Cutting forces during drilling and selected physical and mechanical properties of the finish coating based on epoxy resin

2020 ◽  
Vol 111 ◽  
pp. 106-115
Author(s):  
Barbara Białowąs ◽  
Karol Szymanowski
Keyword(s):  
Mechanical Properties ◽  
Epoxy Resin ◽  
Cutting Forces ◽  
Uv Light ◽  
Physical And Mechanical Properties ◽  
Cutting Resistance ◽  
Wood Processing ◽  
Axial Forces ◽  
Epoxy Resin Coating ◽  
Torque Values

Abstract: Cutting forces during drilling and selected physical and mechanical properties of the finish coating based on epoxy resin. Paper presents selected tests of epoxy resin coating applied to American walnut wood (Juglans nigra L.). The aim of the study was to assess the machinability of wood flooded with resin during drilling. The axial forces and torque values were adopted for the machinability criteria. The idea of the research was the thesis questioning the possibility of processing epoxy resin coatings with the application of tools and parameters used during wood processing. In addition, the influence of UV light on the obtained coating was examined and abrasion tests were carried out. It was found the resin changes its colour under the influence of UV radiation, but the change is imperceptible to an average observer. Epoxy resin is characterized by low abrasion resistance compared to commonly used paint and varnish coatings. Although solid resin is characterized by high cutting resistance while drilling, the force values do not exceed the commonly cut wood-based materials.

Physical and mechanical properties of triacetate fibre modified with ED-5 epoxy resin

1972 ◽  
Vol 3 (3) ◽  
pp. 303-305
Author(s):  
Z. Yu. Sakalauskas ◽  
Ya. K. Matskevichene ◽  
Yu. I. Baltakite ◽  
I. I. Zdanavichyus
Keyword(s):  
Mechanical Properties ◽  
Epoxy Resin ◽  
Physical And Mechanical Properties ◽  
Triacetate Fibre

scholarly journals KUALITAS PAPAN PARTIKEL BERDASARKAN KOMPOSISI SEKAM PADI DAN KAYU SENGON DENGAN VARIASI KADAR PEREKAT

2019 ◽  
Vol 7 (2) ◽  
Author(s):  
Dendi Prayoga ◽  
. Dirhamsyah ◽  
. Nurhaida
Keyword(s):  
Mechanical Properties ◽  
Moisture Content ◽  
Rice Husk ◽  
Raw Materials ◽  
Urea Formaldehyde ◽  
Physical And Mechanical Properties ◽  
Solid Content ◽  
Particle Board ◽  
Rice Husks ◽  
Wood Processing

This research aimed to examine the physical and mechanical properties of particle boards based on the composition of raw materials and adhesive content and know the treatment of the composition of raw materials and the best adhesive content and meet the standard JIS A 5908-2003. The research was conducted at Wood Workshop Laboratory, Wood Processing Laboratory Faculty of Forestry,Tanjungpura University and Laboratory of PT. Duta Pertiwi Nusantara Pontianak. The adhesive used is Urea Formaldehyde with 52% Solid Content. Comparison of the composition of rice husks and sengon varies namely rice husk 50%: sengon 50%, rice husk 60%: sengon 40% and rice husk 70%: sengon 30%  and variations in the levels of UF adhesives, namely 14% and 16%, with target density 0,7 gr/cm3. The particleboard was 30 cm x 30 cm x 1 cm Pressing at temperature 140oC for 8 minutes, with  pressure of 25 kg/cm2. The research results of the study of density and moisture content meet the standards JIS A 5908-2003. The best particle values of rice husk and sengon  with composition a ratio of  rice husk 50%: sengon 50% , 16% adhesive content  16%, with density value of  0,7072 gr/cm3, moisture content 9,1949 %, thick development 12,3210 %, water absorption 68,8270 %, MOE 12110,7273 kg/cm2, MOR 161,0025 kg/cm2, firmness sticky 1,9320 kg/cm2, screw holding strength 62,3124 kg.Keywords : adhesive, composition, particle board, rice husk, sengon

Thermo Mechanical behaviour of Phenol Novolac Resin and Unsaturated Polyester Toughened Epoxy using nano Bentonite and Silica Nanoparticles

2020 ◽  
Vol 1 (3) ◽  
pp. 77-83
Keyword(s):  
Mechanical Properties ◽  
Epoxy Resin ◽  
Silica Nanoparticles ◽  
Moisture Absorption ◽  
Unsaturated Polyester ◽  
Physical And Mechanical Properties ◽  
Bending Test ◽  
Mechanical And Thermal Properties ◽  
Novolac Epoxy ◽  
Industrial Needs

Phenol novolac epoxy resin is a polymer matter which its properties can be modified for industrial needs. In this research, nanocomposites of phenol novolac epoxy resin and unsaturated polyester are made nano Bentonite and silica nanoparticles as filler. For this purpose, effect of nanoparticles percent on nanocomposite formation is studied and their physical, mechanical and thermal properties are obtained. The presence of unsaturated polyester in this process forms a cross-link capable of improving the physical and mechanical properties of epoxy resin. Fracture behavior was determined by a SEM device. Moreover, TGA, DSC, impact tests and bending test were applied for data analysis. When process ability is growing, moisture absorption decreases. Fracture toughness was also evaluated in a stoichiometric network. Physical and mechanical properties improve significantly with increasing nanoparticles. The most important reason for using this nanocomposite is its high resistance to corrosion.

Effect of thermomechanical densification of pine wood (Pinus sylvestris L.) on cutting forces and roughness during milling

2021 ◽  
Vol 113 ◽  
pp. 36-42
Author(s):  
Barbara Białowąs ◽  
Karol Szymanowski
Keyword(s):  
Mechanical Properties ◽  
Surface Roughness ◽  
Statistical Analysis ◽  
Pinus Sylvestris ◽  
Cutting Forces ◽  
Physical And Mechanical Properties ◽  
Milling Process ◽  
Pine Wood ◽  
Roughness Index ◽  
Modified Wood

Effect of thermomechanical densification of pine wood (Pinus sylvestris L.) on cutting forces and roughness during milling. The paper presents the results of research concerning the assessment of machinability of pine wood thermomechanically compacted. The assessment was made on the basis of the cutting forces and surface roughness after the milling process. Selected properties of native and modified wood were examined. Based on the research, it was found that compacted wood is characterized by higher cutting forces during milling. The surface quality after milling was examined and the roughness index Ra values were determined. The research shows that the modified wood is characterized by a lower Ra value both along and across the grain. Statistical analysis showed that the modification had a statistically significant effect on the values of cutting forces and the physical and mechanical properties of the tested wood.

Influence of Portland Cement Addition in the Physical and Mechanical Properties of Epoxy Resin

2015 ◽  
Vol 1088 ◽  
pp. 411-414 ◽  
Author(s):  
Francisco Augusto Zago Marques ◽  
Carlos Eduardo G. da Silva ◽  
André Luis Christoforo ◽  
Francisco Antonio Rocco Lahr ◽  
Túlio Hallak Panzera ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
Composite Material ◽  
Portland Cement ◽  
Physical Properties ◽  
Epoxy Resin ◽  
Modulus Of Elasticity ◽  
Epoxy Matrix ◽  
Physical And Mechanical Properties ◽  
Response Variable

This research evaluated, with the of the analyses of variance (ANOVA), a composite material based on epoxy matrix phase reinforced with Portland cement (CP-II) particles (0%wt [100%wt of resin], 20%wt, 40%wt, 60%wt). The response-variable investigated were modulus of elasticity (E) and compressive strength (S), bulk density (ρB), apparent density (ρA) and porosity (P). The highest values of the modulus of elasticity were provided from the composites manufactured with 40wt% of cement addition. The inclusion of 60% of cement implies in a reduction in the mechanical properties when compared with the results of the composite manufactured with 40% of cement. For the physical properties, the gradually inclusion of cement provides increasing in the density of the composites, and reduce the porosity of the materials manufactured.

Resin-Wood Particulate Composite Reinforced with Piassava Fibre

2015 ◽  
Vol 1088 ◽  
pp. 415-418
Author(s):  
André Luis Christoforo ◽  
Francisco Antonio Rocco Lahr ◽  
Cristiane Inácio de Campos ◽  
Elen Aparecida Martines Morales ◽  
Juliana Cortez Barbosa ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Epoxy Resin ◽  
Hybrid Composite ◽  
Mass Fraction ◽  
Physical And Mechanical Properties ◽  
Particulate Composite ◽  
Modulus Of Rupture ◽  
Casting Method ◽  
Wood Sawdust ◽  
The One

These research objectives the development and evaluation of physical and mechanical properties of a hybrid composite manufactured epoxy resin reinforced by Eucalipto sp. wood sawdust and treated piassava fibers. The evaluated properties were modulus of elasticity (MOE) and modulus of rupture (MOR) in static bending, water absorption after 24 hours, porosity and apparent density. Three factors with two levels was evaluated: thickness (3 mm and 4 mm), volumetric resin fraction (45% and 50%) and the use or not of laminate piassava fibers reinforcement, leading to a factorial design of 23 type. Were manufactured four panels, two with 50% and two with 55% of resin, using casting method. For the physical and mechanical properties obtained, the better conditions were the one that uses 50% of epoxy resin, 55% sawdust mass fraction and with the use of laminated piassava fibers reinforcement. The thickness was not statistically significant in obtaining the properties evaluated.

scholarly journals Research on Mechanical Properties of Nano-modified Epoxy Resin Color Anti-skid pavement Materials

2021 ◽  
Vol 233 ◽  
pp. 01097
Author(s):  
Yongqiang Zhong
Keyword(s):  
Mechanical Properties ◽  
Epoxy Resin ◽  
Coating Material ◽  
Surface Material ◽  
Pavement Materials ◽  
Material Test ◽  
Resin Coating ◽  
Before And After ◽  
Epoxy Resin Coating ◽  
Modified Epoxy

By referring to the domestic and foreign researches on color anti-skid pavement, the composition of epoxy resin coating material for color antiskid pavement is designed. The purpose of the experiment is to analyze the effect of nano-modified epoxy resin coating by adding 2.5% nano-organic montmorillonite modifier to the existing color anti-skid pavement surface material. Test and compare the change of mechanical properties of nano-modified epoxy resin coating binder before and after nano-modified. Then the effect of nano-modification is analyzed.

Properties of Epoxy-Diane Composites Modified by Techno-Genic Fillers

2020 ◽  
Vol 299 ◽  
pp. 84-88
Author(s):  
N.Yu. Kiryushina ◽  
A.Yu. Semeykin
Keyword(s):  
Mechanical Properties ◽  
Composite Materials ◽  
Epoxy Resin ◽  
Physical And Mechanical Properties ◽  
Epoxy Polymers

The article proposes a method for producing epoxy polymers, based on epoxy resin ED-20, modified with slag from the JSC “Oskol Electrometallurgical Plant”. It has been established that it is possible to regulate physical and mechanical properties of composite materials by introducing filler, which will allow expanding its areas of application.

Interpreting research results for the physical and mechanical properties of wood: An approach not dependent on a juvenile/mature wood boundary

BioResources ◽  
2021 ◽  
Vol 16 (4) ◽  
pp. 6921-6932
Author(s):  
Tomislav Sinković ◽  
Branimir Jambreković ◽  
Tomislav Sedlar
Keyword(s):  
Mechanical Properties ◽  
Radial Direction ◽  
Statistical Tests ◽  
Physical And Mechanical Properties ◽  
Wood Properties ◽  
Mature Wood ◽  
Raw Material ◽  
Technological Properties ◽  
Wood Processing ◽  
The Difference

The interpretation and presentation of research on the physical and mechanical properties of wood in the radial direction is important for the estimation of technological properties in primary wood processing. It is common practice to define the boundary between the juvenile and mature wood zone of tree growth because of the differences in wood properties in these two zones. The juvenile and mature wood zones can be determined statistically based on the significance of the difference in the properties in a particular zone. This paper presents the insufficiency in the statistical determination of the boundary between juvenile and adult wood. Such limitations detract from the potential value and technological exploitation of wood as raw material. Statistical tests yielded zones that were too wide for the transition of juvenile wood to mature wood. Representations of the distribution of properties in the radial direction also complement the knowledge for assessing the technological properties based on the researched use of the presentation of polynomials of the second degree and the display of the Tukey HSD test in the form of comparison tables. The graphical representations by groups of the tested annual rings of fir wood also help to assess the technological properties.

Sign in / Sign up

Export Citation Format

Share Document