scholarly journals Mechanical state of gravel soil in mobilization of rainfall-induced landslides in the Wenchuan seismic area, Sichuan province, China

2018 ◽  
Vol 6 (3) ◽  
pp. 637-649
Author(s):  
Liping Liao ◽  
Yunchuan Yang ◽  
Zhiquan Yang ◽  
Yingyan Zhu ◽  
Jin Hu ◽  
...  
Keyword(s):  
Critical State ◽  
Void Ratio ◽  
Fine Particles ◽  
Pore Water Pressure ◽  
Water Pressure ◽  
State Parameter ◽  
Confining Pressure ◽  
Dry Density ◽  
Mechanical State ◽  
Gravel Soil

Abstract. Gravel soils generated by the Wenchuan earthquake have undergone natural consolidation for the past decade. However, geological hazards, such as slope failures with ensuing landslides, have continued to pose great threats to the region. In this paper, artificial model tests were used to observe the changes of soil moisture content and pore water pressure, as well as macroscopic and microscopic phenomena of gravel soil. In addition, a mathematical formula of the critical state was derived from the triaxial test data. Finally, the mechanical states of gravel soil were determined. The results had five aspects. (1) The time and mode of the occurrence of landslides were closely related to the initial dry density. The process of initiation was accompanied by changes in density and void ratio. (2) The migration of fine particles and the rearrangement of coarse–fine particles contributed to the reorganization of the microscopic structure, which might be the main reason for the variation of dry density and void ratio. (3) If the confining pressure were the same, the void ratios of soils with constant particle composition would approach approximately critical values. (4) Mechanical state of gravel soil can be determined by the relative position between state parameter (e, p′) and ec–p′ planar critical state line, where e is the void ratio, ec is the critical void ratio and p′ is the mean effective stress. (5) In the process of landslide initiation, dilatation and contraction were two types of gravel soil state, but dilatation was dominant. This paper provided insight into interpreting landslide initiation from the perspective of critical state soil mechanics.

scholarly journals Mechanical State of Gravel Soil in Mobilization of Rainfall-Induced Landslide in Wenchuan seismic area, Sichuan province, China

2018 ◽  
Author(s):  
Liping Liao ◽  
Yunchuan Yang ◽  
Zhiquan Yang ◽  
Yingyan Zhu ◽  
Jin Hu ◽  
...  
Keyword(s):  
Fine Particle ◽  
Void Ratio ◽  
State Parameter ◽  
Particle Migration ◽  
Triaxial Tests ◽  
Dry Density ◽  
Mechanical State ◽  
Consolidation Process ◽  
Gravel Soil ◽  
Seismic Area

Abstract. Although gravel soils generated by seismic shaking in Wenchuan earthquake area have subjected to natural consolidation process for nearly ten years, geological hazards, such as slope failures with ensuing landslides, frequently are haunting the area. In this paper, artificial flume model tests and triaxial tests were used to make close observation on the mechanical state of gravel soil in Wenchuan seismic area. The results showed that: (1) The timing and patterns of landslide initiations were closely related to their initial dry densities, and the initiation processes were accompanied with a variation of dry density and void ratio; (2) Fine particle migration in soil and coarse-fine particle content rearrangement contributed to the internal micro structure reorganization, which was supposed to be the main reason for variation of dry density and void ratio; (3) Gravel soils with unchanged grain compositions, if under the same hydrostatic compression, they approached to an identical critical void ratio to fail; (4) The mechanical state of certain sort of gravel soil can be identified by its relative position between state parameter (e, p') and ec-p' planar critical state line; (5) Gravel soil slope failed and then evolved into landslide under lasting rainfall leaching, while in gravel slope there co-existed soil dilatation and contraction, but the dilatation was dominant. Above research findings not only could be used to interpret landslide initiation but also would provide an insight for landslide warning forecast of gravel slope in seismic area.

scholarly journals Effect of Variable Confining Pressure on Cyclic Triaxial Behavior of K0-consolidated Soft Marine Clay

2018 ◽  
Vol 4 (4) ◽  
pp. 755
Author(s):  
Lei Sun
Keyword(s):  
Pore Water ◽  
Pore Water Pressure ◽  
Axial Strain ◽  
Water Pressure ◽  
Confining Pressure ◽  
Stress Path ◽  
Cyclic Stress ◽  
Marine Clay ◽  
Stress Ratios ◽  
Variable Confining Pressure

The effect of variable confining pressure (VCP) on the cyclic deformation and cyclic pore water pressure in K0-consolidated saturated soft marine clay were investigated with the help of the cyclic stress-controlled advanced dynamic triaxial test in undrained condition. The testing program encompassed three cyclic deviator stress ratios, CSR=0.189, 0.284 and 0.379 and three stress path inclinations ηampl=3,1 and 0.64. All tests with constant confining pressure (CCP) and variable confining pressure (VCP) have identical initial stress and average stress. The results were analyzed in terms of the accumulative normalized excess pore water pressure rqu recorded at the end of each stress cycle and permanent axial strain, as well as resilient modulus. Limited data suggest that these behavior are significantly affected by both of the VCP and CSR. For a given value of VCP, both of the pore water pressure rqu and permanent axial strains are consistently increase with the increasing values of CSR. However, for a given value of CSR, the extent of the influence of VCP and the trend is substantially depend on the CSR.

scholarly journals Experimental Study on the Variation Law of Excess Pore Water Pressure at the Bottom of the Foundation Pit for Excavation

2020 ◽  
Vol 2020 ◽  
pp. 1-11
Author(s):  
Qizhi Hu ◽  
Qiang Zou ◽  
Zhigang Ding ◽  
Zhaodong Xu
Keyword(s):  
Pore Water ◽  
Pore Water Pressure ◽  
Water Pressure ◽  
Soft Soil ◽  
Confining Pressure ◽  
Deep Foundation ◽  
Foundation Pit ◽  
Excess Pore Water Pressure ◽  
Accurate Expression ◽  
Excess Pore

The excavation unloading of deep foundation pits in soft soil areas often produces negative excess pore water pressure. The rebound deformation of soil on the excavation surface of the foundation pit can be predicted reliably through the accurate expression of relevant variation laws. In combination with the principle of effective stress and the general equation of unidirectional seepage consolidation, an equation for calculating the rebound deformation from the bottom in the process of foundation pit excavation unloading was obtained. Additionally, a triaxial unloading test was adopted to simulate the excavation unloading processes for actual foundation pit engineering. After studying the variation law of the excess pore water pressure generated by excavation unloading, it was found that the negative excess pore water pressure increased with increasing unloading rate, while the corresponding peak value decreased with increasing confining pressure. The equation for rebound calculation was verified through a comparison with relevant measured data from actual engineering. Therefore, it is considered that the equation can reliably describe the rebound deformation law of the base. This paper aims to guide the design and construction of deep foundation pits in soft soil areas.

Studying the Geotechnical Properties of Clayey Soil Contaminated by Kerosene

2020 ◽  
Vol 857 ◽  
pp. 383-393
Author(s):  
Mahdi O. Karkush ◽  
Amer G. Jihad
Keyword(s):  
Shear Strength ◽  
Water Content ◽  
Contaminated Soil ◽  
Fine Particles ◽  
Clayey Soil ◽  
Pore Water Pressure ◽  
Water Pressure ◽  
Chemical Characteristics ◽  
Coefficient Of Consolidation ◽  
Plastic Containers

This study focuses on investigating the impacts of kerosene on the physical, mechanical, and chemical characteristics of clay soil. The soils specimens are contaminated artificially with six ratios of kerosene (5, 10, 20, 30, 40, and 50) % calculated according to the dry weight of soil. The artificial contamination includes air drying of the disturbed soil, then placed in plastic containers and mixed with the field water content and the specified concentration of kerosene to ensure getting homogenous contaminated soil specimens. The contaminated soil specimens left for 30 days in plastic containers covered by nylon sheets to control the water content and prevent volatility of contaminant. The results of tests proved that different ratios of kerosene have different impacts on the engineering and chemical characteristics of soil specimens. The specific gravity, percentages of fine particles, optimum water content, the initial and final void ratio, coefficient of consolidation, swelling index, permeability, the undrained shear strength, effective shear strength parameters, and the rate of reduction of initial pore water pressure are reduced significantly with increasing the content of kerosene in soil. Generally, the concentration of kerosene less than 10% has slight impacts on the studied characteristics of soil specimens.

Aspects of the behaviour of compacted clayey soils on drying and wetting paths

2002 ◽  
Vol 39 (6) ◽  
pp. 1341-1357 ◽  
Author(s):  
Jean-Marie Fleureau ◽  
Jean-Claude Verbrugge ◽  
Pedro J Huergo ◽  
António Gomes Correia ◽  
Siba Kheirbek-Saoud
Keyword(s):  
Water Content ◽  
Pore Water ◽  
Unsaturated Soils ◽  
Pore Water Pressure ◽  
Water Pressure ◽  
Dry Density ◽  
Clayey Soils ◽  
Maximum Dry Density ◽  
Optimum Water Content ◽  
Optimum Water

A relatively large number of drying and wetting tests have been performed on clayey soils compacted at the standard or modified Proctor optimum water content and maximum density and compared with tests on normally consolidated or overconsolidated soils. The results show that drying and wetting paths on compacted soils are fairly linear and reversible in the void ratio or water content versus negative pore-water pressure planes. On the wet side of the optimum, the wetting paths are independent of the compaction water content and can be approached by compaction tests with measurement of the negative pore-water pressure. Correlations have been established between the liquid limit of the soils and such properties as the optimum water content and negative pore-water pressure, the maximum dry density, and the swelling or drying index. Although based on a limited number of tests, these correlations provide a fairly good basis to model the drying–wetting paths when all the necessary data are not available.Key words: compaction, unsaturated soils, clays, drying, wetting, Proctor conditions.

Modified state parameter for characterizing static liquefaction of sand with fines

2009 ◽  
Vol 46 (3) ◽  
pp. 281-295 ◽  
Author(s):  
D. C. Bobei ◽  
S. R. Lo ◽  
D. Wanatowski ◽  
C. T. Gnanendran ◽  
M. M. Rahman
Keyword(s):  
Critical State ◽  
Volumetric Strain ◽  
State Parameter ◽  
Confining Pressure ◽  
Log P ◽  
Test Results ◽  
Static Liquefaction ◽  
Isotropic Consolidation ◽  
Failure Line ◽  
Soil Behaviour

An experimental study was carried out to investigate the static liquefaction behaviour of sand with a small amount of plastic and nonplastic fines. Five series of tests were conducted in drained and undrained conditions. The drained test results indicate not only that the failure line coincides with the critical state, but also that the development of volumetric strain during shearing was not sensitive to the initial confining pressure. In both isotropically and anisotropically consolidated undrained tests, a so-called “reverse behaviour” was consistently observed. The results were also interpreted in the critical state framework. The critical and steady state (CS/SS) data were found to trace along the same curve in e–log( p′) space, irrespective of the stress history and effective stress paths. A comparison between the isotropic consolidation line (ICL) and critical state (CS) curve showed that a small amount of fines can significantly change the shape and position of the ICL relative to the CS curve. Furthermore, the soil behaviour manifested in both drained and undrained shearing led to the development of a modified state parameter.

scholarly journals Swelling phenomena and effective stress in compacted expansive clays

2016 ◽  
Vol 53 (1) ◽  
pp. 134-147 ◽  
Author(s):  
David Mašín ◽  
Nasser Khalili
Keyword(s):  
Pore Water ◽  
Effective Stress ◽  
Pore Water Pressure ◽  
Water Pressure ◽  
Swelling Pressure ◽  
Constitutive Modelling ◽  
Dry Density ◽  
Expansive Clay ◽  
Experimental Database ◽  
Clay Aggregates

The central aim of this paper is to discuss the applicability of the effective stress principle as defined by Terzaghi (total stress minus pore-water pressure) to predict the behaviour of expansive clay aggregates. Phenomena occurring between individual clay minerals are reviewed first at the molecular level obtained in the colloid science research. In particular, it is noted that, for interparticle distances higher than approximately 1.5 nm, the pore-water pressure in the bulk equilibrium solution forms an additive component of the interparticle disjoining pressure. It is concluded that for these distances Terzaghi’s effective stress principle should be adequate to describe the clay behaviour. To support these developments, an extensive experimental database of nine different sodium and calcium bentonites available in the published literature was analysed. With the aid of double structure constitutive modelling, procedures were developed to extract information about the behaviour of clay aggregates from the experimental measurements. It was then shown that unconfined water retention curves, swelling pressure tests, swelling under constant load tests, and mechanical unloading tests are all uniquely related in terms of the dependency of dry density (or void ratio) of clay aggregate versus mean effective stress. By considering reversibility of aggregate behaviour and full saturation of aggregates, this implies that the effective stress principle is a valid way of predicting expansive clay aggregate volumetric deformation.

Theoretical prediction of rutting in flexible pavement subgrades

1992 ◽  
Vol 29 (5) ◽  
pp. 765-778 ◽  
Author(s):  
D. V. Ramsamooj ◽  
R. Piper
Keyword(s):  
Pore Water ◽  
Critical State ◽  
Pore Water Pressure ◽  
Water Pressure ◽  
Permanent Deformation ◽  
Flexible Pavement ◽  
Load Test ◽  
Model Parameters ◽  
Silty Clay ◽  
Rate Of Development

The theoretical model for predicting the cyclic response of soils is extended to handle the generation and dissipation of pore-water pressures and to predict the rutting of the subgrade of a flexible pavement. The model utilizes multiyield surfaces and the concepts of critical state mechanics to predict the permanent deformation of the subgrade under vehicular loading. The theoretical solution also considers the effects of the drainage characteristics of the subgrade soil on the rate of development of the permanent deformation. Experimental verification of the model concepts are presented for a drained cyclic load test on Ottawa sand and for undrained cyclic loading on Newfield clay using published experimental data. An illustrative example is given for the prediction of rutting in a silty clay subgrade. The model parameters for the silty clay are obtained from triaxial and consolidation tests. These parameters are then put into a computer program that determines the rut depth, pore-water pressure, and the ratio of the vertical deformation and the rut depth as functions of the number of vehicular loads for a flexible pavement for various conditions of drainage ranging from undrained to fully drained. The role of the coefficient of consolidation of the subgrade in controlling the rate of development of the rut depth is highlighted. Key words : critical state soil mechanics, multiyield surfaces, rutting, silty clay subgrade, drainage, vehicular loading.

scholarly journals The Undrained Characteristics of Tengger Desert Sand from True Triaxial Testing

2021 ◽  
Vol 2021 ◽  
pp. 1-10
Author(s):  
Xuefeng Li ◽  
Weinan Lu ◽  
Zhigang Ma ◽  
Ni Tuo
Keyword(s):  
Critical State ◽  
State Transition ◽  
Water Pressure ◽  
Confining Pressure ◽  
The State ◽  
Transition Line ◽  
Aeolian Sand ◽  
True Triaxial ◽  
Dense Sand ◽  
High Confining Pressure

Aimed at the characteristics of aeolian sand under rapid construction conditions in desert geotechnical engineering, a series of the true triaxial undrained test were carried out on the GDS apparatus. The 3D deformation, failure, and other characteristics of the dense sand are obtained. Under the condition of same p c , the state transition point where the void water pressure changes from increasing to decreasing appears earlier and leads to enhanced dilatancy with the increase of b, which means the enhanced dilatancy of dense sand caused the increase in strength. The results of the same b shows that the void water pressure generally indicates a decrease at low confining pressure and an increase at high confining pressure, indicating that the aeolian sand shows dilatancy at low confining pressure and contraction at high confining pressure. The state transition point increases with the increase of p c , but all points tend to the same critical state line and state transition line. When b = 0, the critical state line is q = 1.57 p ′ , and the state transition line is q = 1.23 p ′ . When b = 1, the critical state line is q = 1.24 p ′ , and the state transition line is q = 1.04 p ′ . The results at same b obtained the unified critical state line and the state transition line. Therefore, the true triaxial test can obtain the unified relationship of void ratio, p c and b, which overcomes the fact that the existing test cannot consider the influence of b. The test results provide a basis data for the design, construction, and maintenance of geotechnical engineering in Tengger Desert.

Effect of a vacuum gradient on the consolidation of dredged slurry by vacuum preloading

2020 ◽  
Author(s):  
Jun Wang ◽  
Yuanqiang Cai ◽  
Feiyu Liu ◽  
Zhe Li ◽  
Guohui Yuan ◽  
...  
Keyword(s):  
Large Scale ◽  
Fine Particles ◽  
Pore Water Pressure ◽  
Water Pressure ◽  
Soil Surface ◽  
Particle Analysis ◽  
Soil Consolidation ◽  
Vacuum Preloading ◽  
Consolidation Rate ◽  
Consolidation Degree

In this paper, a large-scale indoor model test was carried out to reinforce the dredged slurry by vacuum preloading, and the effect of the vacuum gradient on the reinforcement effect was studied. The vacuum pressure, volume of extracted water, average ground settlement and pore water pressure were monitored during the test. After the test, the water content and vane shear strength were measured, and a particle analysis test and a scanning electron microscopy test were carried out. The results indicated that a small vacuum gradient could improve the consolidation degree and strength of the soil, and the smaller the vacuum gradient is, the better the reinforcement of the soil is. In addition, reducing the vacuum gradient could decrease the differential settlement of the soil surface and alleviate the migration of fine particles to the prefabricated drainage plates; therefore, the small vacuum gradient improved the clogging of the prefabricated drainage plates and the uniformity of soil consolidation. However, reducing the vacuum gradient also extended the test period, and a vacuum gradient of 20 kPa obtained the fastest consolidation rate of the soil.

Sign in / Sign up

Export Citation Format

Share Document