scholarly journals Characterization of stony soils' hydraulic conductivity using laboratory and numerical experiments

SOIL ◽  
2016 ◽  
Vol 2 (3) ◽  
pp. 421-431 ◽  
Author(s):  
Eléonore Beckers ◽  
Mathieu Pichault ◽  
Wanwisa Pansak ◽  
Aurore Degré ◽  
Sarah Garré
Keyword(s):  
Hydraulic Conductivity ◽  
Water Flow ◽  
Predictive Models ◽  
Laboratory Experiments ◽  
Saturated Hydraulic Conductivity ◽  
Experimental Conditions ◽  
Rock Fragments ◽  
Unsaturated Hydraulic Conductivity ◽  
The One ◽  
The Impact

Abstract. Determining soil hydraulic properties is of major concern in various fields of study. Although stony soils are widespread across the globe, most studies deal with gravel-free soils, so that the literature describing the impact of stones on the hydraulic conductivity of a soil is still rather scarce. Most frequently, models characterizing the saturated hydraulic conductivity of stony soils assume that the only effect of rock fragments is to reduce the volume available for water flow, and therefore they predict a decrease in hydraulic conductivity with an increasing stoniness. The objective of this study is to assess the effect of rock fragments on the saturated and unsaturated hydraulic conductivity. This was done by means of laboratory experiments and numerical simulations involving different amounts and types of coarse fragments. We compared our results with values predicted by the aforementioned predictive models. Our study suggests that it might be ill-founded to consider that stones only reduce the volume available for water flow. We pointed out several factors of the saturated hydraulic conductivity of stony soils that are not considered by these models. On the one hand, the shape and the size of inclusions may substantially affect the hydraulic conductivity. On the other hand, laboratory experiments show that an increasing stone content can counteract and even overcome the effect of a reduced volume in some cases: we observed an increase in saturated hydraulic conductivity with volume of inclusions. These differences are mainly important near to saturation. However, comparison of results from predictive models and our experiments in unsaturated conditions shows that models and data agree on a decrease in hydraulic conductivity with stone content, even though the experimental conditions did not allow testing for stone contents higher than 20 %.

scholarly journals Characterization of stony soils' hydraulic conductivity using laboratory and numerical experiments

2015 ◽  
Vol 2 (2) ◽  
pp. 1103-1133
Author(s):  
M. Pichault ◽  
E. Beckers ◽  
A. Degré ◽  
S. Garré
Keyword(s):  
Hydraulic Conductivity ◽  
Water Flow ◽  
Numerical Experiments ◽  
Saturated Hydraulic Conductivity ◽  
Rock Fragments ◽  
Hydraulic Behaviour ◽  
Unsaturated Hydraulic Conductivity ◽  
The One ◽  
The Impact

Abstract. Determining soil hydraulic properties is of major concern in various fields of study. Though stony soils are widespread across the globe, most studies deal with gravel-free soils so that the literature describing the impact of stones on soil's hydraulic conductivity is still rather scarce. Most frequently, models characterizing the saturated hydraulic conductivity of stony soils assume that the only effect of rock fragments is to reduce the volume available for water flow and therefore they predict a decrease in hydraulic conductivity with an increasing stoniness. The objective of this study is to assess the effect of rock fragments on the saturated and unsaturated hydraulic conductivity. This was done by means of laboratory and numerical experiments involving different amounts and types of coarse fragments. We compared our results with values predicted by the aforementioned models. Our study suggests that considering that stones only reduce the volume available for water flow might be ill-founded. We pointed out several drivers of the saturated hydraulic conductivity of stony soils, not considered by these models. On the one hand, the shape and the size of inclusions may substantially affect the hydraulic conductivity. On the other hand, the presence of rock fragments can counteract and even overcome the effect of a reduced volume in some cases. We attribute this to the creation of voids at the fine earth-stone interface. Nevertheless, these differences are mainly important near to saturation. However, we come up with a more nuanced view regarding the validity of the models under unsaturated conditions. Indeed, under unsaturated conditions, the models seem to represent the hydraulic behaviour of stones reasonably well.

scholarly journals Interpretation of ponded infiltration data using numerical experiments

2016 ◽  
Vol 64 (3) ◽  
pp. 289-299 ◽  
Author(s):  
Michal Dohnal ◽  
Tomas Vogel ◽  
Jaromir Dusek ◽  
Jana Votrubova ◽  
Miroslav Tesar
Keyword(s):  
Hydraulic Conductivity ◽  
Saturated Hydraulic Conductivity ◽  
Experimental Conditions ◽  
Insertion Depth ◽  
Retention Capacity ◽  
Soil Layering ◽  
Soil Hydraulic ◽  
The Impact ◽  
Infiltration Experiment

AbstractPonded infiltration experiment is a simple test used for in-situ determination of soil hydraulic properties, particularly saturated hydraulic conductivity and sorptivity. It is known that infiltration process in natural soils is strongly affected by presence of macropores, soil layering, initial and experimental conditions etc. As a result, infiltration record encompasses a complex of mutually compensating effects that are difficult to separate from each other. Determination of sorptivity and saturated hydraulic conductivity from such infiltration data is complicated. In the present study we use numerical simulation to examine the impact of selected experimental conditions and soil profile properties on the ponded infiltration experiment results, specifically in terms of the hydraulic conductivity and sorptivity evaluation. The effect of following factors was considered: depth of ponding, ring insertion depth, initial soil water content, presence of preferential pathways, hydraulic conductivity anisotropy, soil layering, surface layer retention capacity and hydraulic conductivity, and presence of soil pipes or stones under the infiltration ring. Results were compared with a large database of infiltration curves measured at the experimental site Liz (Bohemian Forest, Czech Republic). Reasonably good agreement between simulated and observed infiltration curves was achieved by combining several of factors tested. Moreover, the ring insertion effect was recognized as one of the major causes of uncertainty in the determination of soil hydraulic parameters.

scholarly journals The impact of different tillage treatments on hydraulic conductivity of loamy soil

2012 ◽  
Vol 60 (5) ◽  
pp. 109-114 ◽  
Author(s):  
Ivana Kameníčková ◽  
L. Larišová ◽  
A. Stoklásková
Keyword(s):  
Hydraulic Conductivity ◽  
Conventional Tillage ◽  
Saturated Hydraulic Conductivity ◽  
Water Infiltration ◽  
Reduced Tillage ◽  
Loamy Soil ◽  
Double Ring ◽  
Unsaturated Hydraulic Conductivity ◽  
The Impact

Water infiltration into the soil profile, surface runoff and soil erosion in arable lands depend on the conditions of the top layer. The tillage treatment of the top layer plays a key role in changes of the hydro-physical properties, mainly saturated hydraulic conductivity Ks of the surface layer. The aim of this study was to asses the impact of different tillage treatments on hydraulic conductivity in the locality Bohaté Málkovice. Field experimental works in this area were performed in 2009 and were repeted in 2011 on Haplic Chernozem, medium heavy loamy soil. The experimental area was divided into two parts; top layer of these plots was cultivated by applying conventional and reduced tillage treatment. Both these plots were sown with spring barley (Hordeum vulgare). For the field measurement of water infiltration into the soil was used double-ring infiltrometer (2009, 2011) and Minidisk infiltrometer (2011). Near the point were the infiltration was measured, the soil samples were always collected for laboratory determination of basic physical properties of soil (bulk density, porosity, initial and saturated water content, aeration of the soil) and saturated hydraulic conductivity Ks. For laboratory determination of Ks was used permeameter with constant gradient.For evaluation of saturated hydraulic conductivity Ks using the double-ring infiltration method was used Philip’s three-parameter equation and for evaluation of unsaturated hydraulic conductivity K(h) using Minidisk infiltrometer was used Zang’s method. After two years of using repeatedly applied different tillage treatments was significantly influenced saturated hydraulic conductivity Ks. The Ks value increased approximately six times for reduced tillage and more than three times for conventional tillage. Laboratory determined average values of Ks were compared with the average estimates of Ks from infiltration tests. The results were burdened by a number of errors (compaction, preferential flow). These mean values were higher for conventional and reduced tillage. Unsaturated hydraulic conductivity K(−2cm) for reduced tillage was higher, for conventional tillage decreased approximately three times.

scholarly journals Predicting the impact of biochar on the saturated hydraulic conductivity of natural and engineered media

2021 ◽  
Vol 295 ◽  
pp. 113143
Author(s):  
Yudi Yan ◽  
Seyyed Ali Akbar Nakhli ◽  
Jing Jin ◽  
Godfrey Mills ◽  
Clinton S. Willson ◽  
...  
Keyword(s):  
Hydraulic Conductivity ◽  
Saturated Hydraulic Conductivity ◽  
The Impact

Unsaturated hydraulic conductivity in limestone dolines: Influence of vegetation and rock fragments

Geoderma ◽  
2008 ◽  
Vol 145 (3-4) ◽  
pp. 288-294 ◽  
Author(s):  
Xiao-Yan Li ◽  
Sergio Contreras ◽  
Albert Solé-Benet
Keyword(s):  
Hydraulic Conductivity ◽  
Rock Fragments ◽  
Unsaturated Hydraulic Conductivity

scholarly journals Design and construction of the barrier system for the Halton Landfill

2000 ◽  
Vol 37 (3) ◽  
pp. 662-675 ◽  
Author(s):  
R Kerry Rowe ◽  
Chris J Caers ◽  
Glenn Reynolds ◽  
Cliff Chan
Keyword(s):  
Hydraulic Conductivity ◽  
Impact Assessment ◽  
Concentration Profile ◽  
Organic Contaminants ◽  
Laboratory Experiments ◽  
Chloride Concentration ◽  
Design Concept ◽  
Good Prediction ◽  
Air Pocket ◽  
The Impact

Considerations related to the design of the Halton Landfill as a "hydraulic trap" are summarized together with the research that was conducted to support the design concept. The interrelationship between hydrogeology and the engineered design is examined. Laboratory experiments demonstrated that there can be diffusion away from a source, even with significant inward velocity. Existing theory was found to provide a good prediction of the observed concentration profile in these experiments. It is also shown that a pressurized air pocket below the clay effectively acts as a zero-flux boundary and hence, with respect to migration of chloride, could be conservatively neglected in the impact assessment. The results of the impact calculations predict only a small increase in chloride concentration in the receptor aquifer while there is negligible predicted impact due to organic contaminants. The landfill was designed and constructed with a granular "sub-liner contingency layer" (SLCL) beneath the compacted liner. The operation of this layer is discussed. Finally, the construction of the compacted clayey liner with a hydraulic conductivity of 1 × 10-8 cm/s is documented.Key words: landfill, hydraulic containment, liner, field case, construction.

Historical development of soil-water physics and solute transport in porous media

2007 ◽  
Vol 7 (1) ◽  
pp. 59-66 ◽  
Author(s):  
D.E. Rolston
Keyword(s):  
Porous Media ◽  
Hydraulic Conductivity ◽  
Solute Transport ◽  
Soil Water ◽  
20Th Century ◽  
Water Flow ◽  
Unsaturated Soils ◽  
Transport Processes ◽  
Transport In Porous Media ◽  
Unsaturated Hydraulic Conductivity

The science of soil-water physics and contaminant transport in porous media began a little more than a century ago. The first equation to quantify the flow of water is attributed to Darcy. The next major development for unsaturated media was made by Buckingham in 1907. Buckingham quantified the energy state of soil water based on the thermodynamic potential energy. Buckingham then introduced the concept of unsaturated hydraulic conductivity, a function of water content. The water flux as the product of the unsaturated hydraulic conductivity and the total potential gradient has become the accepted Buckingham-Darcy law. Two decades later, Richards applied the continuity equation to Buckingham's equation and obtained a general partial differential equation describing water flow in unsaturated soils. For combined water and solute transport, it had been recognized since the latter half of the 19th century that salts and water do not move uniformly. It wasn't until the middle of the 20th century that scientists began to understand the complex processes of diffusion, dispersion, and convection and to develop mathematical formulations for solute transport. Knowledge on water flow and solute transport processes has expanded greatly since the early part of the 20th century to the present.

Impact of an Exponential Profile of Saturated Hydraulic Conductivity within the ISBA LSM: Simulations over the Rhône Basin

2006 ◽  
Vol 7 (1) ◽  
pp. 61-80 ◽  
Author(s):  
B. Decharme ◽  
H. Douville ◽  
A. Boone ◽  
F. Habets ◽  
J. Noilhan
Keyword(s):  
High Resolution ◽  
Hydraulic Conductivity ◽  
Land Surface ◽  
Large Scale ◽  
Saturated Hydraulic Conductivity ◽  
Rooting Depth ◽  
Surface Model ◽  
Low Resolution ◽  
The Impact ◽  
Hydrological Applications

Abstract This study focuses on the influence of an exponential profile of saturated hydraulic conductivity, ksat, with soil depth on the water budget simulated by the Interaction Soil Biosphere Atmosphere (ISBA) land surface model over the French Rhône River basin. With this exponential profile, the saturated hydraulic conductivity at the surface increases by approximately a factor of 10, and its mean value increases in the root zone and decreases in the deeper region of the soil in comparison with the values given by Clapp and Hornberger. This new version of ISBA is compared to the original version in offline simulations using the Rhône-Aggregation high-resolution database. Low-resolution simulations, where all atmospheric data and surface parameters have been aggregated, are also performed to test the impact of the modified ksat profile at the typical scale of a climate model. The simulated discharges are compared to observations from a dense network consisting of 88 gauging stations. Results of the high-resolution experiments show that the exponential profile of ksat globally improves the simulated discharges and that the assumption of an increase in saturated hydraulic conductivity from the soil surface to a depth close to the rooting depth in comparison with values given by Clapp and Hornberger is reasonable. Results of the scaling experiments indicate that this parameterization is also suitable for large-scale hydrological applications. Nevertheless, low-resolution simulations with both model versions overestimate evapotranspiration (especially from the plant transpiration and the wet fraction of the canopy) to the detriment of total runoff, which emphasizes the need for implementing subgrid distribution of precipitation and land surface properties in large-scale hydrological applications.

scholarly journals Effects of oil field brine wastewater on saturated hydraulic conductivity of smectitic loam soils

2016 ◽  
Vol 96 (4) ◽  
pp. 496-503 ◽  
Author(s):  
Nathan E. Derby ◽  
Francis X.M. Casey ◽  
Thomas M. DeSutter
Keyword(s):  
Hydraulic Conductivity ◽  
Water Flow ◽  
Great Plains ◽  
Crop Production ◽  
Saturated Hydraulic Conductivity ◽  
Oil Field ◽  
Oil Well ◽  
High Sodium ◽  
Saturated Water ◽  
Western North Dakota

Spills of brine wastewater produced during oil well drilling are occurring more frequently in the Great Plains, resulting in crop production loss on affected soil. Remediation requires removal of salt from the topsoil, which might be accomplished by leaching to subsurface horizons or subsurface drains. A laboratory study determined the effects of brine on saturated hydraulic conductivity (Ks) of four nonimpacted surface soils from western North Dakota, USA. Repacked soil cores were subjected to saturated water flow, followed by one pore volume of brine. Subsequent saturated water flow leached brine from the soil and reduced Ks as much as 97% (0.086–0.003 cm h−1) within 24 h. Effluent total dissolved solids (TDS) approached 250 000 mg L−1 then declined (5 mg L−1) with continued leaching, but Ks did not increase. Removal of soluble salts during leaching increased the relative sodium concentrations (ESP > 55), causing clay swelling/dispersion and reduced Ks. Postbrine gypsum application (11.2 Mg ha−1) to replace exchangeable sodium with calcium did not improve Ks. This evidence suggests that if subsurface drainage is used for reclaiming brine-impacted soils that special attention be given to where dispersion/swelling is occurring, leaching water quality, and closely positioning calcium amendments within the high sodium zones.

scholarly journals Estimation of Unsaturated Hydraulic Conductivity of Granular Soils from Particle Size Parameters

Water ◽  
2019 ◽  
Vol 11 (9) ◽  
pp. 1826 ◽  
Author(s):  
Ji-Peng Wang ◽  
Pei-Zhi Zhuang ◽  
Ji-Yuan Luan ◽  
Tai-Heng Liu ◽  
Yi-Ran Tan ◽  
...  
Keyword(s):  
Grain Size ◽  
Hydraulic Conductivity ◽  
Water Retention ◽  
Intrinsic Value ◽  
Estimation Method ◽  
Sandy Soils ◽  
Saturated Hydraulic Conductivity ◽  
Water Retention Curve ◽  
Porosity Variation ◽  
Unsaturated Hydraulic Conductivity

Estimation of unsaturated hydraulic conductivity could benefit many engineering or research problems such as water flow in the vadose zone, unsaturated seepage and capillary barriers for underground waste isolation. The unsaturated hydraulic conductivity of a soil is related to its saturated hydraulic conductivity value as well as its water retention behaviour. By following the first author’s previous work, the saturated hydraulic conductivity and water retention curve (WRC) of sandy soils can be estimated from their basic gradation parameters. In this paper, we further suggest the applicable range of the estimation method is for soils with d10 > 0.02mm and Cu < 20, in which d10 is the grain diameter corresponding to 10% passing and Cu is the coefficient of uniformity (Cu=d60d10). The estimation method is also modified to consider the porosity variation effect. Then the proposed method is applied to predict unsaturated hydraulic conductivity properties of different sandy soils and also compared with laboratory and field test results. The comparison shows that the newly developed estimation method, which predicts the relative permeability of unsaturated sands from basic grain size parameters and porosity, generally has a fair agreement with measured data. It also indicates that the air-entry value is mainly relative to the mean grain size and porosity value change from the intrinsic value. The rate of permeability decline with suction is mainly associated with grain size polydispersity.

Sign in / Sign up

Export Citation Format

Share Document