly suitable for forming. Martensite within a ferrite matrix is usually obtained either by continuous casting of slabs followed by hot rolling (which is the fastest method, hence the most economical one, producing, however, relatively thick products) or by the continuous casting of slabs followed by hot rolling, cold rolling and annealing (the method used for thin products). High cooling rates, low coiling temperatures and low reduction during hot deformation were generally found to suppress the formation of polygonal ferrite and promote the presence of retained austenite. This paper focuses on development and modifications of two CMnSi-based TRIP steels with 0,23 % C;1,4 % Mn; 1,9 % Si; ( 0,08 % Nb) by means of laboratory thermomechanical processing. Description of experimental devices for the analysis of transformation plasticity under tensioncompression loading is given. Experiments were carried out on the simulator for thermaldeformation cycles SMITWELD and TANDEM was used for thermomechanical processing on the laboratory rolling mill. The maximum volume fraction of retained austenite and the resulting optimum combination of tensile strength and ductility were achieved in testing heats. Special attention was paid to volume fraction changes of single phases and to changes in morphology of phases. The results suggest that rather short isothermal bainite transformation times are sufficient to obtain TRIP microstructure. The influence of parameters of thermomechanical processing such as the amount of strain, forming temperature and austenitization time and temperature on microstructures of TRIP steels were evaluated.

Linking Crystallographic, Chemical and Nano-Mechanical Properties of Phase Constituents in DP and TRIP Steels

2010 ◽  
Vol 638-642 ◽  
pp. 3465-3472 ◽  
Author(s):  
R. Arjan Rijkenberg ◽  
Maxim P. Aarnts ◽  
Floor A. Twisk ◽  
Marga J. Zuijderwijk ◽  
M. Knieps ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Phase Transformation ◽  
Crack Initiation ◽  
Trip Steel ◽  
Retained Austenite ◽  
Trip Steels ◽  
Nano Indentation ◽  
Ebsd Data ◽  
Indentation Analysis

This paper discusses practical EBSD strategies for identification and partitioning of phase constituents in DP and TRIP microstructures including martensite, retained-austenite, bainite, intercritical and epitaxial ferrite. EBSD data is complemented with nano-indentation analysis, providing evidence of indentation-induced phase transformation of retained-austenite in TRIP steel and micro-crack initiation at the interface between ferrite and mechanically transformed martensite.

Ultra Fine-Grained 6wt% Manganese TRIP Steel

2010 ◽  
Vol 654-656 ◽  
pp. 286-289 ◽  
Author(s):  
Sea Woong Lee ◽  
Kyoo Young Lee ◽  
Bruno C. De Cooman
Keyword(s):  
Mechanical Properties ◽  
Retained Austenite ◽  
Annealing Temperature ◽  
Volume Fraction ◽  
Intercritical Annealing ◽  
High Volume ◽  
Magnetic Saturation ◽  
Trip Steels ◽  
Fine Grained ◽  
Annealing Temperatures

Ultra-fine grained TRIP steels (UFG-TRIP) containing 6wt%Mn were produced by intercritical annealing. An ultra-fine grained microstructure with a grain size less than 1μm was obtained. The formation mechanism of the high volume fraction of retained austenite was investigated by dilatometry, XRD and magnetic saturation. The fraction of retained austenite was strongly dependent on the annealing temperature. The tensile properties were also found to be strongly influenced by the annealing temperature with poorer mechanical properties being observed at higher annealing temperatures. It was found that the stabilization of the retained austenite was both a composition and size-effect, made possible by the grain refinement due to the reversely transformed martensite.

Sign in / Sign up

Export Citation Format

Share Document