Interpreting research results for the physical and mechanical properties of wood: An approach not dependent on a juvenile/mature wood boundary

BioResources ◽  
2021 ◽  
Vol 16 (4) ◽  
pp. 6921-6932
Author(s):  
Tomislav Sinković ◽  
Branimir Jambreković ◽  
Tomislav Sedlar
Keyword(s):  
Mechanical Properties ◽  
Radial Direction ◽  
Statistical Tests ◽  
Physical And Mechanical Properties ◽  
Wood Properties ◽  
Mature Wood ◽  
Raw Material ◽  
Technological Properties ◽  
Wood Processing ◽  
The Difference

The interpretation and presentation of research on the physical and mechanical properties of wood in the radial direction is important for the estimation of technological properties in primary wood processing. It is common practice to define the boundary between the juvenile and mature wood zone of tree growth because of the differences in wood properties in these two zones. The juvenile and mature wood zones can be determined statistically based on the significance of the difference in the properties in a particular zone. This paper presents the insufficiency in the statistical determination of the boundary between juvenile and adult wood. Such limitations detract from the potential value and technological exploitation of wood as raw material. Statistical tests yielded zones that were too wide for the transition of juvenile wood to mature wood. Representations of the distribution of properties in the radial direction also complement the knowledge for assessing the technological properties based on the researched use of the presentation of polynomials of the second degree and the display of the Tukey HSD test in the form of comparison tables. The graphical representations by groups of the tested annual rings of fir wood also help to assess the technological properties.

scholarly journals Effects of Lizardite Addition on Technological Properties of Forsterite-Monticellite Rich White Ceramics Prepared From Natural Magnesite and Dolomite

2020 ◽  
Author(s):  
Ahmed Manni ◽  
Achraf Harrati ◽  
Abdelilah El Haddar ◽  
Abdelwahed Chari ◽  
Ali Sdiri ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Ceramic Industry ◽  
Raw Materials ◽  
Physical And Mechanical Properties ◽  
Linear Shrinkage ◽  
Thermomechanical Properties ◽  
Raw Material ◽  
Technological Properties ◽  
X Ray Diffraction ◽  
Potential Use

Abstract Lizardite rich peridotite has never been used to prepare ceramic specimens, especially in Morocco. For this raison, potential use of naturally abundant lazirditic material from the Rif domain (NW morocco), as a supply for ceramic industry, has been evaluated. The effects of lizardite addition to magnesite and dolomite mixtures on the thermomechanical properties of the calcined ceramics were also detailed. To achieve this target, natural lizardite, magnesite and dolomite samples were collected in ultrabasic Beni Bousra massif. Those raw samples were used for the synthesis of a forsterite-monticellite rich ceramics. Both raw and sintered samples were characterized by x-ray diffraction (XRD), scanning electron microscope (SEM) and fourier transform infrared (FTIR). Main physical and mechanical properties were assessed and correlated to their respective microstructural changes. The obtained results showed that both magnesite and dolomite were mainly composed of MgCO3 and CaCO3. In contrast, lizardite sample showed high amounts of silica, magnesia and iron oxide. Technological tests indicated that the prepared mixtures had increased flexural strengths. An increased amount of lizardite in the initial mixtures enhanced mechanical properties of the prepared ceramic specimens. The same data showed that lizardite has led to a decrease in linear shrinkage during calcination and subsequently, the production of ceramics with the required technological properties. Thus, the preparation of lizardite-based ceramics from the raw material deposits of the Rif area, Morocco, is technically feasible, economically justifiable and socially desirable due to the contribution to the economic growth of the raw materials sector, especially ceramic industry.

Anatomical, Chemical and Mechanical Properties of Fast-Growing Populus × Euramericana cv. ‘74/76’

IAWA Journal ◽  
2014 ◽  
Vol 35 (2) ◽  
pp. 158-169 ◽  
Author(s):  
Zhao Rongjun ◽  
Yao Chunli ◽  
Cheng Xianbao ◽  
Lu Jianxiong ◽  
Fei Benhua ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Sandy Loam ◽  
Physical And Mechanical Properties ◽  
Wood Properties ◽  
Planting Density ◽  
Dry Density ◽  
Growth Rings ◽  
Fast Growing ◽  
Breast Height ◽  
Large Growth

The anatomical characteristics, chemical composition, and physical and mechanical properties of fast-growing Populus × euramericana cv. ‘74/76’ juvenile wood were investigated. Four- to five-year-old clonal plantation trees were harvested from two different experimental sites in the suburbs of Beijing. The Shunyi site had black alkali soil with a planting density of 4 × 6 m and the Miyun site had sandy loam soil with a planting density of 3 × 5 m. The test results showed that the poplar trees from the two sites were both fast growing, with poplar at Shunyi growing faster than at Miyun. There were no significant differences in wood properties between trees grown at the two sites. Fiber length at breast height varied from 872 to 1300 μm between growth rings, average fiber width varied from 21.0 to 25.5 μm and double wall thickness varied from 5.0 to 6.6 μm. Average cellulose, lignin and hemicellulose contents in the samples were 48.9%, 25.4%, and 18.8%, respectively. MFA was higher in the first two growth rings (20–25°), and then decreased rapidly to 12° close to the bark. The average air-dry density at breast height was 401 kg/m3 while the average MOE at breast height was 9.3 GPa. The trees showed large growth rates in both height and stem diameter during the growing season. However, wood properties of the juvenile poplar appeared to be similar to those of poplars with a slower growth rate.

Influence of different concentrations of fibrinogen on the properties of a fibrin matrix for vascular tissue engineering

2021 ◽  
Vol 29 (1) ◽  
pp. 21-34
Author(s):  
Vera G. Matveeva ◽  
Mariam Yu. Khanova ◽  
Tatyana V. Glushkova ◽  
Larisa V. Antonova
Keyword(s):  
Mechanical Properties ◽  
Tissue Engineering ◽  
Metabolic Activity ◽  
Vascular Tissue ◽  
Physical And Mechanical Properties ◽  
Vascular Tissue Engineering ◽  
Test Machine ◽  
Fibrin Matrix ◽  
Before And After ◽  
The Difference

Aim. To evaluate the potential utility of fibrin matrices containing 10, 20, and 25 mg/ml of fibrinogen (fibrin-10, fibrin-20, and fibrin-30, respectively) in vascular tissue engineering (VTE). Materials and Methods. Fibrinogen was isolated using the method of ethanol cryoprecipitation and polymerized using a solution of thrombin and CaCl2. The fibrin structure was studied in a scanning electron microscope, and the physical and mechanical properties of the material were tested on a Zwick/Roell test machine. The metabolic activity of endothelial cells (EC) on the fibrin surface was evaluated by the MTT assay, and the viability of fibroblasts in the thickness of fibrin and possibility for migration by in fluorescent and light microscopy. Percent of fibrin shrinkage was determined from the difference in the sample volumes before and after removal of moisture. Results. The fiber diameter did not differ among all fibrin samples, but the pore diameter in fibrin-30 was smaller than those in fibrin-10 and fibrin-20. A possibility for migration of fibroblasts into the depth of the fibrin matrix and preservation of 97-100% viability of cells at a depth 5 mm was confirmed. The metabolic activity of EC on the surface of fibrin-20 and fibrin-30 exceeded that on collagen, fibronectin, and fibrin-10. All fibrin samples shrank in volume to 95.5-99.5%, and the highest shrinkage was seen in fibrin-10. The physical and mechanical properties of fibrin were inferior to those of human A. mammaria by a factor of 10. Conclusion. Fibrin with fibrinogen concentrations of 20 and 30 mg/ml maintains a high metabolic and proliferative activity of EC on the surface and also a high viability of fibroblasts in the matrix. Its availability, ease of preparation, and a number of other favorable properties make fibrin a promising material for VTE. However, the problem of insufficient strength requires further investigations.

scholarly journals KUALITAS PAPAN PARTIKEL BERDASARKAN KOMPOSISI SEKAM PADI DAN KAYU SENGON DENGAN VARIASI KADAR PEREKAT

2019 ◽  
Vol 7 (2) ◽  
Author(s):  
Dendi Prayoga ◽  
. Dirhamsyah ◽  
. Nurhaida
Keyword(s):  
Mechanical Properties ◽  
Moisture Content ◽  
Rice Husk ◽  
Raw Materials ◽  
Urea Formaldehyde ◽  
Physical And Mechanical Properties ◽  
Solid Content ◽  
Particle Board ◽  
Rice Husks ◽  
Wood Processing

This research aimed to examine the physical and mechanical properties of particle boards based on the composition of raw materials and adhesive content and know the treatment of the composition of raw materials and the best adhesive content and meet the standard JIS A 5908-2003. The research was conducted at Wood Workshop Laboratory, Wood Processing Laboratory Faculty of Forestry,Tanjungpura University and Laboratory of PT. Duta Pertiwi Nusantara Pontianak. The adhesive used is Urea Formaldehyde with 52% Solid Content. Comparison of the composition of rice husks and sengon varies namely rice husk 50%: sengon 50%, rice husk 60%: sengon 40% and rice husk 70%: sengon 30%  and variations in the levels of UF adhesives, namely 14% and 16%, with target density 0,7 gr/cm3. The particleboard was 30 cm x 30 cm x 1 cm Pressing at temperature 140oC for 8 minutes, with  pressure of 25 kg/cm2. The research results of the study of density and moisture content meet the standards JIS A 5908-2003. The best particle values of rice husk and sengon  with composition a ratio of  rice husk 50%: sengon 50% , 16% adhesive content  16%, with density value of  0,7072 gr/cm3, moisture content 9,1949 %, thick development 12,3210 %, water absorption 68,8270 %, MOE 12110,7273 kg/cm2, MOR 161,0025 kg/cm2, firmness sticky 1,9320 kg/cm2, screw holding strength 62,3124 kg.Keywords : adhesive, composition, particle board, rice husk, sengon

Differences in petrophysical and mechanical properties between low- and middle-rank coal subjected to liquid nitrogen cooling in coalbed methane mining

2021 ◽  
pp. 1-10
Author(s):  
Menglin Du ◽  
Feng Gao ◽  
Chengzheng Cai ◽  
Shanjie Su ◽  
Zekai Wang
Keyword(s):  
Mechanical Properties ◽  
Pore Structure ◽  
Liquid Nitrogen ◽  
Coalbed Methane ◽  
Bituminous Coal ◽  
Thermal Damage ◽  
Physical And Mechanical Properties ◽  
Damage Degree ◽  
Lignite Coal ◽  
The Difference

Abstract Exploring the damage differences between different coal rank coal reservoirs subjected to liquid nitrogen (LN2) cooling is of great significance to the rational development and efficient utilization of coalbed methane. For this purpose, the mechanical properties, acoustic emission (AE) characteristics and energy evolution law of lignite and bituminous coal subjected to LN2 cooling were investigated based on the Brazilian splitting tests. Then, pore structure changes were analyzed to reveal the difference in the microscopic damage between lignite and bituminous coal after LN2 cooling. The results showed that compared with bituminous coal, the pore structure of lignite coal changed more obviously, which was manifested as follows: significant increases in porosity, pore diameters, and pore area; a larger transformation from micropores and transition pores to mesopores and macropores. After LN2 cooling, the thermal damage inside lignite and bituminous coal was 0.412 and 0.069, respectively. The thermal damage reduced the cohesive force between mineral particles, leading to the deterioration of the macroscopic physical and mechanical properties. Simultaneously, denser AE ringing counts and larger accumulated ringing counts were observed after LN2 cooling. Moreover, the random distribution of thermal damage enhanced the randomness of the macrocrack propagation direction, resulting in an increase in the crack path tortuosity. With more initial defects inside coal, a more obvious thermal damage degree and wider damage distribution will be induced by LN2 cooling, leading to more complicated crack formation paths and a higher fragmentation degree, such as that of lignite coal.

scholarly journals Effect of waterlogging on physical and mechanical properties of Samanea saman (Jacq.) Merr. tree

2017 ◽  
Vol 52 (1) ◽  
pp. 49-52
Author(s):  
Elias ◽  
AK Das ◽  
MM Rahman ◽  
MA Islam
Keyword(s):  
Mechanical Properties ◽  
Physical Properties ◽  
Physical And Mechanical Properties ◽  
Wood Properties ◽  
Dry Density ◽  
Waterlogged Area ◽  
Mechanical And Physical Properties ◽  
Samanea Saman

This research intends to explore the mechanical and physical properties of waterlogged rain tree (Samanea saman). The variation of mechanical and physical wood properties grown in waterlogged and non-waterlogged area were studied. Four trees of the species were selected from two areas. Important mechanical and physical properties were examined for the wood of two types of trees Oven dry density for the wood of waterlogged tree was 420 kg/m3 whether it was 550 kg/m3 for the wood of non-waterlogged tree. The MOR of wood of waterlogged tree was 58.2 N/mm2 and wood of non-waterlogged tree produced 78.1 N/mm2. The MOE of the wood of waterlogged tree and non-waterlogged tree were 1478 and 4876 N/mm2. The physical and mechanical properties were lower for the wood of waterlogged tree. Such findings may in proper uses of the species.Bangladesh J. Sci. Ind. Res. 52(1), 49-52, 2017

The Effect of Lithium Alumina Silicate Phases on Elastic Modulus of Porcelain Tiles

2014 ◽  
Vol 92 ◽  
pp. 188-193 ◽  
Author(s):  
Tuna Aydin ◽  
Alpagut Kara
Keyword(s):  
Mechanical Properties ◽  
Elastic Modulus ◽  
Liquid Phase ◽  
Bulk Density ◽  
Bending Strength ◽  
Physical And Mechanical Properties ◽  
Raw Material ◽  
Closed Porosity ◽  
Low Viscosity ◽  
Porcelain Tiles

Spodumene, which is a lithium alumina silicate, has been used as a raw material in the production of thermal shock resistant whitewares and sanitarywares. The presence of spodumene results in enhancement of mullitization and imparts better physical and mechanical properties to ceramics. In this study, the influence of Lithium alumina silicate phases on the mechanical properties of standard porcelain stoneware body was investigated. Especially solid-solid reactions were observed between spodumene and quartz or spodumene and clay. These solid-solid reactions bring about a newly formed lithium alumina silicate (LAS) phases. Spodumene allows the development of a low viscosity liquid phase and results in a decrease in closed porosity, also with increase in bulk density, bending strength and elastic modulus.

Thermal and Mechanical Properties of Cyclized Polybutadiene Dielectrics

1986 ◽  
Vol 76 ◽  
Author(s):  
C. W. Wilkins ◽  
H. E. Bair ◽  
M. G. Chan ◽  
R. S. Hutton
Keyword(s):  
Mechanical Properties ◽  
Differential Scanning Calorimetry ◽  
Physical And Mechanical Properties ◽  
Mechanical Analysis ◽  
Infrared Analysis ◽  
Thermal And Mechanical Properties ◽  
Scanning Calorimetry ◽  
The Difference ◽  
Thermal Mechanical Analysis ◽  
Lower Glass Transition Temperature

ABSTRACTWe have studied some of the physical and mechanical properties of cyclized polybutadiene (CBR) dielectrics by dynamic mechanical analysis, thermal mechanical analysis, thermogravimetry, infrared analysis, and differential scanning calorimetry. Of interest is the difference in properties between thin (<30 μm) films which have been cured under vacuum and those which have been cured in air. Our results indicate that curing under vacuum prevents oxidation and reduces crosslinking. Vacuum cured films have 20% smaller moduli and 200 lower glass transition temperature than do films produced in air.

Sign in / Sign up

Export Citation Format

Share Document