Test Bench for Static Transmission Error Evaluation in Gears

2020 ◽  
Author(s):  
Carlo Rosso ◽  
Tommaso Maggi ◽  
Claudio Marcellini ◽  
Fabio Bruzzone
Keyword(s):  
Test Bench ◽  
Transmission Error ◽  
Error Evaluation ◽  
Static Transmission Error

Measurement of Transmission Nonlinearities in Servodrives

2014 ◽  
Vol 613 ◽  
pp. 248-252
Author(s):  
Michal Pajkoš ◽  
Viktor Šlapák ◽  
Radovan Sivý ◽  
František Ďurovský
Keyword(s):  
Machine Tools ◽  
Test Bench ◽  
Transmission Error ◽  
Experimental Measurements ◽  
Error Evaluation ◽  
Dynamic Measurements ◽  
Position Accuracy ◽  
Nc Machine ◽  
Nc Machine Tools

Paper presents transmission nonlinearities of servodrives. These nonlinearities directly affect the performance and precision of industrial machines such as robots, manipulators, NC machine tools etc. For measuring purpose of these nonlinearities a measurement test bench was created. Presented measuring test bench is used for static and dynamic measurements of servodrives as well as for precision and gear error evaluation. Paper focuses on properties, analysis and experimental measurements of angular transmission error, torsional elasticity and repeated position accuracy.

Effects of the Gear Tooth Modification on the Nonlinear Dynamics of Gear Transmission System

2010 ◽  
Vol 97-101 ◽  
pp. 2764-2769
Author(s):  
Si Yu Chen ◽  
Jin Yuan Tang ◽  
C.W. Luo
Keyword(s):  
Nonlinear Dynamics ◽  
Gear Tooth ◽  
Simulation Method ◽  
Transmission Error ◽  
Dynamic Responses ◽  
Meshing Stiffness ◽  
Gear Transmission System ◽  
Tooth Modification ◽  
Static Transmission Error ◽  
Misalignment Error

The effects of tooth modification on the nonlinear dynamic behaviors are studied in this paper. Firstly, the static transmission error under load combined with misalignment error and modification are deduced. These effects can be introduced directly in the meshing stiffness and static transmission error models. Then the effect of two different type of tooth modification combined with misalignment error on the dynamic responses are investigated by using numerical simulation method. The numerical results show that the misalignment error has a significant effect on the static transmission error. The tooth crowning modification is generally preferred for absorbing the misalignment error by comparing with the tip and root relief. The tip and root relief can not resolve the vibration problem induced by misalignment error but the crowning modification can reduce the vibration significantly.

Dynamic Analysis of a Multi-Mesh Helical Gear Train

1992 ◽  
Author(s):  
Ahmet Kahraman
Keyword(s):  
Loading Condition ◽  
Helix Angle ◽  
Transmission Error ◽  
Helical Gear ◽  
Forced Response ◽  
Gear Train ◽  
Loading Conditions ◽  
Gear Mesh ◽  
Natural Modes ◽  
Static Transmission Error

Abstract In this paper, the dynamic behavior of a multi-mesh helical gear train is studied. The gear train consists of three helical gears, with one of the gears in mesh with the other two. An 18-degree-of-freedom dynamic model which includes transverse, torsional, axial and rotational (rocking) motions of the flexibly mounted gears is developed. Two different loading conditions are identified. For case I, the system is driven by the gear in the middle, and for case II, the system is driven by one of the gears at either end of the gear train. Gear mesh phases under each loading condition are determined. The natural modes are predicted, and effects of the helix angle and the loading condition on the natural modes are explained. The forced response, which includes dynamic mesh and bearing forces, due to the static transmission error excitation is found. Effects of loading conditions and asymmetric positioning on the response are also explored. The results suggest that the dynamic forces are lower if the number of teeth of the gear in the middle is (i) an odd number for case I type loading, and (ii) an even number for case II type loading.

An Analytical and Numerical Investigation of Modulation Sidebands of a Planetary Gear Under Fluctuated External Torque

2018 ◽  
Author(s):  
Yunbo Yuan ◽  
Wei Liu ◽  
Yahui Chen ◽  
Donghua Wang
Keyword(s):  
Planetary Gear ◽  
Transmission Error ◽  
Operating Conditions ◽  
Radial Acceleration ◽  
External Torque ◽  
Gear Mesh ◽  
Planetary Gear Sets ◽  
Static Transmission Error ◽  
Frequency Modulations ◽  
Mesh Phasing

Certain operating conditions such as fluctuation of the external torque to planetary gear sets can cause additional sidebands. In this paper, a mathematical model is proposed to investigate the modulation mechanisms due to a fluctuated external torque (FET), and the combined influence of such an external torque and manufacturing errors (ME) on modulation sidebands. Gear mesh interface excitations, namely gear static transmission error excitations and time-varying gear mesh stiffness, are defined in Fourier series forms. Amplitude and frequency modulations are demonstrated separately. The predicted dynamic gear mesh force spectra and radial acceleration spectra at a fixed position on ring gear are both shown to exhibit well-defined modulation sidebands. Comparing with sidebands caused by ME, more complex sidebands appear when taking both FET and ME into account. An obvious intermodulation is found around the fundamental gear mesh frequency between the FET and ME in the form of frequency modulations, however, no intermodulation in the form of amplitude modulations. Additionally, the results indicate that some of the sidebands are cancelled out in radial acceleration spectra mainly due to the effect of planet mesh phasing, especially when only amplitude modulations are present.

Low excitation spur gears with variable tip diameter

2021 ◽  
Vol 263 (5) ◽  
pp. 1275-1285
Author(s):  
Joshua Götz ◽  
Sebastian Sepp ◽  
Michael Otto ◽  
Karsten Stahl
Keyword(s):  
Transmission Error ◽  
Spur Gear ◽  
Low Noise ◽  
Spur Gears ◽  
Mesh Stiffness ◽  
Helical Gears ◽  
Axial Forces ◽  
Tooth Width ◽  
Drive Trains ◽  
Static Transmission Error

One important source of noise in drive trains are transmissions. In numerous applications, it is necessary to use helical instead of spur gear stages due to increased noise requirements. Besides a superior excitation behaviour, helical gears also show additional disadvantageous effects (e.g. axial forces and tilting moments), which have to be taken into account in the design process. Thus, a low noise spur gear stage could simplify design and meet the requirements of modern mechanical drive trains. The authors explore the possibility of combining the low noise properties of helical gears with the advantageous mechanical properties of spur gears by using spur gears with variable tip diameter along the tooth width. This allows the adjustment of the total length of active lines of action at the beginning and end of contact and acts as a mesh stiffness modification. For this reason, several spur gear designs are experimentally investigated and compared with regard to their excitation behaviour. The experiments are performed on a back-to-back test rig and include quasi-static transmission error measurements under load as well as dynamic torsional vibration measurements. The results show a significant improvement of the excitation behaviour for spur gears with variable tip diameter.

scholarly journals Geometry Modification of Helical Gear for Reduction of Static Transmission Error

2018 ◽  
Vol 167 ◽  
pp. 02013
Author(s):  
Jeonghyun Park ◽  
Changjun Seo ◽  
Kwangsuck Boo ◽  
Heungseob Kim
Keyword(s):  
Transmission Error ◽  
Helical Gear ◽  
Necessary Condition ◽  
Mesh Stiffness ◽  
Profile Modification ◽  
Gear Mesh ◽  
Static Transmission Error ◽  
Excitation Mechanisms ◽  
Gear Systems ◽  
Gear Mesh Stiffness

Gear systems are extensively employed in mechanical systems since they allow the transfer of power with a variety of gear ratios. So gears cause the inherent deflections and deformations due to the high pressure which occurs between the meshing teeth when transmit power and results in the transmission error. It is usually assumed that the transmission error and variation of the gear mesh stiffness are the dominant excitation mechanisms. Predicting the static transmission error is a necessary condition to reduce noise radiated from the gear systems. This paper aims to investigate the effect of tooth profile modifications on the transmission error of helical gear. The contact stress analysis was implemented for different roll positions to find out the most critical roll angle in view point of root flank stress. The PPTE (peak-to-peak of transmission error) is estimated at the roll angles by different loading conditions with two dimensional FEM. The optimal profile modification from the root to the tip is proposed.

Development of an Analytical Model for the Static and Dynamic Transmission Error Calculation: Validation on a Single Vehicle Gear Vibration Test Bench

2000 ◽  
Author(s):  
Fabrizio Cricenti ◽  
Claus-Hermann Lang ◽  
Domenico Paradiso
Keyword(s):  
Load Distribution ◽  
Analytical Approach ◽  
Test Bench ◽  
Transmission Error ◽  
Noise Levels ◽  
High Quality ◽  
Dynamic Transmission Error ◽  
Single Vehicle ◽  
Quality And Reliability ◽  
Very High

Abstract Automotive companies are being challenged when they seek to guarantee very high quality and reliability levels for their products. Customers may complain about comfort and various other concerns such as noise generated by a certain component. Analytical, numerical simulation and testing are used to understand how certain modifications to the product can affect the excited noise level. This paper presents an analytical approach used in order to predict noise levels coming from an engaged vehicle gear pair. This is done by evaluating the static and dynamic transmission error with load distribution on the teeth engaged for the different values of micro-geometric teeth modifications. Comparing the analytical and experimental results shows that both factors can be extremely linked with noise generated by two mating gears.

Numerical and experimental investigation of a spur gear pair with unloaded static transmission error

2020 ◽  
Vol ahead-of-print (ahead-of-print) ◽  
Author(s):  
Duncai Lei ◽  
Xiannian Kong ◽  
Siyu Chen ◽  
Jinyuan Tang ◽  
Zehua Hu
Keyword(s):  
Transmission Error ◽  
Spur Gear ◽  
Gear Transmission ◽  
Dynamic Responses ◽  
Gear Pair ◽  
Mesh Stiffness ◽  
Content Type ◽  
High Order Harmonic ◽  
Static Transmission Error ◽  
Harmonic Components

Purpose The purpose of this paper is to investigate the dynamic responses of a spur gear pair with unloaded static transmission error (STE) excitation numerically and experimentally and the influences of the system factors including mesh stiffness, error excitation and torque on the dynamic transmission error (DTE). Design/methodology/approach A simple lumped parameters dynamic model of a gear pair considering time-varying mesh stiffness, backlash and unloaded STE excitation is developed. The STE is calculated from the measured tooth profile deviation under the unloaded condition. A four-square gear test rig is designed to measure and analyze the DTE and vibration responses of the gear pair. The dynamic responses of the gear transmission are studied numerically and experimentally. Findings The predicted numerical DTE matches well with the experimental results. When the real unloaded STE excitation without any approximation is used, the dynamic response is dominated by the mesh frequency and its high order harmonic components, which may not be result caused by the assembling error. The sub-harmonic and super-harmonic resonant behaviors are excited because of the high order harmonic components of STE. It will not certainly prevent the separations of mesh teeth when the gear pair is under the condition of high speed and heavy load. Originality/value This study helps to improve the modeling method of the dynamic analysis of spur gear transmission and provide some reference for the understanding of the influence of mesh stiffness, STE excitation and system torque on the vibration behaviors.

Sign in / Sign up

Export Citation Format

Share Document