Properties of Epoxy-Diane Composites Modified by Techno-Genic Fillers

2020 ◽  
Vol 299 ◽  
pp. 84-88
Author(s):  
N.Yu. Kiryushina ◽  
A.Yu. Semeykin
Keyword(s):  
Mechanical Properties ◽  
Composite Materials ◽  
Epoxy Resin ◽  
Physical And Mechanical Properties ◽  
Epoxy Polymers

The article proposes a method for producing epoxy polymers, based on epoxy resin ED-20, modified with slag from the JSC “Oskol Electrometallurgical Plant”. It has been established that it is possible to regulate physical and mechanical properties of composite materials by introducing filler, which will allow expanding its areas of application.

The Mechanical Properties of Organic Modified Epoxy Resin

2020 ◽  
Vol 43 (3) ◽  
pp. 10-14
Author(s):  
Georgel MIHU ◽  
Claudia Veronica UNGUREANU ◽  
Vasile BRIA ◽  
Marina BUNEA ◽  
Rodica CHIHAI PEȚU ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Composite Materials ◽  
Epoxy Resin ◽  
Epoxy Matrix ◽  
Epoxy Resins ◽  
Mechanical Tests ◽  
Organic Modification ◽  
Three Point Bending ◽  
Modified Epoxy

Epoxy resins have been presenting a lot of scientific and technical interests and organic modified epoxy resins have recently receiving a great deal of attention. For obtaining the composite materials with good mechanical proprieties, a large variety of organic modification agents were used. For this study gluten and gelatin had been used as modifying agents thinking that their dispersion inside the polymer could increase the polymer biocompatibility. Equal amounts of the proteins were milled together and the obtained compound was used to form 1 to 5% weight ratios organic agents modified epoxy materials. To highlight the effect of these proteins in epoxy matrix mechanical tests as three-point bending and compression were performed.

scholarly journals Physical and Mechanical Properties of Natural Leaf Fiber-Reinforced Epoxy Polyester Composites

Polymers ◽  
2021 ◽  
Vol 13 (9) ◽  
pp. 1369
Author(s):  
Sanjeev Kumar ◽  
Lalta Prasad ◽  
Vinay Kumar Patel ◽  
Virendra Kumar ◽  
Anil Kumar ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Composite Materials ◽  
Synthetic Fibre ◽  
Low Cost ◽  
Fibre Length ◽  
Physical And Mechanical Properties ◽  
Natural Fibres ◽  
Risk Environment ◽  
Insulation Property ◽  
Natural Leaf

In recent times, demand for light weight and high strength materials fabricated from natural fibres has increased tremendously. The use of natural fibres has rapidly increased due to their high availability, low density, and renewable capability over synthetic fibre. Natural leaf fibres are easy to extract from the plant (retting process is easy), which offers high stiffness, less energy consumption, less health risk, environment friendly, and better insulation property than the synthetic fibre-based composite. Natural leaf fibre composites have low machining wear with low cost and excellent performance in engineering applications, and hence established as superior reinforcing materials compared to other plant fibres. In this review, the physical and mechanical properties of different natural leaf fibre-based composites are addressed. The influences of fibre loading and fibre length on mechanical properties are discussed for different matrices-based composite materials. The surface modifications of natural fibre also play a crucial role in improving physical and mechanical properties regarding composite materials due to improved fibre/matrix adhesion. Additionally, the present review also deals with the effect of silane-treated leaf fibre-reinforced thermoset composite, which play an important role in enhancing the mechanical and physical properties of the composites.

scholarly journals Effect of Structural Differences on the Mechanical Properties of 3D Integrated Woven Spacer Sandwich Composites

Materials ◽  
2021 ◽  
Vol 14 (15) ◽  
pp. 4284
Author(s):  
Lvtao Zhu ◽  
Mahfuz Bin Rahman ◽  
Zhenxing Wang
Keyword(s):  
Mechanical Properties ◽  
Composite Materials ◽  
Three Dimensional ◽  
Sheet Thickness ◽  
Physical And Mechanical Properties ◽  
Sandwich Composites ◽  
Computed Tomography Images ◽  
And Performance ◽  
Industrial Textiles ◽  
Load Conditions

Three-dimensional integrated woven spacer sandwich composites have been widely used as industrial textiles for many applications due to their superior physical and mechanical properties. In this research, 3D integrated woven spacer sandwich composites of five different specifications were produced, and the mechanical properties and performance were investigated under different load conditions. XR-CT (X-ray computed tomography) images were employed to visualize the microstructural details and analyze the fracture morphologies of fractured specimens under different load conditions. In addition, the effects of warp and weft direction, face sheet thickness, and core pile height on the mechanical properties and performance of the composite materials were analyzed. This investigation can provide significant guidance to help determine the structure of composite materials and design new products according to the required mechanical properties.

Physical and mechanical properties of triacetate fibre modified with ED-5 epoxy resin

1972 ◽  
Vol 3 (3) ◽  
pp. 303-305
Author(s):  
Z. Yu. Sakalauskas ◽  
Ya. K. Matskevichene ◽  
Yu. I. Baltakite ◽  
I. I. Zdanavichyus
Keyword(s):  
Mechanical Properties ◽  
Epoxy Resin ◽  
Physical And Mechanical Properties ◽  
Triacetate Fibre

Effect of Wood Filler Concentration on Physical and Mechanical Properties of PLA-Based Composites

2021 ◽  
Vol 887 ◽  
pp. 110-115
Author(s):  
G.A. Sabirova ◽  
R.R. Safin ◽  
N.R. Galyavetdinov
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Elastic Modulus ◽  
Composite Materials ◽  
Impact Strength ◽  
Wood Flour ◽  
Experimental Studies ◽  
Physical And Mechanical Properties ◽  
Filler Concentration ◽  
High Concentration

This paper presents the findings of experimental studies of the physical and mechanical properties of wood-filled composites based on polylactide (PLA) and vegetable filler in the form of wood flour (WF) thermally modified at 200-240 °C. It also reveals the dependence of the tensile strength, impact strength, bending elastic modulus, and density of composites on the amount of wood filler and the temperature of its thermal pre-modification. We established that an increase in the concentration of the introduced filler and the degree of its heat treatment results in a decrease of the tensile strength, impact strength and density of composite materials, while with a lower binder content, thermal modification at 200 °C has a positive effect on bending elastic modulus. We also found that 40 % content of a wood filler heated to 200 °C is sufficient to maintain relatively high physical and mechanical properties of composite materials. With a higher content of a wood filler, the cost can be reduced but the quality of products made of this material may significantly deteriorate. However, depending on the application and the life cycle of this product, it is possible to develop a formulation that includes a high concentration of filler.

scholarly journals THE EFFECT OF COCONUT COIR FIBER POWDER CONTENT AND HARDENER WEIGHT FRACTIONS ON MECHANICAL PROPERTIES OF AN EPR-174 EPOXY RESIN COMPOSITE

SINERGI ◽  
2021 ◽  
Vol 25 (3) ◽  
pp. 361
Author(s):  
Muhamad Fitri ◽  
Shahruddin Mahzan ◽  
Imam Hidayat ◽  
Nurato Nurato
Keyword(s):  
Mechanical Properties ◽  
Shear Strength ◽  
Composite Materials ◽  
Impact Strength ◽  
Epoxy Resin ◽  
Resin Composite ◽  
Weight Fraction ◽  
Resin Matrix ◽  
Powder Content ◽  
Made In

The development of composite materials is increasingly widespread, which require superior mechanical properties. From many studies, it is found that the mechanical properties of composite materials are influenced by various factors, including the reinforcement content, both in the form of fibers and particle powder. However, those studies have not investigated the effect of the hardener weight fraction on the mechanical properties of resin composite materials. Even though its function as a hardener is likely to affect its mechanical properties, it might obtain the optimum composition of the reinforcing content and hardener fraction to get the specific mechanical properties. This study examines the effect of hardener weight fraction combined with fiber powder content on mechanical properties of EPR-174 epoxy resin matrix composite and determines the optimum of Them. The research was conducted by testing a sample of composite matrix resin material reinforced with coconut fiber powder. The Powder content was made in 3 levels, i.e.: 6%, 8%, and 10%. While the hardener fraction of resin was made in 3 levels, i.e.: 0.4, 0.5, and 0.6. The test results showed that pure resin had the lowest impact strength of 1.37 kJ/m2. The specimen with a fiber powder content of 6% has the highest impact strength i.e.: 4.92 kJ/m2. The hardener fraction of 0.5 has the highest impact strength i.e.: 4.55 kJ/m2. The fiber powder content of 8% produced the highest shear strength i.e.: 1.00 MPa. Meanwhile, the hardener fraction of 0.6 has the highest shear strength i.e.: 2.03 MPa.

scholarly journals METHOD OF SAMPLE MANUFACTURING FROM MULTILAYER COMPOSITE MATERIALS FOR STUDYING THEIR MECHANICAL PROPERTIES

2018 ◽  
pp. 16-23
Author(s):  
Alsaid Mazen ◽  
Ali Salamekh
Keyword(s):  
Mechanical Properties ◽  
Composite Materials ◽  
Polymer Composite ◽  
Testing Machine ◽  
Physical And Mechanical Properties ◽  
Polymer Composite Materials ◽  
Technological Parameters ◽  
Cutting Out ◽  
Method Of Production ◽  
Economic Considerations

In the last decades there is increasing the need to apply polymer composite materials in different industries, particularly in shipbuilding. There are developing single structures made from polymer composite materials to be used on board ships. The article focuses on technology of manufacturing slabs from polymer composite materials to carry out mechanical testing in the laboratory special standard units. Mechanical properties of polymer composite materials depend on molding technologies. There has been described a technology of sample manufacturing from polymer composite materials reinforced with glass fiber mat with fiberglass plastics. The technique of testing the specified samples for tensile strength has been considered. The sizes and shapes of the samples as well as the technological parameters of the manufacturing process have been validated, depending on the standard requirements and the technological features of the testing machine. The physical and mechanical properties of the components that make up the composite materials are considered. The sequence of stacking layers for preparation of plates from composite materials is indicated. The dimensions of the plates for cutting out finished samples are determined, depending on the method of production. The way of laying plates from composite materials has been chosen on the base of economic considerations and conditions of accessibility. The obtained results of mechanical properties can be used in solving problems of application of polymer composite materials in shipbuilding, for example, in manufacturing superstructures of some dry cargo vessels.

Thermo Mechanical behaviour of Phenol Novolac Resin and Unsaturated Polyester Toughened Epoxy using nano Bentonite and Silica Nanoparticles

2020 ◽  
Vol 1 (3) ◽  
pp. 77-83
Keyword(s):  
Mechanical Properties ◽  
Epoxy Resin ◽  
Silica Nanoparticles ◽  
Moisture Absorption ◽  
Unsaturated Polyester ◽  
Physical And Mechanical Properties ◽  
Bending Test ◽  
Mechanical And Thermal Properties ◽  
Novolac Epoxy ◽  
Industrial Needs

Phenol novolac epoxy resin is a polymer matter which its properties can be modified for industrial needs. In this research, nanocomposites of phenol novolac epoxy resin and unsaturated polyester are made nano Bentonite and silica nanoparticles as filler. For this purpose, effect of nanoparticles percent on nanocomposite formation is studied and their physical, mechanical and thermal properties are obtained. The presence of unsaturated polyester in this process forms a cross-link capable of improving the physical and mechanical properties of epoxy resin. Fracture behavior was determined by a SEM device. Moreover, TGA, DSC, impact tests and bending test were applied for data analysis. When process ability is growing, moisture absorption decreases. Fracture toughness was also evaluated in a stoichiometric network. Physical and mechanical properties improve significantly with increasing nanoparticles. The most important reason for using this nanocomposite is its high resistance to corrosion.

Sign in / Sign up

Export Citation Format

Share Document