Exploration of orogenic, fault-hosted geothermal systems using an integrated, multi-disciplinary approach.

Author(s):  
Carbajal-Martínez Daniel ◽  
Loïc Peiffer ◽  
Larryn W. Diamond ◽  
John M. Fletcher ◽  
Claudio Inguaggiato ◽  
...  

<p>Non-magmatic, orogenic geothermal systems are recognized as significant energy resources for electricity production or direct uses. This study focuses on the non-magmatic geothermal system hosted by the Agua Blanca fault, Ensenada, Mexico. The Agua Blanca fault is a 140 km long transtensional structure with segments recording up to 11 km of dextral strike-slip displacement and normal throws of up to 0.65 km. We have identified at least seven geothermal areas manifested by hot springs discharging at temperatures ranging from 38 °C to 107 °C. These systems involve topography-driven infiltration of meteoric water deep into the Agua Blanca fault and exfiltration of the heated water at valley floors and along a local beach known as La Jolla.</p><p>For this contribution, we present recent and ongoing exploration activities aiming to (i) obtain a fundamental understanding of the governing thermal-hydraulic-chemical processes controlling the circulation of meteoric water in the hydrothermally active fault system and (ii) quantify the natural discharge rate and its respective advective heat output. Chemical and isotopic analyses of thermal springs and seismic epicenters' location reveal that meteoric water penetrates between 5 to 10 km deep into the brittle orogenic crystalline basement and thereby attains temperatures between 105 and 215 °C. Interestingly, the deepest circulation and hottest reservoir temperatures occur where the extensional displacement along the fault shows maximum values. However, our data provide no evidence that meteoric water infiltrates beyond the brittle-ductile zone in the crust (12-18 km).</p><p>For the La Jolla beach thermal area, we have quantified the advective heat output from thermal images acquired with an unmanned aerial vehicle equipped with a thermal camera and from water flow and direct temperature measurements. The total thermal water discharge is 330 ± 44 L s<sup>-1</sup> and occurs over a surface area of 2804 m<sup>2</sup> at temperatures up to 52 °C. At 20 cm depth, the temperature is as high as 93 °C. These observations collectively imply a current heat output of 40.5 ± 5.2 MW<sub>t </sub>(Carbajal-Martínez et al., 2020). We are currently estimating the shape and magnitude of the subsurface thermal anomaly at La Jolla beach by performing coupled thermal-hydraulic-chemical simulations using the code Toughreact.</p><p>We conclude that meteoric water circulation through the Agua Blanca fault system reflects the interplay between the permeability distribution along the fault system and the rugged regional topography. Under ideal conditions such as at La Jolla beach, such circulation generates rather large thermal outputs that could supply the thermal energy for a multi-effect distillation desalinization plant and contribute to cover the shortage of fresh water in Ensenada.</p>

Author(s):  
Wahyu Hidayat ◽  
Hafiz Hamdalah ◽  
Hana Aulia K

<p><span style="font-size: medium;">Satu daerah yang diduga terdapat sistem panasbumi adalah daerah Gunung Pancar, Bogor, Jawa Barat.<em> </em>Beberapa mata air panas yang muncul di sekitar daerah penelitian memperkuat dugaan adanya sistem panasbumi di daerah tersebut<em>.</em> Metode geofisika yang dapat digunakan untuk mengidentifikasi sistem panasbumi adalah Metode Audio Magnetotelurik (AMT). Penelitian ini menggunakan metode AMT untuk mendapatkan gambaran bawah permukaan dengan pemodelan 1D dan pemodelan 2D. Pengolahan data dilakukan dengan menggunakan <em>software</em> MT Editor, Interpex, dan Petrel. <em>Geoelectrical</em> <em>strike</em> digunakan untuk mengetahui arah <em>strike</em> bawah permukaan dimana nilai kontras resistivitasnya dapat diindikasikan sebagai gangguan geologi. Data yang digunakan adalah data <em>angle</em> dan <em>radius</em> pada <em>software</em> MT Editor. Sementara <em>software</em> yang digunakan untuk membuat diagram roset adalah <em>software</em> GeoRose. Hasil pemodelan menunjukkan adanya komponen panasbumi berupa <em>claycap </em>(1 Ω.m – 10 Ω.m) dan <em>reservoir </em>(10 Ω.m – 20 Ω.m) pada kedalaman 300 m hingga 2000 m. Lapisan <em>young sedimentary rock </em>diinterpretasikan sebagai zona aliran air panas dengan nilai tahanan jenis sebesar 10 Ω.m – 100 Ω.m. Sistem panasbumi di daerah penelitian diduga dikontrol oleh struktur geologi berupa sesar mendatar, antiklin, dan sinklin yang berkembang di bagian timurlaut daerah penelitian. </span></p><p><em style="font-size: medium;">T</em><em style="font-size: medium;">he areas that possibly had geothermal system is Mount Pancar, Bogor, West Java. There are several hot springs found around the study area. The geophysical method that can be used to identify the geothermal system and geological structure is the Audio-Magnetotelluric Method (AMT). AMT method is used to obtain subsurface overview with 1D modeling and 2D modeling. Data processing is done by using MT Editor, Interpex, and Petrel software. Geoelectrical strike is used to determine the direction of the subsurface strike by resistivity value. The most dominant angle and radius data from software MT Editor is used to make rosette diagram to show the geoelectrical strike. The results of 1D modeling showed the geothermal component such as claycap (1 Ω.m - 10 Ω.m) and reservoir (10 Ω.m - 20 Ω.m) at a depth of 300 m to 2000 m. The young sedimentary rock layer is interpreted as a discharge zone with a resistance value of 10 Ω.m - 100 Ω.m. The geothermal systems in the study area might be controlled by geological structures in the northeast of the study area.</em></p>


Author(s):  
Mochamad Iqbal ◽  
Bella Restu Juliarka ◽  
Wijayanti Ashuri ◽  
Bilal Al Farishi

Natar Hot Spring is one of the geothermal manifestations that is located in Lampung Province, Indonesia. About 6 km to the east, another hot spring appears with temperature around 40°C with neutral pH called Cisarua Hot Spring. The Natar Hot Spring itself having temperature 47-54°C with 6.23 pH. Based on the geologic map, the appearance of these hot spring is caused by Lampung-Panjang Fault which trending northwest-southeast. Morphology of the research area is showing a flat terrain topography which composed of Quaternary volcanic rock and metamorphic rock in the basement. The nearest volcano that expected to be the heat source of the geothermal system is the Quaternary extinct volcano called Mt. Betung which is located about 15 km to the southwest. The aim of the study is to analyze the geochemistry of the manifestations and calculate the reservoir temperature. Geochemistry analysis result shows both manifestations are bicarbonate which is formed as a steam-heated water or steam condensates. Geothermometer calculation shows that the geothermal reservoir has temperature 150-160°C with approximately 300 m in depth. All manifestations are originated from meteoric water according to stable isotope analysis D and δ18O data and interacting with carbonate-metamorphic rock beneath the surface based on 13C isotope value. A further geophysics study is needed to determine where the heat comes from.


2021 ◽  
Vol 9 ◽  
Author(s):  
Yanyan Li ◽  
Ji Dor ◽  
Chengjiang Zhang ◽  
Guiling Wang ◽  
Baojian Zhang ◽  
...  

The Xifeng geothermal field is located in the Yangtze Craton, SW China, and is one of the most representative low-temperature geothermal fields in China. Widespread thermal anomalies, hot springs, and geothermal wells have been reported by previous studies. However, the nature and forming mechanisms of the field remain poorly understood. Element geochemical (ions, rare earth elements) and stable isotopic (D, O) composition of hot springs, geothermal fluids, rivers, and cold springs from different locations of the Xifeng geothermal field were analyzed in this study. The ions studies revealed that most samples featured the Ca-Mg-HCO3 type, except Xifeng hot springs, and which were characterized by the Ca-Mg-HCO3-SO4 type. Based on quartz geothermometers, the estimated reservoir temperature was 77°C. The results of stable isotopes (D, O) manifest that the Xifeng geothermal system was recharged by meteoric water at an elevation of 1,583 m from SW to NE. The research of rare earth elements (REE) revealed that their accumulation characteristics and obvious positive Eu anomaly were inherited from host feldspar-bearing reservoir dolomites through water-rock interactions. Combined with these observations, geological setting, and previous studies, it was concluded that the formation of the Xifeng geothermal field resulted from recharge, deep circulation, and secondary rising of the meteoric water along the faults. First, meteoric water infiltrated to depth through faults and crack zones. Second, the deep-infiltrated water was heated by radioactive heat, deep heat, and tectonic frictional heat. Finally, as the warmed-up waters underwent considerable deep circulation in the reservoir, it rose again along the main faults, and mixed with groundwater near the surface. Taken together, we suggest that the Xifeng geothermal system should be assigned as a faults-controlling, and deeply circulating meteoric water of low-temperature category.


Geophysics ◽  
2013 ◽  
Vol 78 (3) ◽  
pp. B121-B130 ◽  
Author(s):  
Jared R. Peacock ◽  
Stephan Thiel ◽  
Graham S. Heinson ◽  
Peter Reid

Realization of enhanced geothermal systems (EGSs) prescribes the need for novel methods to monitor subsurface fracture connectivity and fluid distribution. Magnetotellurics (MT) is a passive electromagnetic (EM) method sensitive to electrical conductivity contrasts as a function of depth, specifically hot saline fluids in a resistive porous media. In July 2011, an EGS fluid injection at 3.6-km depth near Paralana, South Australia, was monitored by comparing repeated MT surveys before and after hydraulic stimulation. An observable coherent change above measurement error in the MT response was present and causal, in that variations in phase predict variations in apparent resistivity. Phase tensor residuals proved the most useful representation for characterizing alterations in subsurface resistivity structure, whereas resistivity tensor residuals aided in determining the sign and amplitude of resistivity variations. These two tensor representations of the residual MT response suggested fluids migrated toward the northeast of the injection well along an existing fault system trending north-northeast. Forward modeling and concurrent microseismic data support these results, although microseismic data suggest fractures opened along two existing fracture networks trending north-northeast and northeast. This exemplifies the need to use EM methods for monitoring fluid injections due to their sensitivity to conductivity contrasts.


Author(s):  
Jordi Andrifa ◽  
Nana Sulaksana ◽  
Dewi Gentana ◽  
Murni Sulastri

The study area is located in Gunung Talang District and its surroundings, Solok Regency, West Sumatra Province, Indonesia. This area has a potential volcanic geothermal system and is generally covered by the Quarternary rocks which are deformed due to the tectonic activity of the Sumatran Fault System. Geological structure traces are not well preserved in such an area. This study aims to determine the geological lineament pattern associated with geological structure, the geomorphic indices characteristic related to the tectonic activity and rock permeability, and the geothermal manifestation appearance based on these two factors. Geological lineament pattern is identified using the remote sensing method. Geomorphic indices characteristic is calculated through the quantitative analysis of bifurcation ratio (Rb), drainage density (Dd), mountain front sinuosity (Smf), and lineament density (Ld). Geothermal manifestation appearance is evaluated through geospatial analysis using the overlay method on the geological lineament pattern and the geomorphic indices characteristic, which are then correlated with the distribution of geothermal manifestations. The main geological lineament patterns associated with the geological structures in the study area are north-northwest–south-southeast (NNW-SSE) and northeast-southwest (NE-SW). These lineament patterns indicate synthetic and antithetic strike-slip faults around the Sumani Segment of Sumatran Fault System successively. The geomorphic indices characteristics imply deformed areas (Rb values: 1.14-5.45), rough (Dd values: 2.00-2.66 km/km2), moderate (Dd values: 3.14-4.00 km/km2), and slightly fine landform textures (Dd values: 4.32-5.51 km/km2), active (Smf values: 1.05-1.64) and moderate to slightly active tectonisms (Smf values: 1.74-2.52), low (Ld values: 0.00-0.84 km-1), moderate (Ld values: 0.84-1.68 km-1), and high lineament densities (Ld values: 1.68-2.52 km-1) over the study area. The geothermal manifestations in the study area are divided into four groups based on their appearance characteristics, namely group I (Songsang and Garara hot springs), group II (Padang Damar, Bukit Gadang, and Batu Bajanjang hot springs), group III (Bukit Kili and Bawah Gunuang hot springs), and group IV (Gabuo Atas and Bawah Betung hot springs).


2020 ◽  
Author(s):  
Domenico Liotta ◽  
Alessandro Agostini ◽  
Eivind Bastesen ◽  
Caterina Bianco ◽  
Chiara Boschi ◽  
...  

&lt;p&gt;The investigation of the deep geothermal systems is a challenging task in active geothermal systems. In order to decrease the mining risk, the study of the analogue exhumed systems sheds light on the relationships between fluid circulation and geological structures through the analyses of faults and ore deposits distributions. In the Las Minas area (Central Mexico), ore deposits are quite diffuse at the boundary between crystalline and sedimentary rocks and in fault zones. This is a consequence of the interaction between cooling of Miocene felsic magmas, hydrothermal fluids and coeval fault activity. We investigated the role of the faults in channeling the hydrothermal fluids by fieldwork and analysis of fractures at outcrops. The field mapping was carried out at 1:10000 scale (60 km2). When possible, kinematic data on recent fault planes influencing the permeability and geothermal fluid paths were collected. This includes information on the main structural trends and the orientation of the intermediate kinematic axis.The evolution and origin of the hydrothermal fluids circulating in the exhumed geothermal system of Las Minas area (Central Mexico) were investigated by i) structural and minero-petrographic studies and, ii) fluid inclusion and isotope analyses carried out on skarn and hydrothermal alteration minerals.Two families of faults have been recognized, NNW-SSE and SW-NE oriented, respectively. The SW-NE trending faults often controlled the emplacement of dykes, indicating that the magmatic fluid was channeled and driven by the faults induced permeability. Their activity is at least encompassed between Miocene and Quaternary. The kinematic relation between these two fault systems could be explained in a extensional framework, assuming that the NNW-SSE fault system acted as transfer faults. Fluid inclusions recorded the circulation of: 1) high-temperature (up to 650&amp;#176;C), high-salinity (up to 60 wt.% NaCl equiv.) fluid of magmatic origin; 2) high-temperature (470-650&amp;#176;C) aqueous-carbonic fluid produced during fluid-rock interaction with carbonate basement rocks and 3) relatively low-salinity (up to 2 wt.% NaCl equiv.) fluid of meteoric origin. A general evolution from high- to low-temperature fluid circulation characterized the geothermal system.&lt;/p&gt;


2021 ◽  
Vol 5 (2) ◽  
pp. 539-543
Author(s):  
Reza Firdaus ◽  
Siska Oktaviyani ◽  
Putri Hardianti ◽  
Tri Kusmita ◽  
Anisa Indriawati

Abstract   Geothermal manifestations on Bangka Island are found in the villages of Terak, Pemali, Sungailiat/Pelawan, Dendang, Permis, and Nyelanding. The manifestation of hot water in Terak Village, Central Bangka Regency is in the form of 3 hot springs with a surface temperature of 55ᵒC this research is to be carried focus on the structure of the subsurface rock layers using the geophysical method, namely the gravity method. The data used are topography and Free Air Anomaly. The data processing is in the form of Bouguer Correction and Terrain Correction to obtain the Complete Bouguer Anomaly (CBA) value. Then the CBA value is separated from regional anomalies and residual anomalies using the upward continuation method, as well as 2D modeling interpretation (forward modeling). From the research results, it is known that the subsurface rock structure of the non-volcanic geothermal system in Terak Village in the form of sandstone (2.28 – 2.49 gr/cm3) at a depth of 0 – 1.44 km is estimated as caprock, granite (2.77 – 2.78 gr/cm3) at a depth of 0 – 1.8 km is estimated as reservoir rock, and diorite rock (2.87 – 2.99 gr/ cm3) at a depth of 0 – 2 km is estimated as basement rock.    


2019 ◽  
Vol 125 ◽  
pp. 14002
Author(s):  
Rakhmadi Sulistyanto ◽  
Udi Harmoko ◽  
Gatot Yuliyanto

Research conducted at Pesanggrahan area, Sangubanyu Village, Bawang District, Batang Regency with geographical coordinates at 7°5'00 "00 S - 7°7'30" 00 S, and 109 ° 56'00 "E-109°58'30"E, with an area of around 25 Km². Research methods used quantitative and qualitative methods with descriptive analysis, geological and geochemical analysis. Geochemical fluid samples were taken in manifestations hot springs Pesanggrahan and hot water samples in Sibanteng and Sileri Crater to determine the relationship with geothermal systems in this area. Geomorphology divided into two geomorphology units, they are steep slope and sloping hill. Stratigraphy can be divided into three lithologies, which are andesite breccia, tuff breccia, and tuff sandstone. Based on fluid geochemical characteristics of manifestations, it can be interpreted that hot spring of Pesanggrahan area is outflow zone with bicarbonate-chloride water type, Sibanteng Crater and Sileri Crater, include upflow zone with water type sulfate for Sibanteng Crater, bicarbonate-sulfide water type for Sileri Crater. Environmental source geothermal fluid Pesanggrahan from the magmatic volcanic process. Sources geothermal fluid in Pesanggrahan, Sibanteng and Sileri Crater from meteoric water. Estimated temperature Pesanggrahan in the interval 50-100°C, Sileri Craters 160-180°C, and Sibanteng Craters 140-150°C. The Conceptual model of Pesanggrahan includes a geothermal system that associated with volcanic system and high relief liquid dominated system.


Water ◽  
2021 ◽  
Vol 13 (11) ◽  
pp. 1499
Author(s):  
Davide Fronzi ◽  
Francesco Mirabella ◽  
Carlo Cardellini ◽  
Stefano Caliro ◽  
Stefano Palpacelli ◽  
...  

The interaction between fluids and tectonic structures such as fault systems is a much-discussed issue. Many scientific works are aimed at understanding what the role of fault systems in the displacement of deep fluids is, by investigating the interaction between the upper mantle, the lower crustal portion and the upraising of gasses carried by liquids. Many other scientific works try to explore the interaction between the recharge processes, i.e., precipitation, and the fault zones, aiming to recognize the function of the abovementioned structures and their capability to direct groundwater flow towards preferential drainage areas. Understanding the role of faults in the recharge processes of punctual and linear springs, meant as gaining streams, is a key point in hydrogeology, as it is known that faults can act either as flow barriers or as preferential flow paths. In this work an investigation of a fault system located in the Nera River catchment (Italy), based on geo-structural investigations, tracer tests, geochemical and isotopic recharge modelling, allows to identify the role of the normal fault system before and after the 2016–2017 central Italy seismic sequence (Mmax = 6.5). The outcome was achieved by an integrated approach consisting of a structural geology field work, combined with GIS-based analysis, and of a hydrogeological investigation based on artificial tracer tests and geochemical and isotopic analyses.


Energies ◽  
2020 ◽  
Vol 13 (10) ◽  
pp. 2473
Author(s):  
Yujiang He ◽  
Xianbiao Bu

The energy reserves in hot dry rock and hydrothermal systems are abundant in China, however, the developed resources are far below the potential estimates due to immature technology of enhanced geothermal system (EGS) and scattered resources of hydrothermal systems. To circumvent these problems and reduce the thermal resistance of rocks, here a shallow depth enhanced geothermal system (SDEGS) is proposed, which can be implemented by fracturing the hydrothermal system. We find that, the service life for SDEGS is 14 years with heat output of 4521.1 kW. To extend service life, the hybrid SDEGS and solar energy heating system is proposed with 10,000 m2 solar collectors installed to store heat into geothermal reservoir. The service life of the hybrid heating system is 35 years with geothermal heat output of 4653.78 kW. The novelty of the present work is that the hybrid heating system can solve the unstable and discontinuous problems of solar energy without building additional back-up sources or seasonal storage equipment, and the geothermal thermal output can be adjusted easily to meet the demand of building thermal loads varying with outside temperature.


Sign in / Sign up

Export Citation Format

Share Document