Mixing Characteristics and Enhancement of Sonic Elliptic Jets from a Twin Elliptic Orifice

2020 ◽  
Vol 12 (2) ◽  
Author(s):  
S. Parameshwari ◽  
Pradeep Kumar ◽  
S. Thanigaiarasu ◽  
E. Rathakrishnan
Keyword(s):  
Boundary Layer ◽  
Aspect Ratio ◽  
System Design ◽  
Pressure Ratio ◽  
Jet Noise ◽  
Nozzle Pressure Ratio ◽  
Jet Mixing ◽  
Nozzle Pressure ◽  
Mixing Characteristics ◽  
Ir Signature

The knowledge of jet mixing and its enhancement of elliptic jet are important in a propulsion system of aircraft, rocket, and missile’s system design for advancement of combustion via fuel-air mixture increment, lowering the jet noise and reduction of the plume infrared (IR) signature. The jet issuing from a twin elliptic orifice is non-uniform in shape that promotes the faster mixing and it influences by orifice exit conditions, so knowledge of absence of boundary layer and jet mixing characteristics is important. Hence, an experimental work helps to study the jet mixing for a twin elliptic orifice of aspect ratio two at nozzle pressure ratios of one, two, and three. The proximity between the orifices kept as one to 3mm in steps of one. The experimental readings were taken using pitot probe. The results revealed that jet mixing is faster and effective when the proximity between the orifices is closer to each other than the faraway distances at measured nozzle pressure ratios. Difference in orifice jet core exerted a noticeable influence at high proximity levels of nozzle pressure ratio of three and four for elliptic orifice.

Tab Aspect Ratio Effect on Supersonic Jet Mixing

2015 ◽  
Vol 32 (3) ◽  
Author(s):  
Mrinal Kaushik ◽  
E. Rathakrishnan
Keyword(s):  
Aspect Ratio ◽  
Pressure Ratio ◽  
Supersonic Jet ◽  
Small Scale ◽  
Jet Mixing ◽  
Core Length ◽  
Nozzle Pressure ◽  
The Waves ◽  
Length Reduction ◽  
Better Than

AbstractThe efficacy of introducing mixing promoting small-scale vortices by two rectangular tabs, of aspect ratio 1.0, 1.5 and 2.0, placed at diametrically opposite locations at the exit of a Mach 1.73 convergent–divergent circular nozzle has been experimentally investigated, for NPRs from 4 to 8, covering overexpanded, correctly expanded and underexpanded states of the jet. The area blockage due to the each tab was 2.5% of the nozzle exit area. Keeping the blockage constant, the aspect ratio (defined as the ratio of length to width of the tab) was varied. A maximum core length reduction of 84.6% was caused by the tabs of aspect ratio 1.0, at underexpanded conditions corresponding to NPR (nozzle pressure ratio) 6. At this NPR, tabs of aspect ratio 1.5 and 2.0 caused core length reduction of 76.9% and 61.5%, respectively. The mixing promoting efficiency of aspect ratio 1.0 is found to be better than 1.5 and 2.0, at all NPRs of the present study, except NPR 5. The shadowgraph pictures of the uncontrolled and controlled jets clearly demonstrate the effectiveness of the tabs in weakening the waves in the jet core.

Control of Subsonic and Sonic Jets with Limiting Tabs

2017 ◽  
Vol 34 (1) ◽  
Author(s):  
T. Berrueta ◽  
E. Rathakrishnan
Keyword(s):  
Nozzle Exit ◽  
Pressure Ratio ◽  
Nozzle Pressure Ratio ◽  
Jet Mixing ◽  
Downstream Distance ◽  
The Core ◽  
Maximum Reduction ◽  
Sonic Jet ◽  
Nozzle Pressure ◽  
Mach Numbers

AbstractAerodynamic mixing of subsonic and sonic jets with limiting tabs, with and without corrugations, has been studied experimentally. Limiting tab located at the nozzle exit and at a downstream distance of 0.5D has been considered in this study. Mixing caused by the tab at nozzle exit is found to be better that of tab at 0.5D, for both plain and corrugated geometries. Also, both tabs caused better mixing for underexpanded sonic jets than the correctly expanded sonic jet and subsonic jets. At nozzle pressure ratio 3 the plain tab at the nozzle exit reduced the core by about 56 % and the corrugated tab by about 51 %. But when the plain tab is placed at 0.5D the jet mixing is retarded. However, the corrugated tab at 0.5D enhances the mixing, though not up to the level of the same tab at 0D, at all Mach numbers except 0.6. The maximum reduction of core caused by shifted corrugated tab is 14 % for Mach 0.8 jet.

scholarly journals Experimental Assessment of Corrugated Rectangular Actuators on Supersonic Jet Mixing

Actuators ◽  
2020 ◽  
Vol 9 (3) ◽  
pp. 88
Author(s):  
Thillaikumar T. ◽  
Tamal Jana ◽  
Mrinal Kaushik
Keyword(s):  
Pressure Ratio ◽  
Supersonic Jet ◽  
Vortex Generators ◽  
Military Aircraft ◽  
Nozzle Pressure Ratio ◽  
Engine Exhaust ◽  
Jet Mixing ◽  
Noise Characteristics ◽  
Nozzle Pressure ◽  
The Waves

To improve the stealth capability of a military aircraft, the reduction in core length is essential to reduce the heat signature and the noise characteristics of the engine exhaust. The efficacy of rectangular vortex generators in achieving these objectives has been demonstrated by several researchers, owing to their simplicity. One way of producing the mixed-size vortices is by providing corrugations on the edge of the tab (actuator). Therefore, in the current study, two tabs of aspect ratio 1.5, mounted diametrically opposite to each other at the outlet of a Mach 1.73 circular nozzle, are examined at varying levels of expansions, ranging from overexpanded to underexpanded jet states. In addition, to generate the mixed-size vortices, three corrugation geometries, i.e., rectangular, triangular, and semicircular, are configured along the tab edges. Both quantitative and qualitative investigations are carried out by using the pitot probe to measure the stagnation pressures and by utilizing a shadowgraph technique to visualize the flow field. The corrugated tabs generated a significant mixing, and among them, the tabs with triangular corrugations are found to be most effective. A maximum reduction of about 99.7% in the supersonic core is obtained with triangular corrugated tabs at near-correct-expansion, corresponding to nozzle pressure ratio (NPR) 5. Interestingly, the semicircular corrugated tab significantly reduces the asymmetry near the nozzle exit plane. The shadowgraph images confirm the efficacy of different corrugated tabs in reducing the strength of the waves, prevalent in the supersonic core.

Flow Mixing and Screech Characteristics of Elliptical Supersonic Jet

2018 ◽  
Vol 0 (0) ◽  
Author(s):  
S. Manigandan ◽  
K. Vijayaraja
Keyword(s):  
Pressure Ratio ◽  
Expansion Ratio ◽  
Shock Cell ◽  
Nozzle Pressure Ratio ◽  
Potential Core ◽  
Appreciable Change ◽  
Jet Mixing ◽  
Screech Tone ◽  
Core Length ◽  
Nozzle Pressure

Abstract The acoustic and flow characteristics of a jet with elliptical throat is studied at different levels of nozzle expansion ratio. In this study, we have taken two types of CD nozzle configuration (circular and elliptical throat) and it is studied for various NPR ratios of 2, 3, 4 and 6. In addition, the acoustic characteristic of the jet flow is also measured for respective NPRs. Measurements of acoustic data are done using microphones placed at 30, 60 and 90 degrees to imprison the effects of screech tone. At NPR 2, 3 and 4, the jet with elliptical throat witnesses superior mixing and shorter core length compared to the circular throat. Its surprising to see both the configurations provides the identical oscillation at NPR 2, 3 and 4, however the efficiency of jet mixing is larger in elliptical throat jet. As the nozzle pressure ratio increased from 2 to 3 and 3 to 4, the potential core length of the jet reduces marginally about 5 to 10 % for every NPR until nozzle pressure ratio of 5. At NPR 2 and 3, the centerline pitot pressure profile shows, the decay of jet from the elliptical throat is healthier than a circular jet. At various levels of nozzle expansion, shock cell shows an appreciable change with an increase in NPR. Introduction of the elliptical throat on circular modifies the structure of shock cell which significantly changes the magnitude of screech tone due to the weakening of shock waves.

The Role of Castellations on Pipe Jet Noise

2018 ◽  
Author(s):  
R. Anureka ◽  
K. Srinivasan
Keyword(s):  
Sound Pressure ◽  
Pressure Ratio ◽  
Jet Noise ◽  
Pressure Level ◽  
Azimuthal Direction ◽  
Acoustic Measurements ◽  
Nozzle Pressure Ratio ◽  
Nozzle Pressure ◽  
Ratio Range

This paper explores jet noise control using castellations at the exit of pipe-jets. Far-field acoustic measurements and schlieren visualizations are performed for two configurations of castellations; namely, two and four counts. The results are compared with that of pipe-jet without castellations. The nozzle pressure ratio range of the study is 1.5 to 4.5. With each configuration, the position and strength of vortices vary causing it to interact in different manners. For pipe with two castellations, the screech is amplified and the overall sound pressure level is higher than the reference jet in most of the nozzle pressure ratios under study. For pipe with four castellations, there is no noise variation in the azimuthal direction, and screech is eliminated at all nozzle pressure ratios.

High order harmonics anomaly of jet screech

2018 ◽  
Vol 32 (15) ◽  
pp. 1850154
Author(s):  
Zhe Chen ◽  
Jiu Hui Wu ◽  
A-Dan Ren ◽  
Xin Chen
Keyword(s):  
Fundamental Frequency ◽  
Sound Pressure ◽  
Pressure Ratio ◽  
Jet Noise ◽  
Pressure Level ◽  
High Order ◽  
Small Scale ◽  
Shock Cell ◽  
Nozzle Pressure Ratio ◽  
Nozzle Pressure

Imperfectly expanded supersonic jets under strong screech could generate both fundamental screech tones and multiple tones at the harmonics of the fundamental frequency. The paper compares the fundamental frequency of jets from both AR = 3 (Aspect Ratio) and AR = 4 rectangular nozzles, and conducts analysis of harmonics on Sound Pressure Level (SPL) spectrums of jet noise. The research suggests that the fundamental frequency of the first two- or three-order harmonics increases when the Nozzle Pressure Ratio (NPR) decreases, whereas the highest order harmonic decreases when the NPR decreases. Besides, the paper also observes the differences between the highest order harmonics and other harmonics that have never been reported before. Further analysis on flow field schlieren of AR = 3 nozzle indicates that the highest order harmonic is the outcome of interaction between second shock-cell and nonlinear instable wave. The revolution of these high order harmonics can provide guidance for the prevention of small-scale structure fatigue damage. Moreover, the distribution test of the noises is also carried out to verify the high order harmonics anomaly, and indicate that the jet noise spreads mainly towards downstream while screech towards upstream. In addition, the broadband shock-associated noise spreads vertical to the jet flow and exhibits the feature of directivity.

scholarly journals Aspect Ratio Driven Relationship between Nozzle Internal Flow and Supersonic Jet Mixing

Aerospace ◽  
2021 ◽  
Vol 8 (3) ◽  
pp. 78
Author(s):  
Kalyani Bhide ◽  
Kiran Siddappaji ◽  
Shaaban Abdallah
Keyword(s):  
Boundary Layer ◽  
Aspect Ratio ◽  
Nozzle Exit ◽  
Supersonic Jet ◽  
Internal Flow ◽  
Shear Stresses ◽  
Loss Mechanism ◽  
Potential Core ◽  
Jet Mixing ◽  
Aspect Ratios

This work attempts to connect internal flow to the exit flow and supersonic jet mixing in rectangular nozzles with low to high aspect ratios (AR). A series of low and high aspect ratio rectangular nozzles (design Mach number = 1.5) with sharp throats are numerically investigated using steady state Reynolds-averaged Navier−Stokes (RANS) computational fluid dynamics (CFD) with k-omega shear stress transport (SST) turbulence model. The numerical shadowgraph reveals stronger shocks at low ARs which become weaker with increasing AR due to less flow turning at the throat. Stronger shocks cause more aggressive gradients in the boundary layer resulting in higher wall shear stresses at the throat for low ARs. The boundary layer becomes thick at low ARs creating more aerodynamic blockage. The boundary layer exiting the nozzle transforms into a shear layer and grows thicker in the high AR nozzle with a smaller potential core length. The variation in the boundary layer growth on the minor and major axis is explained and its growth downstream the throat has a significant role in nozzle exit flow characteristics. The loss mechanism throughout the flow is shown as the entropy generated due to viscous dissipation and accounts for supersonic jet mixing. Axis switching phenomenon is also addressed by analyzing the streamwise vorticity fields at various locations downstream from the nozzle exit.

scholarly journals Investigation of efficacy of low length-to-diameter ratio and nozzle pressure ratio on base pressure in an abruptly expanded flow

2018 ◽  
Vol 172 ◽  
pp. 01004
Author(s):  
Fharrukh Ahmed ◽  
S. A. Khan
Keyword(s):  
Pressure Ratio ◽  
Flow Regulation ◽  
Base Pressure ◽  
Regulation Mechanism ◽  
Nozzle Pressure Ratio ◽  
Control Efficacy ◽  
Remarkable Change ◽  
Cross Sectional ◽  
Circular Duct ◽  
Nozzle Pressure

This study has been carried out to assess the efficacy of the flow regulations in the form of tiny jets to regulate the pressure in the base region of an abruptly expanded duct. Four tiny jets of 1mm diameter placed at 90° intervals at 6.5 mm distance from the main jet in the wake region of the base were employed as flow management mechanism. The experiments were conducted at the inertia level of M = 2.5 & 3.0. The jets from the nozzles were expanded abruptly into a circular duct with four cross-sectional areas of 2.56, 3.24, 4.84 and 6.25. The L/D ratio of the enlarged duct considered was from 10 to 1 and experiments were conducted for Nozzle Pressure Ratio (NPR) from 3 to 11. Since the jets Mach numbers are high and the highest NPR tested was 11 which imply that the flow remains over expanded, even though, with increase in the NPR, the level of over expansion will decrease. It is well known that for over expanded nozzles an oblique shock will be formed at the nozzle lip, which in turn will result in the increase of the base pressure once it passes through the shock wave. From the results it is observed that for the NPRs 3 and 5 there is no appreciable gain in the base pressure, and hence, control employed as tiny jets are not effective, however, at NPR 7, 9, and 11 there is remarkable change in the base pressure values. This clearly indicates that NPR plays a significant role to decide on the magnitude of the base pressure and the control efficacy of the flow regulation mechanism as the tiny jets. It is found that the present method of flow regulation mechanism can be used as effective regulator of the base flows in an abruptly expanded duct. The control does not alter the nature of the flow in the enlarge duct.

Optimum structure of a laval nozzle for an abrasive air jet based on nozzle pressure ratio

2020 ◽  
Vol 364 ◽  
pp. 343-362 ◽  
Author(s):  
Yong Liu ◽  
Juan Zhang ◽  
Jianping Wei ◽  
Xiaotian Liu
Keyword(s):  
Laval Nozzle ◽  
Pressure Ratio ◽  
Optimum Structure ◽  
Nozzle Pressure Ratio ◽  
Air Jet ◽  
Nozzle Pressure

Numerical analysis of supersonic co-flow jet with varying lip thickness

2021 ◽  
Vol ahead-of-print (ahead-of-print) ◽  
Author(s):  
Sathish Kumar K ◽  
Naren Shankar R ◽  
Anusindhiya K ◽  
Senthil Kumar B.R
Keyword(s):  
Mach Number ◽  
Total Pressure ◽  
Numerical Study ◽  
Pressure Ratio ◽  
Supersonic Nozzle ◽  
Experimental Result ◽  
Content Type ◽  
Jet Mixing ◽  
Mixing Characteristics ◽  
Jet Axis

Purpose This study aims to present the numerical study on supersonic jet mixing characteristics of the co-flow jet by varying lip thickness (LT). The LT chosen for the study is 2 mm, 7.75 mm and 15 mm. Design/methodology/approach The primary nozzle is designed for delivering Mach 2.0 jet, whereas the secondary nozzle is designed for delivering Mach 1.6 jet. The Nozzle pressure ratio chosen for the study is 3 and 5. To study the mixing characteristics of the co-flow jet, total pressure and Mach number measurements were taken along and normal to the jet axis. To validate the numerical results, the numerical total pressure values were also compared with the experimental result and it is proven to have a good agreement. Findings The results exhibit that, the 2 mm lip is shear dominant. The 7.75 mm and 15 mm lip is wake dominant. The jet interaction along the jet axis was also studied using the contours of total pressure, Mach number, turbulent kinetic energy and density gradient. The radial Mach number contours at the various axial location of the jet was also studied. Practical implications The effect of varying LT in exhaust nozzle plays a vital role in supersonic turbofan aircraft. Originality/value Supersonic co-flowing jet mixing effectiveness by varying the LT between the primary supersonic nozzle and the secondary supersonic nozzle has not been analyzed in the past.

Sign in / Sign up

Export Citation Format

Share Document