scholarly journals Kinetics, Isotherms and Thermodynamic Studies on Removal of Divalent Copper using Mallet Flower Leaf Powder as Bio-Adsorbent

2021 ◽  
Vol 18 (24) ◽  
pp. 1431
Author(s):  
Devarapalli Venkata Padma ◽  
Susarla Venkata Ananta Rama Sastry
Keyword(s):  
Experimental Data ◽  
Atomic Absorption ◽  
Kinetic Data ◽  
Maximum Adsorption Capacity ◽  
Divalent Copper ◽  
Order Model ◽  
Leaf Powder ◽  
Pseudo Second Order ◽  
Best Fit ◽  
Agitation Time

The effectiveness and efficacy of Mallet Flower Leaf Powder (MFLP) as a bio-sorbent for the removal of heavy metal copper ions from the aqueous solutions have been studied. Experiments were conducted varying the pH, agitation time, temperature, biosorbent size and dosage as parameters. Speed of the mixing is kept at 200 rpm. The analysis of copper was done by using Atomic Absorption Spectrophotometer (AAS). The adsorption of copper was found to be dependent on pH and a maximum removal of 98.78 % was obtained at an optimum pH of 6.0. The optimum biosorbent dosage was 1 g for an agitation time of 40 min. The biosorption data obtained were validated for the best isotherm. The data collected were verified with the available adsorption isotherms. Experimental data obtained was well represented by Langmuir (RL = 0.161, qm = 5.96 mg/g, R2 = 0.9142), Freundlich (n = 0.64, Kf  = 0.79L/g, R2 = 0.9995) and Tempkin (R2 = 0.9083, bT = 267.63) isotherms, indicating favorable biosorption. The experimental data obtained were tested for the best fit and the Freundlich Model has yielded the best correlation with the highest regression coefficient, R2 = 0.9844. Kinetic data has also been presented using thermodynamic analysis and the pseudo second order model was found to be the best fit with a correlation coefficient of 0.999. For the removal of copper from the solution, bioadsorbent showed a maximum adsorption capacity of 5.96 mg/g. HIGHLIGHTS Removal of divalent copper from the aqueous solution using Mallet Flower Leaf powder Atomic Absorption Spectroscopy, Scanning Electron Microscopy and Fourier transform infrared analysis were used to characterize the Mallet Flower Leaf Powder Kinetic data has been presented using thermodynamic analysis and the pseudo second order model was found to be the best fit with a correlation coefficient of 0.999 The maximum adsorption capacity of MFLP for copper was found to be 5.96 mg/gm GRAPHICAL ABSTRACT

scholarly journals Simultaneous Adsorption of Cr(VI) and Phenol from Binary Mixture Using Iron Incorporated Rice Husk: Insight to Multicomponent Equilibrium Isotherm

2016 ◽  
Vol 2016 ◽  
pp. 1-11 ◽  
Author(s):  
Ankur Gupta ◽  
Chandrajit Balomajumder
Keyword(s):  
Experimental Data ◽  
Rice Husk ◽  
Low Cost ◽  
Binary Solution ◽  
Multicomponent System ◽  
Isotherm Models ◽  
Maximum Adsorption Capacity ◽  
Order Model ◽  
Adsorption Isotherm Models ◽  
Pseudo Second Order

Fe modified rice husk was prepared as a low cost biosorbent for the removal of Cr(VI) and phenol both singly and in combination from single and binary simulated synthetic waste water. Rice husk was modified by treating with FeSO4·7H2O. The results showed that impregnation of iron onto the surface of rice husk improved the adsorption capability of both Cr(VI) and phenol. The effects of process parameters for multicomponent system such as pH, adsorbent dose, and contact time onto the percentage removal of both Cr(VI) and phenol were investigated. The experimental data for the adsorption of both Cr(VI) and phenol onto the surface of Fe modified rice husk applied to various kinetic and adsorption isotherm models. Multicomponent isotherm models such as Nonmodified Langmuir, Modified Langmuir, Extended Langmuir, Extended Freundlich, Competitive Nonmodified Redlich Peterson, Competitive Modified Redlich Peterson were applied. The results show that Extended Freundlich model best described the experimental data for both Cr(VI) and phenol from binary solution. Pseudo second-order model agreed well with Cr(VI) while pseudo first-order model agreed well with phenol. Maximum adsorption capacity in synthetic binary solution of Cr(VI) and phenol was found to be 36.3817 mg g−1for Cr(VI) and 6.569 mg g−1for phenol, respectively.

Adsorption of Ce(III) by Magnetic Chitosan/Yeast Composites from Aqueous Solution: Kinetic and Equilibrium Studies

2013 ◽  
Vol 316-317 ◽  
pp. 391-394 ◽  
Author(s):  
Hong Xiang Ou ◽  
Wei Bai Bian ◽  
Xiang Mei Weng ◽  
Wei Hong Huang ◽  
Yun Lei Zhang
Keyword(s):  
Experimental Data ◽  
Kinetic Data ◽  
Second Order ◽  
Maximum Adsorption Capacity ◽  
Equilibrium Studies ◽  
Magnetic Chitosan ◽  
Effects Of Ph ◽  
Pseudo Second Order ◽  
Magnetic Stability ◽  
Ph Range

Magnetic chitosan/yeast(MCY) composites were prepared and applied to adsorb Ce(III) ions from aqueous solutions. The effects of pH, contact time and initial concentration were examined, and the hematite leakage was also studied. The optimum pH was 5.5. MCY composites had magnetic stability (especially over pH range of 4.5~7.0). The kinetic data were investigated by pseudo-first-order and pseudo-second-order models. The kinetic data were better fitted to the pseudo-second-order model. Experimental data were fitted with the Langmuir and Freundlich models to analyze the equilibrium isotherms. The Freundlich model was better to describe the experimental data. The maximum adsorption capacity calculated by Langmuir isotherm was 73.53 mg/g.

Removal of As(V) and As(III) from water with a PEI-modified fungal biomass

2007 ◽  
Vol 55 (1-2) ◽  
pp. 177-185 ◽  
Author(s):  
S. Deng ◽  
Y.P. Ting
Keyword(s):  
Experimental Data ◽  
Surface Modification ◽  
Penicillium Chrysogenum ◽  
Fungal Biomass ◽  
Kinetic Data ◽  
Arsenic Species ◽  
Langmuir Equation ◽  
Order Model ◽  
Pseudo Second Order ◽  
Amine Groups

A novel biosorbent was prepared by chemically grafting polyethylenimine (PEI) on the fungal biomass of Penicillium chrysogenum through a two-step reaction. The PEI-modified biomass was found to possess zero zeta potential at pH 10.4. Owing to the protonation of amine groups on the biosorbent surface, the biosorbent is favourable for the removal of anionic arsenic species in water. The sorption capacity for As(V) at pH 3 increased by 5.7-fold after surface modification. The sorption performances including kinetics and isotherm were investigated and several models were used to describe the experimental data. The pseudo-second-order model described the kinetic data better, while the Langmuir equation was the better model to fit the isotherm data. The corresponding thermodynamic parameters for As(V) and As(III) sorption were also calculated.

scholarly journals Abatement of Azo Dye from Wastewater Using Bimetal-Chitosan

2013 ◽  
Vol 2013 ◽  
pp. 1-10 ◽  
Author(s):  
Ghorban Asgari ◽  
Bahman Ramavandi ◽  
Sima Farjadfard
Keyword(s):  
Experimental Data ◽  
Azo Dye ◽  
Dye Adsorption ◽  
Maximum Adsorption Capacity ◽  
Orange Ii ◽  
Dye Wastewater ◽  
Effects Of Ph ◽  
Pseudo Second Order ◽  
Time Required ◽  
Best Fit

We introduce a new adsorbent, bimetallic chitosan particle (BCP) that is successfully synthesized and applied to remove the orange II dye from wastewater. The effects of pH, BCP quantity, and contact time are initially verified on the basis of the percentage of orange II removed from the wastewater. Experimental data reveal that the Cu/Mg bimetal and chitosan have a synergistic effect on the adsorption process of the adsorbate, where the dye adsorption by Cu/Mg bimetal, chitosan alone, and bimetal-chitosan is 10, 49, and 99.5%, respectively. The time required for the complete decolorization of orange II by 1 mg/L of BCP is 10 min. The Langmuir model is the best fit for the experimental data, which attains a maximum adsorption capacity of 384.6 mg/g. The consideration of the kinetic behavior indicates that the adsorption of orange II onto the BCP fits best with the pseudo-second-order and Elovich models. Further, the simulated azo dye wastewater can be effectively treated using a relatively low quantity of the adsorbent, 1 mg/L, within a short reaction time of 20 min. Overall, the use of BCP can be considered a promising method for eliminating the azo dye from wastewater effectively.

Adsorption of the Blue Dye Reactive Remazol RN in Cellulosic Materials

2014 ◽  
Vol 775-776 ◽  
pp. 749-754
Author(s):  
Mirna Sales Loiola Rosa ◽  
Marcos Pereira Silva ◽  
Alan Icaro Morais ◽  
Maria Rita de Morais Chaves Santos ◽  
Edson Cavalcanti Silva Filho ◽  
...  
Keyword(s):  
Low Cost ◽  
Langmuir Model ◽  
Blue Dye ◽  
Maximum Adsorption Capacity ◽  
Order Model ◽  
Textile Waste ◽  
Pseudo Second Order ◽  
Filter Papers ◽  
Best Fit ◽  
The Ideal

The disposal of textile waste in water bodies is exacerbating environmental problems, which led scientists to seek natural materials to develop more sustainable ways. Searching for low cost materials was used to remove the dye in two cellulosic sources (filter papers of different brands). The papers were characterized by XRD which confirmed crystallographic profile similar to cellulose. With the aim of optimizing the best conditions, various tests were performed, where the ideal time was 180 minutes for the paper 1 and 240 minutes for the second paper, both by adjusting the pseudo second-order model. The other parameters studied was the pH, adsorbate-adsorbent systems which have maximum adsorption capacity of 2.76 mg / g at pH 2.02 and 2 mg / g at pH 11 for the paper 1 and 10.57 mg / g pH 4 and 2 mg / g at pH 11 for the paper 2. Both adsorbents had the best fit to the Langmuir model in pHs 2 and 11 at the temperature of 298 K.

Methylene Blue Adsorption onto NaOH Treated Leucaena leucocephala Leaf Power

2015 ◽  
Vol 752-753 ◽  
pp. 251-256
Author(s):  
Megat Ahmad Kamal Megat Hanafiah ◽  
Noor Fhadzilah Mansur ◽  
Wan Mohd Nazri Wan Ab Rahman ◽  
Mardhiah Ismail
Keyword(s):  
Methylene Blue ◽  
Industrial Wastewater ◽  
Adsorption Equilibrium ◽  
Langmuir Model ◽  
Maximum Adsorption Capacity ◽  
Order Model ◽  
Adsorption Parameters ◽  
Leaf Powder ◽  
Pseudo Second Order ◽  
Kinetics And Isotherms

The potential of sodium hydroxide (NaOH) modified Petai Belalang (Leucaenaleucocephala) leaf powder as a biosorbent for methylene blue removal from aqueous solutions was investigated. Adsorption parameters studied include initial dye concentration, pH, dosage, kinetics and isotherms. The pHzpc of chemically treated Leucaenaleucocephala leaf powder was 7.50 and adsorption equilibrium time was achieved after 60 min. The kinetic data was best represented by the pseudo-second order model. The maximum adsorption capacity predicted from Langmuir model was 208.33 mg g-1. This work indicated that NaOH treated Leucaenaleucocephala leaf powder can be an attractive biosorbent for MB removal from diluted industrial wastewater.

scholarly journals Brasil nut mesocarp (Bertholletia excels) as a Biomass Source for Activated Carbon Production: Correlation Between Thermal Treatment and Adsorption Performance

2021 ◽  
Vol 12 (4) ◽  
pp. 4584-4596
Keyword(s):  
Activated Carbon ◽  
Maximum Adsorption Capacity ◽  
Brazil Nut ◽  
Order Model ◽  
X Ray ◽  
Adsorption Performance ◽  
Carbon Production ◽  
Pseudo Second Order ◽  
Adsorption Desorption ◽  
Best Fit

The activated carbon investigated in this work was produced from the extractive residues of Brazil nut processing, more specifically from the mesocarp of the Amazonian fruit. The process was performed by muffle pyrolysis, with ZnCl2 impregnation, at 400 and 500 °C. All samples were characterized by X-ray diffractometry, thermogravimetry, CHNS elemental analysis, scanning electron microscopy, and adsorption/desorption of N2. The results were promissory, with 99% removal of methylene blue for the CA25 material, which has a surface area of 1236 m2 g-1, much higher than commercial coal (CAC, 618 m2 g-1). The adsorption kinetics best fit the pseudo-second-order model for all materials. The maximum adsorption capacity obtained was 195.3 mg g-1. Therefore, the extractive residue of Brazil nut has excellent potential for the development of activated carbon, which can be used effectively to mediate environmental contamination in a given aqueous medium.

Sorption properties of Amberlite XAD 7 functionalized with sodium β-glycerophosphate

2016 ◽  
Vol 88 (12) ◽  
pp. 1143-1154
Author(s):  
Andreea Gabor ◽  
Corneliu Mircea Davidescu ◽  
Adina Negrea ◽  
Mihaela Ciopec ◽  
Cornelia Muntean ◽  
...  
Keyword(s):  
Adsorption Process ◽  
Ph Value ◽  
Sorption Properties ◽  
Maximum Adsorption Capacity ◽  
Order Model ◽  
X Ray ◽  
Equilibrium Data ◽  
Pseudo Second Order ◽  
Best Fit ◽  
Efficient Adsorbent

Abstract This paper presents the sorption properties of a new adsorbent material prepared by impregnating Amberlite XAD 7 polymer with sodium β-glycerophosphate. For impregnation, the pellicular vacuum solvent vaporization method was employed. The functionalization was evidenced by energy dispersive X-ray analysis. The usefulness of this material and its performances were studied for the adsorption of the rare earth element La(III) in batch experiments. The influence of various parameters affecting the adsorption of lanthanum like contact time, initial concentration, pH value, and temperature was studied. The kinetic of the adsorption process was best described by the pseudo-second-order model. Sips isotherm was found to be the best fit of the equilibrium data. The maximum adsorption capacity of the functionalized material was of 33.8 mg La(III)/g. The values of thermodynamic parameters (ΔGo, ΔHo, ΔSo) showed that the adsorption process was endothermic and spontaneous. The results proved that Amberlite XAD 7 functionalized with sodium β-glycerophosphate is an efficient adsorbent for the removal of La(III) ions from aqueous solutions. Quantum chemistry was performed using Spartan software.

scholarly journals Optimization of the sorption of selected polycyclic aromatic hydrocarbons by regenerable graphene wool

2019 ◽  
Vol 80 (10) ◽  
pp. 1931-1943 ◽  
Author(s):  
Adedapo O. Adeola ◽  
Patricia B. C. Forbes
Keyword(s):  
Polycyclic Aromatic Hydrocarbons ◽  
Adsorption Capacity ◽  
Aromatic Hydrocarbons ◽  
Kinetic Data ◽  
Second Order ◽  
Maximum Adsorption Capacity ◽  
Order Kinetic ◽  
Polycyclic Aromatic ◽  
Pseudo Second Order ◽  
Best Fit

Abstract A novel graphene wool (GW) material was used as adsorbent for the removal of phenanthrene (PHEN) and pyrene (PYR) from aqueous solution. Adsorption kinetics, adsorption isotherms, thermodynamics of adsorption and effect of pH, ionic strength, and temperature on the adsorption of PHEN and PYR onto GW were comprehensively investigated. Isothermal and kinetic experimental data were fitted to Langmuir, Freundlich, Temkin, Sips and Dubinin–Radushkevich models, as well as pseudo-first-order and pseudo-second-order kinetic models. The adsorption kinetic data best fit the pseudo-second-order kinetic model for PHEN and PYR sorption with R2 value >0.999, whilst the Sips model best fit isotherm data. Kinetic data revealed that 24 hr of contact between adsorbent and polycyclic aromatic hydrocarbons (PAHs) was sufficient for maximum adsorption, where the Langmuir maximum adsorption capacity of GW for PHEN and PYR was 5 and 20 mg g−1 and the optimum removal efficiency was 99.9% and 99.1%, respectively. Thermodynamic experiments revealed that adsorption processes were endothermic and spontaneous. Desorption experiments indicated that irreversible sorption occurred with a hysteresis index greater that zero for both PAHs. The high adsorption capacity and potential reusability of GW makes it a very attractive material for removal of hydrophobic organic micro-pollutants from water.

Adsorption Isotherms and Kinetic Models for Congo Red Adsorption on Ca-Al Layer Double Hydroxide Adsorbent

2019 ◽  
Vol 298 ◽  
pp. 128-132 ◽  
Author(s):  
To Uyen T. Dao ◽  
Hong Tham T. Nguyen ◽  
Do Trung Sy ◽  
Khoa Hien Nguyen ◽  
Anh Tien Nguyen ◽  
...  
Keyword(s):  
Kinetic Data ◽  
Adsorption Process ◽  
Single Layer ◽  
Chemical Processes ◽  
Maximum Adsorption Capacity ◽  
Order Model ◽  
Layer Double Hydroxide ◽  
Layer Adsorption ◽  
Pseudo Second Order ◽  
Double Hydroxide

The equilibrium and physicochemical properties of the Ca-Al LDH material were determined in this study. Kinetic data were analyzed using isothermal models including Langmuir, Freundlich, Temkin and Dubinin–Radushkevich. Adsorption behavior is well described by the Langmuir isotherm and the pseudo-second-order model. The maximum adsorption capacity of CR on Ca-Al LDH is found to be 72.569 mg/g. The uptake results indicated that the adsorption process was controlled by chemical processes and single-layer adsorption. Due to, the Ca-Al LDH material may be become an effective adsorbent for removal CR dye in aqueous solution.

Sign in / Sign up

Export Citation Format

Share Document