Quantitative depth estimation using analytic signal at low-latitude for ground gravity survey of Gbede, Oyo State

2021 ◽  
Vol 20 (2) ◽  
pp. 73-85
Author(s):  
G.O. Layade ◽  
O.O. Adewumi ◽  
V. Makinde ◽  
B.S. Bada
Keyword(s):  
Structural Model ◽  
Gravity Data ◽  
Thin Sheet ◽  
Bouguer Anomaly ◽  
Horizontal Cylinder ◽  
Analytic Signal ◽  
Gravity Survey ◽  
Depth Range ◽  
Low Latitude ◽  
Entire Area

This paper presents the insitu gravity survey of basement complex rock in Southwestern Nigeria. In the E-W direction, LaCoste and  Romberg Gravity Meter type G309 was used to carry out a ground gravity survey where ten traverses were established over a distance of 1000 m by 500 m with station spacing of 20m and a traverse interval of 50 m. Observed gravity values were corrected, analyzed and  interpreted quantitatively. The corrected bouguer gravity data were presented as bouguer anomaly graphs. Analytic Signal at low-latitude was adopted to compute the depth to source of iron-ore for a contact, a thin sheet (dyke) and a horizontal cylinder. The result revealed a depth range of 5.45 m-8.25 m for a contact, 9.44 m-14.29 m for a thin sheet (dyke) while a depth range of 12.31 m-18.05 m was estimated for a horizontal cylinder respectively. An average depth of 11.81±3.64 m was estimated for the entire area irrespective of the structural model, this was compared with published magnetic results of the study area and a small disparity of potential field measurements was recorded. The overall computed results signified the existence of iron mineral deposits at low depths across the study area.

Imaging depth, structure, and susceptibility from magnetic data: The advanced source-parameter imaging method

Geophysics ◽  
2005 ◽  
Vol 70 (4) ◽  
pp. L31-L38 ◽  
Author(s):  
Richard S. Smith ◽  
Ahmed Salem
Keyword(s):  
Source Parameters ◽  
Thin Sheet ◽  
Signal Amplitude ◽  
Horizontal Cylinder ◽  
Analytic Signal ◽  
Magnetic Data ◽  
Imaging Method ◽  
Structural Index ◽  
Synthetic Test ◽  
Vertical Contact

An important problem in the interpretation of magnetic data is quantifying the source parameters that describe the anomalous structure. We present a new method that uses various combinations of the local wavenumbers for estimating the depth and shape (structural index) of the structure. Because the estimates are derived from third derivatives of the magnetic data, they are noisy. However, there are multiple ways of calculating the depth and index, and these solutions can be averaged to give a stable estimate. Even so, a synthetic test shows that the results are erratic away from the locations where the analytic-signal amplitude is large. Hence, when we generate images of the depth and structural index, we make the results most visible where the analytic-signal amplitude is large and less visible where the signal is small. The advantage of the method is that estimates can be obtained at all locations on a profile and used to generate continuous profiles or images of the source parameters. This can be used to help identify the locations where interference might be corrupting the results. The structural index image can be used to determine the most appropriate type of model for an area. Assuming this model, it is possible to calculate the depth that would be consistent with the model and the data. Knowing both the depth and model, the analytic-signal amplitude can be converted to apparent susceptibility. If a vertical-contact model is assumed, the susceptibility contrast across the contact can be imaged. For the thin-sheet and horizontal-cylinder models, we can image the susceptibility-thickness and susceptibility-area products, respectively.

Shape and depth solutions from gravity data using correlation factors between successive least‐squares residuals

Geophysics ◽  
1993 ◽  
Vol 58 (12) ◽  
pp. 1785-1791 ◽  
Author(s):  
El‐Sayed M. Abdelrahman ◽  
Hesham M. El‐Araby
Keyword(s):  
Least Squares ◽  
Shape Factor ◽  
Gravity Data ◽  
Bouguer Anomaly ◽  
Vertical Cylinder ◽  
Gravity Anomalies ◽  
Horizontal Cylinder ◽  
Amplitude Coefficient ◽  
Regional Component ◽  
Correlation Factors

The gravity anomaly expression produced by most geologic structures can be represented by a continuous function in both shape (shape factor) and depth variables with an amplitude coefficient related to the mass. Correlation factors between successive least‐squares residual gravity anomalies from a buried vertical cylinder, horizontal cylinder, and sphere are used to determine the shape and depth of the buried geologic structure. For each shape factor value, the depth is determined automatically from the correlation value. The computed depths are plotted against the shape factor representing a continuous correlation curve. The solution for the shape and depth of the buried structure is read at the common intersection of correlation curves. This method can be applied to a Bouguer anomaly profile consisting of a residual component caused by local structure and a regional component. This is a powerful technique for automatically separating the Bouguer data into residual and regional polynomial components. This method is tested on theoretical examples and a field example. In both cases, the results obtained are in good agreement with drilling results.

Gravity Survey of King Fahd University of Petroleum and Minerals Dammam Dome, Saudi Arabia

2021 ◽  
Author(s):  
Pantelis Soupios ◽  
Alexandros Stampolidis ◽  
Maurizio Fedi ◽  
SanLinn Kaka ◽  
Khalid Al-Ramadan ◽  
...  
Keyword(s):  
Saudi Arabia ◽  
Gravity Data ◽  
Bouguer Anomaly ◽  
3D Models ◽  
Low Noise ◽  
Gravity Survey ◽  
Differential Gps ◽  
Gravity Measurements ◽  
Anomaly Map ◽  
Bouguer Anomaly Map

Abstract The study area is a part of Dammam Dome that is situated at King Fahd University of Petroleum & Minerals (KFUPM) campus, Dhahran, Kingdom of Saudi Arabia. The gravity survey was conducted as a pilot case study to explore part of Dammam Dome in greater detail. Gravity data were collected solely during night hours due to low noise levels. A significant part of the survey was conducted during the summer holiday period, , when there was no student are on campus. A total of 235 gravity measurements were made using a Scintrex CG5 gravitometer, while a Trimble R10+ differential GPS (DGPS) was used to measure the stations’ location and elevation with the highest accuracy. All gravity data were reduced using several algorithms, and their outcomes were cross-compared. The Complete Bouguer anomaly map for the campus was then generated. Several enhancement filters including edged detection and shallow to deeper source separation were applied. Data were inverted, and 2.5D and 3D models were created to image the subsurface conditions. The main purpose of this study is to better understand the subsurface geology, tectonic settings of the Dammam Dome by applying the high-resolution gravity method before carrying out any comprehensive geophysical (seismic) 3D survey.

scholarly journals Gravity Analysis for Subsurface Characterization and Depth Estimation of Muda River Basin, Kedah, Peninsular Malaysia

2021 ◽  
Vol 11 (14) ◽  
pp. 6363
Author(s):  
Muhammad Noor Amin Zakariah ◽  
Norsyafina Roslan ◽  
Norasiah Sulaiman ◽  
Sean Cheong Heng Lee ◽  
Umar Hamzah ◽  
...  
Keyword(s):  
River Basin ◽  
Rock Type ◽  
Gravity Data ◽  
Power Spectral Analysis ◽  
Depth Estimation ◽  
Structural Features ◽  
Peninsular Malaysia ◽  
Gravity Survey ◽  
Basement Rock ◽  
Geophysical Techniques

Gravity survey is one of the passive geophysical techniques commonly used to delineate geological formations, especially in determining basement rock and the overlying deposit. Geologically, the study area is made up of thick quaternary alluvium deposited on top of the older basement rock. The Muda River basin constitutes, approximately, of more than 300 m of thick quaternary alluvium overlying the unknown basement rock type. Previous studies, including drilling and geo-electrical resistivity surveys, were conducted in the area but none of them managed to conclusively determine the basement rock type and depth precisely. Hence, a regional gravity survey was conducted to determine the thickness of the quaternary sediments prior to assessing the sustainability of the Muda River basin. Gravity readings were made at 347 gravity stations spaced at 3–5 km intervals using Scintrex CG-3 covering an area and a perimeter of 9000 km2 and 730 km, respectively. The gravity data were then conventionally reduced for drift, free air, latitude, Bouguer, and terrain corrections. These data were then consequently analyzed to generate Bouguer, regional and total horizontal derivative (THD) anomaly maps for qualitative and quantitative interpretations. The Bouguer gravity anomaly map shows low gravity values in the north-eastern part of the study area interpreted as representing the Main Range granitic body, while relatively higher gravity values observed in the south-western part are interpreted as representing sedimentary rocks of Semanggol and Mahang formations. Patterns observed in the THD anomaly and Euler deconvolution maps closely resembled the presence of structural features such as fault lineaments dominantly trending along NW-SE and NE-SW like the trends of topographic lineaments in the study area. Based on power spectral analysis of the gravity data, the average depth of shallow body, representing alluvium, and deep body, representing underlying rock formations, are 0.5 km and 1.2 km, respectively. The thickness of Quaternary sediment and the depth of sedimentary formation can be more precisely estimated by other geophysical techniques such as the seismic reflection survey.

scholarly journals Geometrical Characterisation of the Mamfe Basin, Cameroon, from the Earth, Gravitational Model (EGM 2008)

2018 ◽  
Vol 7 (1) ◽  
pp. 94
Author(s):  
Anatole Eugene Djieto Lordon ◽  
Mbohlieu YOSSA ◽  
Christopher M Agyingi ◽  
Yves Shandini ◽  
Thierry Stephane Kuisseu
Keyword(s):  
Average Length ◽  
Gravity Data ◽  
Bouguer Anomaly ◽  
Igneous Rocks ◽  
Average Depth ◽  
The Earth ◽  
Gravitational Model ◽  
Petroleum Generation ◽  
Anomaly Map ◽  
Bouguer Anomaly Map

Gravimetric studies using the ETOPO1-corrected high resolution satellite-based EGM2008 gravity data was used to define the surface extent, depth to basement and shape of the Mamfe basin. The Bouguer anomaly map was produced in Surfer 11.0. The Fast Fourier Transformed data was analyzed by spectral analysis to remove the effect of the regional bodies in the study area. The residual anomaly map obtained was compared with the known geology of the study area, and this showed that the gravity highs correspond to the metamorphic and igneous rocks while the gravity lows match with Cretaceous sediments. Three profiles were drawn on the residual anomaly map along which 2D models of the Mamfe basin were drawn. The modeling was completed in Grav2dc v2.06 software which uses the Talwini’s algorithm and the resulting models gave the depth to basement and the shape of the basement along the profiles. After processing and interpretation, it was deduced that the Mamfe basin has an average length and width of 77.6 km and 29.2 km respectively, an average depth to basement of 5 km and an overall U-shape basement. These dimensions (especially the depth) theoretically create the depth and temperature conditions for petroleum generation. 

scholarly journals DETERMINATION AND MAPPING OF THE TERRESTRIAL GRAVITY ANOMALIES IN THE MOUNTAINOUS AREAS OF IRAQ

2021 ◽  
Vol 6 (24) ◽  
pp. 213-225
Author(s):  
Shazad Jamal Jalal ◽  
Tajul Ariffin Musa ◽  
Ami Hassan Md Din ◽  
Wan Anom Wan Aris
Keyword(s):  
Gravity Data ◽  
Physical Geodesy ◽  
Gravity Anomalies ◽  
Gravity Survey ◽  
Mountainous Areas ◽  
Entire Study ◽  
Terrestrial Gravity ◽  
The Past ◽  
Regional Gravity ◽  
Entire Study Area

Gravity data and computing gravity anomalies are regarded as vital for both geophysics and physical geodesy fields. The mountainous areas of Iraq are characterized by the lack of regional gravity data because gravity surveys are rarely performed in the past four decades due to the Iraq-Iran war and the internal unstable political situation of this particular region. In addition, the formal map of the available terrestrial gravity which was published by the French Database of Bureau Gravimetrique International (International Gravimetric Bureau-in English) (BGI), introduces Iraq and the study area as a remote area and in white color because of the unavailability of gravity data. However, a dense and local (not regional) gravity data is available which was conducted by geophysics researchers 13 years ago. Therefore, the regional gravity survey of 160 gravity points was performed by the authors at an average 11 km apart, which was covers the whole area of Sulaymaniyah Governorate (part of the mountainous areas of Iraq). In spite of Although the risk of mine fields within the study area, suitable safe routes as well as a helicopter was used for the gravity survey of several points on the top of mountains. The survey was conducted via Lacoste and Romberg geodetic gravimeter and GPS handheld. The objective of the study is to determine and map the gravity anomalies for the entire study area, the data of which would assist different geosciences applications.

scholarly journals Analytic Signal Depth from High Resolution Aeromagnetic Data over the Gongola Basin Upper Benue Trough Northeastern Nigeria

2021 ◽  
Vol 25 (4) ◽  
pp. 585-590
Author(s):  
H. Musa ◽  
N.E. Bassey ◽  
R. Bello
Keyword(s):  
High Resolution ◽  
Magnetic Structure ◽  
Horizontal Cylinder ◽  
Analytic Signal ◽  
Aeromagnetic Data ◽  
Polynomial Fitting ◽  
Benue Trough ◽  
Local Maxima ◽  
Depth Determination ◽  
Programming Software

The study of high-resolution aeromagnetic data was carried out over the Gongola basin, upper Benue trough, northeastern Nigeria, for analytic signal depth determination. Total intensity magnetic map obtained from the data using the Oasis Montaj TM programming software was used to get the residual map by polynomial fitting, from where the analytic signal was obtained with the use of anomaly width at half the amplitude (X1/2). This was used to carry out depth estimations over the study area. The results showed that it peaks over the magnetic structure with local maxima over its edges (boundaries or contact), and the amplitude is simply related to magnetization, likewise results also showed that the depth estimates were in the range of 1.2 to 5.9 km and were calculated for contact, dyke/sill and horizontal cylinder respectively. The lowest values are from DD profiles, while the highs are from AA profiles. This work is important in identifying dykes, contacts and intrusives over an area.

scholarly journals Structural model of the Northern Latium volcanic area constrained by MT, gravity and aeromagnetic data

1997 ◽  
Vol 40 (5) ◽  
Author(s):  
P. Capuano ◽  
G. Florio ◽  
P. Gasparini
Keyword(s):  
Structural Model ◽  
Gravity Data ◽  
Gravity Anomalies ◽  
Volcanic Area ◽  
Aeromagnetic Data ◽  
Geothermal Exploration ◽  
Magnetotelluric Soundings ◽  
Aeromagnetic Anomalies ◽  
Deep Boreholes

The results of about 120 magnetotelluric soundings carried out in the Vulsini, Vico and Sabatini volcanic areas were modeled along with Bouguer and aeromagnetic anomalies to reconstruct a model of the structure of the shallow (less than 5 km of depth) crust. The interpretations were constrained by the information gathered from the deep boreholes drilled for geothermal exploration. MT and aeromagnetic anomalies allow the depth to the top of the sedimentary basement and the thickness of the volcanic layer to be inferred. Gravity anomalies are strongly affected by the variations of morphology of the top of the sedimentary basement, consisting of a Tertiary flysch, and of the interface with the underlying Mesozoic carbonates. Gravity data have also been used to extrapolate the thickness of the neogenic unit indicated by some boreholes. There is no evidence for other important density and susceptibility heterogeneities and deeper sources of magnetic and/or gravity anomalies in all the surveyed area.

scholarly journals Lineament Extraction using Gravity Data in the Citarum Watershed

2021 ◽  
Vol 53 (1) ◽  
Author(s):  
Gumilar Utamas Nugraha ◽  
Karit Lumban Goal ◽  
Lina Handayani ◽  
Rachmat Fajar Lubis
Keyword(s):  
Gravity Data ◽  
Bouguer Anomaly ◽  
High Density ◽  
Low Density ◽  
Residual Value ◽  
Satellite Gravity ◽  
Structural Weakness ◽  
Major Trend ◽  
Lineament Extraction ◽  
Butterworth Filters

Lineament is one of the most important features showing subsurface elements or structural weakness such as faults. This study aims to identify subsurface lineament patterns using automatic lineament in Citarum watershed with gravity data. Satellite gravity data were used to generate a sub-surface lineament. Satellite gravity data corrected using Bouguer and terrain correction to obtain a complete Bouguer anomaly value. Butterworth filters were used to separate regional and residual anomaly from the complete Bouguer anomaly value. Residual anomaly gravity data used to analyze sub-surface lineament. Lineament generated using Line module in PCI Geomatica to obtain sub-surface lineament from gravity residual value. The orientations of lineaments and fault lines were created by using rose diagrams. The main trends observed in the lineament map could be recognized in these diagrams, showing a strongly major trend in NW-SE, and the subdominant directions were in N-S. Area with a high density of lineament located at the Southern part of the study area. High-density lineament might be correlated with fractured volcanic rock upstream of the Citarum watershed, meanwhile, low-density lineament is associated with low-density sediment. The high-density fracture might be associated with intensive tectonics and volcanism.

3D Gravity modeling of the volcanic island of Surtsey, Iceland

2021 ◽  
Author(s):  
sara sayyadi ◽  
Magnús T. Gudmundsson ◽  
Thórdís Högnadóttir ◽  
James White ◽  
Joaquín M.C. Belart ◽  
...  
Keyword(s):  
Sea Level ◽  
Gravity Data ◽  
Bouguer Anomaly ◽  
Gravity Modeling ◽  
Gravity Station ◽  
Effusive Activity ◽  
3D Gravity ◽  
Anomaly Map ◽  
Bouguer Anomaly Map ◽  
Drill Cores

<p>The formation of the oceanic island Surtsey in the shallow ocean off the south coast of Iceland in 1963-1967 remains one of the best-studied examples of basaltic emergent volcanism to date. The island was built by both explosive, phreatomagmatic phases and by effusive activity forming lava shields covering parts of the explosively formed tuff cones.  Constraints on the subsurface structure of Surtsey achieved mainly based on the documented evolution during eruption and from drill cores in 1979 and in the ICDP-supported SUSTAIN drilling expedition in 2017(an inclined hole, directed 35° from the vertical). The 2017 drilling confirmed the existence of a diatreme, cut into the sedimentary pre-eruption seafloor (Jackson et al., 2019). </p><p>We use 3D-gravity modeling, constrained by the stratigraphy from the drillholes to study the structure of the island and the underlying diatreme.  Detailed gravity data were obtained on Surtsey in July 2014 with a gravity station spacing of ~100 m. Density measurements for the seafloor sedimentary and tephra samples of the surface were carried out using the ASTM1 protocol. By comparing the results with specific gravity measurements of cores from drillhole in 2017, a density contrast of about 200 kg m<sup>-3</sup> was found between the lapilli tuffs of the diatreme and the seafloor sediments.  Our approach is to divide the island into four main units of distinct density: (1) tuffs above sea level, (2) tuffs below sea level, (3) lavas above sea level, and (4) a lava delta below sea level, composed of breccias over which the lava advanced during the effusive eruption.  The boundaries between the bodies are defined from the eruption history and mapping done during the eruption, aided by the drill cores. </p><p>A complete Bouguer anomaly map is obtained by calculating a total terrain correction by applying the Nagy formula to dense DEMs (5 m spacing out to 1.2 km from station, 200 m spacing between 1.2 km and 50 km) of both island topography and ocean bathymetry.  Through the application of both forward and inverse modeling, using the GM-SYS 3D software, the results provide a 3-D model of the island itself, as well as constraints on diatreme shape and depth.</p>

Sign in / Sign up

Export Citation Format

Share Document