scholarly journals Special Issues/ Surface Treatments for Automobile. Surface Treatment Engineering for Car Interior Parts.

1992 ◽  
Vol 43 (6) ◽  
pp. 539-542
Author(s):  
Kazuo MARUYA
Keyword(s):  
Surface Treatment ◽  
Surface Treatments

scholarly journals Effect of surface treatments on push-out bond strength of calcium silicate-based cements to fiber posts

2021 ◽  
Vol 21 (1) ◽  
Author(s):  
Amr M. Elnaghy ◽  
Ayman Mandorah ◽  
Ali H. Hassan ◽  
Alaa Elshazli ◽  
Shaymaa Elsaka
Keyword(s):  
Bond Strength ◽  
Surface Treatment ◽  
Glass Fiber ◽  
Calcium Silicate ◽  
Surface Treatments ◽  
The Other ◽  
Fiber Posts ◽  
Glass Fiber Posts ◽  
Push Out ◽  
Effect Of Surface

Abstract Background To evaluate the effect of surface treatments on the push-out bond strength of Biodentine (BD) and white mineral trioxide aggregate (WMTA) to fiber posts. Methods Two brands of fiber posts were used: Reblida post; RP and RelyX post; RX. Each type of post (n = 80/group) was divided into four groups (n = 20/group) and exposed to surface treatment as follows: Control (no treatment), sandblasting (SB), hydrofluoric acid (HF), and TiF4 4 wt/v%. Each group was further subdivided into two subgroups (n = 10/subgroup) based on the type of CSCs used as follows: Subgroup A: BD and Subgroup B: WMTA. Push-out bond strength of BD and WMTA to glass fiber posts was assessed. Data were statistically analyzed using three-way ANOVA and Tukey’s test. A Weibull analysis was performed on the push-out bond strength data. Results BD showed higher bond strength than WMTA (P < 0.001). The push-out bond strength for posts treated with TiF4 4 wt/v% showed greater bond strength than the other surface treatments (P < 0.05). The BD/RP-TiF4 4 wt/v% showed the greater characteristic bond strength (σ0) (15.93) compared with the other groups. Surface treatments modified the surface topography of glass fiber posts. Conclusions The BD/RP-TiF4 4 wt/v% showed greater bond strength compared with the other groups. The TiF4 4 wt/v% surface treatment enhanced the bond strength of BD and WMTA to glass fiber posts than the other treatments. Surface treatment of fiber post with TiF4 4 wt/v% could be used to improve the bond strength with calcium silicate-based cements.

scholarly journals Surface activation of High Impact Polystyrene substrate using dynamic atmospheric pressure plasma

2019 ◽  
Vol 4 (1) ◽  
pp. 80-87
Author(s):  
Gergely Juhász ◽  
Miklós Berczeli ◽  
Zoltán Weltsch
Keyword(s):  
Surface Treatment ◽  
Atmospheric Pressure ◽  
Adhesive Bonding ◽  
Atmospheric Pressure Plasma ◽  
Theoretical Background ◽  
Surface Treatments ◽  
Surface Adhesion ◽  
Adhesion Properties ◽  
Pressure Plasma ◽  
Plasma Surface Treatment

Over the last decade, the number of researches has increased in the field of bonding technologies. Researchers attempt to improve surface adhesion properties by surface treatments. Adhesive bonding is one of these bonding techniques, where it is important to see what surfaces will be bonded. One such surface property is wetting, which can be improved by several types of surface treatment. In recent years, atmospheric pressure plasmas have appeared, with which research is ongoing on surface treatments. In our research, we will deal with the effects of plasma surface treatment at atmospheric pressure and its measurement. In addition, we summarize the theoretical background of adhesion, surface tension and surface treatment with atmospheric pressure plasma. Our goal is to improve adhesion properties and thus the adhesion quality.

scholarly journals Effect of surface treatments on repair strength, roughness and morphology in aged metal-free crowns

2020 ◽  
Vol 19 ◽  
pp. e206155
Author(s):  
Yançanã Luizy Gruber ◽  
Thaís Emanuelle Bakaus ◽  
Bruna Fortes Bittencourt ◽  
João Carlos Gomes ◽  
Alessandra Reis ◽  
...  
Keyword(s):  
Bond Strength ◽  
Surface Treatment ◽  
Adhesive System ◽  
Surface Treatments ◽  
Metal Free ◽  
Diamond Bur ◽  
Before And After ◽  
Post Test ◽  
Microshear Bond Strength

Aim: The roughness and micromorphology of various surface treatments in aged metal-free crowns and the bond strength of these crowns repaired with composite resin (CR) was evaluated in vitro. Methods: A CR core build-up was confectioned in 60 premolars and prepared for metal-free crowns. Prepared teeth were molded with the addition of silicone, and the laboratory ceromer/fiber-reinforced crowns (SR Adoro/Fibrex Lab) were fabricated. Subsequently, the crowns were cemented and artificially aged in a mechanical fatigue device (1.2 X 106 cycles), then divided into 4 groups (n = 15) according to the surface treatment: 1) phosphoric acid etching (PA); 2) PA + silane application; 3) roughening with a diamond bur + PA; and 4) sandblasting with Al2O3 + PA. After the treatments, the crowns (n = 2) were qualitatively analyzed by scanning electron microscope (SEM) and surface roughness (n = 5) was analyzed before and after the surface treatment (Ra parameter). The remaining crowns (n = 8) received standard repair with an adhesive system (Tetric N-Bond) and a nanohybrid CR (Tetric N-Ceram), and the microshear bond strength (SBS) test was performed (0.5 mm/min). Roughness and SBS data were analyzed by one- and two-way ANOVA, respectively, as well as Tukey’s post-test (α = 0.05). Results: Sandblasting with Al2O3 + PA resulted in the highest final roughness and SBS values. The lowest results were observed in the PA group, whereas the silane and diamond bur groups showed intermediate values. Conclusion: It may be concluded that indirect ceromer crowns sandblasted with aluminum oxide prior to PA etching promote increased roughness surface and bond strength values.

scholarly journals Assessment the Bond Strength of Ceramic Brackets to CAD/CAM Nanoceramic Composite and Interpenetrating Network Composite after Different Surface Treatments

2018 ◽  
Vol 2018 ◽  
pp. 1-6 ◽  
Author(s):  
Mustafa Mehmet Özarslan ◽  
Özlem Üstün ◽  
Ulviye Sebnem Buyukkaplan ◽  
Çağatay Barutcigil ◽  
Nurullah Türker ◽  
...  
Keyword(s):  
Bond Strength ◽  
Surface Treatment ◽  
Hydrofluoric Acid ◽  
Shear Bond Strength ◽  
Surface Treatments ◽  
Interpenetrating Network ◽  
Bonding Performance ◽  
Cad Cam ◽  
Ceramic Brackets ◽  
New Generation

Adult orthodontics may confront problems related to the bonding performance of orthodontic brackets to new generation restorative materials used for crown or laminate restorations. The aim of the present study was to investigate the shear bond strength of ceramic brackets to two new generation CAD/CAM interpenetrating network composite and nanoceramic composite after different surface treatments. Er,Cr:YSGG Laser, hydrofluoric acid (9%), sandblasting (50 μm Al2O3), and silane were applied to the surfaces of 120 CAD/CAM specimens with 2 mm thickness and then ceramic brackets were bonded to the treated surfaces of the specimens. Bond strength was evaluated using the shear bond strength test. According to the results, CAD/CAM block types and surface treatment methods have significant effects on shear bond strength. The lowest bond strength values were found in the specimens treated with silane (3.35 ± 2.09 MPa) and highest values were found in the specimens treated with sandblast (8.92 ± 2.77 MPa). Sandblasting and hydrofluoric acid surface treatment led to the most durable bonds for the two types of CAD/CAM blocks in the present study. In conclusion, different surface treatments affect the shear bond strength of ceramic brackets to CAD/CAM interpenetrating network composite and nanoceramic composite. Among the evaluated treatments, sandblasting and hydrofluoric acid application resulted in sufficient bonding strength to ceramic brackets for both of the CAD/CAM materials.

Calibration of Performance Models for Surface Treatment to Chilean Conditions: The HDM-4 Case

2003 ◽  
Vol 1819 (1) ◽  
pp. 285-293 ◽  
Author(s):  
Solminihac T. Hernán de ◽  
Hidalgo S. Priscila ◽  
Salgado T. Mauricio
Keyword(s):  
Surface Treatment ◽  
Climatic Conditions ◽  
Surface Treatments ◽  
Pavement Management ◽  
Management Model ◽  
Performance Curve ◽  
Performance Models ◽  
Development Management ◽  
Equivalent Models ◽  
Structural Capacity

The HDM-4 (Highway Development Management) model used for pavement management activities must be adjusted to the specific conditions of a country or region where they are to be used by adjusting certain calibration factors. The results obtained from calibrating the cracking, raveling, potholing, rut depth, and roughness models contemplated in HDM-4 version 1.1 for surface treatments are presented and compared with the results obtained from equivalent models of HDM-III. In this task, the “windows” methodology was used, which consists of reconstructing the distress performance curve of a specific road category starting with observation of the condition of different roads with similar characteristics (such as traffic, pavement structural capacity, and climatic conditions) but of different ages. On the basis of the results obtained, recommendations for calibrating the performance models are proposed, and calibration factors more adequate for characteristics specific to Chilean surface treatments are established. On comparing the results of the calibrated models of HDM-III and HDM-4, it is concluded that both cases furnish similar values, and use of HDM-4 models is recommended because of their operating advantages and because they afford a greater flexibility, which allows them to more aptly adapt to a broader number of cases and situations.

scholarly journals Influence of Surface Treatment on Strength Distribution of Vita VMK 68 Dental Porcelains

2013 ◽  
Vol 2013 ◽  
pp. 1-7
Author(s):  
Serkan Nohut ◽  
Ahmet Tasdemir ◽  
Suleyman Aykut Korkmaz
Keyword(s):  
Distribution Function ◽  
Weibull Distribution ◽  
Statistical Model ◽  
Surface Treatment ◽  
Goodness Of Fit ◽  
Strength Distribution ◽  
Surface Treatments ◽  
Bending Test ◽  
Dental Ceramics ◽  
Weibull Distribution Function

Weibull distribution function is the most commonly used statistical model for the investigation of mechanical properties of dental ceramics and design process with dental ceramics. However, it is still unclear whether the Weibull distribution function is the most appropriate function for fitting the strength data of dental ceramics with different surface treatments. In this paper, three-point bending test results of feldspathic body porcelain (Vita VMK 68) specimens with four different surface treatments are analysed. According to goodness-of-fit tests (Anderson-Darling test, Kolmogorov-Smirnov test, and Akaike information criterion), it is shown that the type of surface treatment has an important influence on deviation of strength distribution from perfect Weibull statistics. It is concluded that estimation of the most suitable statistical model for Vita VMK 68 is not only a material-dependent but also a process-dependent (machining of the specimens) procedure.

Increased Filiform Corrosion Resistance Utilizing a Zirconium-Based Conversion Coating on an Al-Zn-Mg-Cu (AA7075-T6) Alloy as well as Selected Surface Treatments

CORROSION ◽  
10.5006/3510 ◽  
2020 ◽  
Author(s):  
Carol Glover ◽  
Mary Lyn Lim ◽  
John Scully
Keyword(s):  
Surface Treatment ◽  
Photoelectron Spectroscopy ◽  
Conversion Coating ◽  
Surface Treatments ◽  
Treatment Processes ◽  
Filiform Corrosion ◽  
Alkaline Cleaning ◽  
Vinyl Butyral ◽  
Subsequent Acid ◽  
Effect Of Surface

This study investigates the effect of surface treatment on the formation of Zr-based conversion coatings on AA7075-T6 automotive aluminum alloys and their resistance to filiform corrosion (FFC). Two different surface treatments were studied (A) alkaline-cleaning and (B) alkaline-cleaning with a subsequent acid deoxidation step. A model poly-vinyl butyral (PVB) primer coating was used as the topcoat and specimens were studied with and without the application of a Zr-based conversion coating. Comparisons were made against a control that had no surface treatment. The FFC filament initiation time and propagation kinetics were of particular interest. Scanning electron microscopy (SEM) and x-ray photoelectron spectroscopy (XPS) were used to examine the conversion coating thickness and composition. A bi-layer conversion coating structure is demonstrated and both surface treatments are shown to produce copper enrichment that promotes the formation of the Zr-rich coating. Specimens prepared by alkaline cleaning-only resulted in a substantially thicker oxide layer of which 97% was ZrO2. These specimens provide superior resistance to FFC where the thick Zr-rich oxide is thought to provide a dense blocking layer that prevents electron transfer at the interface. In contrast, the control specimen, exposed only to the copper additions present in the conversion bath is shown to produce an Al oxide-rich layer with only a 33% ZrO2 contribution in the outer layer. The findings demonstrate that the redistribution of functional copper species, that is shown to occur during surface treatment processes, is crucial for the formation of a robust Zr film.

scholarly journals Effect of surface treatment of prefabricated teeth on shear bond strength of orthodontic brackets

2017 ◽  
Vol 22 (4) ◽  
pp. 47-52 ◽  
Author(s):  
Marina Cumerlato ◽  
Eduardo Martinelli de Lima ◽  
Leandro Berni Osorio ◽  
Eduardo Gonçalves Mota ◽  
Luciane Macedo de Menezes ◽  
...  
Keyword(s):  
Bond Strength ◽  
Surface Treatment ◽  
Shear Bond Strength ◽  
Testing Machine ◽  
Surface Treatments ◽  
Orthodontic Brackets ◽  
Positive Correlation ◽  
Diamond Bur ◽  
Group 2 ◽  
Group 1

ABSTRACT Objective: The aim of this in vitro study was to evaluate and compare the effects of grinding, drilling, sandblasting, and ageing prefabricated teeth (PfT) on the shear bond strength (SBS) of orthodontic brackets, as well as the effects of surface treatments on the adhesive remnant index (ARI). Methods: One-hundred-ninety-two PfT were divided into four groups (n = 48): Group 1, no surface treatment was done; Group 2, grinding was performed with a cylindrical diamond bur; Group 3, two drillings were done with a spherical diamond bur; Group 4, sandblasting was performed with 50-µm aluminum oxide. Before the experiment, half of the samples stayed immersed in distilled water at 37oC for 90 days. Brackets were bonded with Transbond XT and shear strength tests were carried out using a universal testing machine. SBS were compared by surface treatment and by ageing with two-way ANOVA, followed by Tukey’s test. ARI scores were compared between surface treatments with Kruskal-Wallis test followed by Dunn’s test. Results: Surface treatments on PfT enhanced SBS of brackets (p< 0.01), result not observed with ageing (p= 0.45). Groups II, III, and IV showed higher SBS and greater ARI than the Group 1 (p< 0.05). SBS was greater in the groups 3 and 4 (drilling, sandblasting) than in the Group 2 (grinding) (p< 0.05). SBS and ARI showed a positive correlation (Spearman’s R2= 0.57; p< 0.05). Conclusion: Surface treatment on PfT enhanced SBS of brackets, however ageing did not show any relevance. Sandblasting and drilling showed greater SBS than grinding. There was a positive correlation between SBS and ARI.

Application of Polypropylene Fibre with Various Surface Treatments in Concrete

2014 ◽  
Vol 1054 ◽  
pp. 75-79 ◽  
Author(s):  
Lenka Bodnárová ◽  
Petra Macháňová ◽  
Daniel Kopkáně ◽  
Petr Herka ◽  
Pavel Stahel
Keyword(s):  
Low Temperature ◽  
Surface Treatment ◽  
Polypropylene Fibre ◽  
Surface Treatments ◽  
Low Temperature Plasma ◽  
Polypropylene Fibres ◽  
Temperature Plasma ◽  
Experimental Works ◽  
Property Verification

The paper presents results of experimental works focused on property verification of concretes with an admixture of polypropylene fibres with various surface treatments. Common production polypropylene fibres with surface lubrication, polypropylene fibres without surface treatment and low temperature plasma treated polypropylene fibres were used for the testing.

Sign in / Sign up

Export Citation Format

Share Document