scholarly journals Estimative of Wooden Toughness by the Apparent Density and Bending Strength

2014 ◽  
Vol 4 (2) ◽  
pp. 49-55 ◽  
Author(s):  
Silva Sérgio Augusto Mello da ◽  
Panzera Túlio Hallak ◽  
Lahr Francisco Antonio Rocco ◽  
Christoforo André Luis
Keyword(s):  
Apparent Density ◽  
Bending Strength

Fabrication of Stainless Steel Foams Using Polymeric Sponge Impregnation Technology

2014 ◽  
Vol 1035 ◽  
pp. 219-224 ◽  
Author(s):  
Hui Wang ◽  
Xiang Yang Zhou ◽  
Bo Long
Keyword(s):  
Stainless Steel ◽  
Apparent Density ◽  
Open Porosity ◽  
316L Stainless Steel ◽  
Bending Strength ◽  
Sintering Temperature ◽  
Foam Sample ◽  
Cell Network ◽  
Mass Fractions ◽  
Steel Foam

316L stainless steel foams (SSFs) are fabricated successfully by polymeric sponge impregnation technology. The effects of mass fractions of PVA and powder on LOAD in impregnated sponge samples are investigated, and the effects of sintering temperature on apparent density, open porosity and bending strength of SSFs samples are also discussed. The experimental results show that the impregnated sponge samples may hold excellent 3D open-cell network structure and uniform muscles when the mass fractions of PVA and powder in slurry are kept in 9-13 % and 52-75% respectively; with rising the sintering temperature, the apparent density and bending strength of SSFs gradually increases, the open porosity reduces. After the temperature exceeds 1260°C, the bending strength reduces oppositely. A stainless steel foam sample with open porosity of 81.4% and bending strength of about 56.8 Mpa can be obtained after sintering at 1260 °Cfor 30min.

scholarly journals Influence of the Matrix Grain Size on the Apparent Density and Bending Strength of Sand Cores

2017 ◽  
Vol 17 (1) ◽  
pp. 27-30
Author(s):  
R. Dańko
Keyword(s):  
Grain Size ◽  
Apparent Density ◽  
Bending Strength ◽  
Diffraction Method ◽  
Laser Diffraction ◽  
Grain Sizes ◽  
The Matrix

Abstract The results of investigations of the influence of the matrix grain sizes on properties of cores made by the blowing method are presented in the hereby paper. Five kinds of matrices, differing in grain size compositions, determined by the laser diffraction method in the Analysette 22NanoTec device, were applied in investigations. Individual kinds of matrices were used for making core sands in the Cordis technology. From these sands the shaped elements, for determining the apparent density of compacted sands and their bending strength, were made by the blowing method. The shaped elements (cores) were made at shooting pressures being 3, 4 and 5 atn. The bending strength of samples were determined directly after their preparation and after the storing time of 1 hour.

The Effect of Slip Loading on the Properties of Porous Calcium Phosphate Bioceramics

2007 ◽  
Vol 361-363 ◽  
pp. 19-22 ◽  
Author(s):  
Y.H. Hsu ◽  
I.G. Turner ◽  
A.W. Miles
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
Calcium Phosphate ◽  
Apparent Density ◽  
Bending Strength ◽  
Physical And Mechanical Properties ◽  
Four Point Bending ◽  
Work Of Fracture

Ceramic slips with powder loadings in the range of 80-140 wt% were used to investigate the effect of slip loading on the physical and mechanical properties of open pore HA/TCP bioceramics. The results indicated that increasing the slip loading had an effect on the properties of the samples. The average apparent density, the work of fracture and compressive strength all increased with slip loading. In contrast, the effect of increasing slip loading on the four-point bending strength was not significant.

Study of the apparent density in 7 m industrial coke ovens

1989 ◽  
Vol 86 (5) ◽  
pp. 387-392
Author(s):  
W. Eisenhut ◽  
F. Huhn ◽  
F. Strelow
Keyword(s):  
Apparent Density ◽  
Coke Ovens

Study Of Structure Formation Of Organic-Mineral Compositions With Fibrous Filler By Electron Microscopy Method

2019 ◽  
pp. 41-47
Keyword(s):  
Electron Microscopy ◽  
Structure Formation ◽  
Mineral Composition ◽  
Bending Strength ◽  
Cement Stone ◽  
Hydrated Cement ◽  
Fibrous Filler ◽  
Organic Mineral ◽  
Microscopy Method ◽  
Mineral Compositions

The article presents the study of processes of structure formation of cement stone and products of hardening of organic-mineral compositions with fibrous filler (shavings) by the electronic scanning microscopy method. It is established that the additive-free cement stone at the age of 28 days has a dense and homogeneous structure, consists of calcium hydro-silicates, Portlandite and calcite - newgrowths characteristic for cement systems. Cellulose fibers, which make up the bulk of the substance of shavings, are sufficiently active, which determines the high adhesion of the hydration products of the cement binder to their surface. It is shown that the introduction of shavings into the organo-mineral composition leads to inhibition of cement hydration processes. Organo-mineral compositions with different shavings content (two compositions) were analyzed. The first composition is characterized by a fairly dense structure, the cement stone consists of globular nanoscale nuclei of hydrosilicates, Portlandite and calcite. The second composition has a loose porous structure, cement stone consists of non-hydrated cement grains, newgrowths are represented by calcite and vaterite. The structure of the contact zone "osprey fiber-cement stone" in the organo-mineral composition of the first composition indicates a good adhesion of the filler surface with the phases of hydrated cement. The use of shavings as a fibrous filler (the first composition) increases the tensile and bending strength, as well as the wear resistance of organo-mineral compositions. The data obtained by scanning electron microscopy are confirmed by the results of studying the processes of structure formation of cement stone by quantitative x-ray phase analysis.

Performance enhancement of normal contact ratio gearing system through correction factor

2019 ◽  
Vol 13 (3) ◽  
pp. 5242-5258
Author(s):  
R. Ravivarman ◽  
K. Palaniradja ◽  
R. Prabhu Sekar
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Correction Factor ◽  
Bending Strength ◽  
Performance Enhancement ◽  
Transmission Ratio ◽  
Contact Ratio ◽  
Element Analysis ◽  
Normal Contact ◽  
Root Region

As lined, higher transmission ratio drives system will have uneven stresses in the root region of the pinion and wheel. To enrich this agility of uneven stresses in normal-contact ratio (NCR) gearing system, an enhanced system is desirable to be industrialized. To attain this objective, it is proposed to put on the idea of modifying the correction factor in such a manner that the bending strength of the gearing system is improved. In this work, the correction factor is modified in such a way that the stress in the root region is equalized between the pinion and wheel. This equalization of stresses is carried out by providing a correction factor in three circumstances: in pinion; wheel and both the pinion and the wheel. Henceforth performances of this S+, S0 and S- drives are evaluated in finite element analysis (FEA) and compared for balanced root stresses in parallel shaft spur gearing systems. It is seen that the outcomes gained from the modified drive have enhanced performance than the standard drive.

Bending Strength of Steel Fibre Reinforced Concrete Ribbed Slab Panel

2018 ◽  
Vol 15 (1) ◽  
pp. 15
Author(s):  
AMIR SYAFIQ SAMSUDIN ◽  
MOHD HISBANY MOHD HASHIM ◽  
SITI HAWA HAMZAH ◽  
AFIDAH ABU BAKAR
Keyword(s):  
Reinforced Concrete ◽  
Bending Strength ◽  
Steel Fibre ◽  
Concrete Slab ◽  
Future Application ◽  
Fibre Reinforcement ◽  
Fibre Reinforced Concrete ◽  
Conventional Concrete ◽  
Steel Fibre Reinforced Concrete ◽  
Bending Load

Nowadays, demands in the application of fibre in concrete increase gradually as an engineering material. Rapid cost increment of material causes the increase in demand of new technology that provides safe, efficient and economical design for the present and future application. The introduction of ribbed slab reduces concrete materials and thus the cost, but the strength of the structure also reduces due to the reducing of material. Steel fibre reinforced concrete (SFRC) has the ability to maintain a part of its tensile strength prior to crack in order to resist more loading compared to conventional concrete. Meanwhile, the ribbed slab can help in material reduction. This research investigated on the bending strength of 2-ribbed and 3-ribbed concrete slab with steel fibre reinforcement under static loading with a span of 1500 mm and 1000 mm x 75 mm in cross section. An amount of 40 kg/m steel fibre of all total concrete volume was used as reinforcement instead of conventional bars with concrete grade 30 N/mm2. The slab was tested under three-point bending. Load versus deflection curve was plotted to illustrate the result and to compare the deflection between control and ribbed slab. This research shows that SFRC Ribbed Slab capable to withstand the same amount of load as normal slab structure, although the concrete volume reduces up to 20%.

Ceramic Materials. Effects of Fracture Origin and Microstructure on Bending Strength of High-Strength Si3N4.

1994 ◽  
Vol 43 (489) ◽  
pp. 599-605 ◽  
Author(s):  
Akira YAMAKAWA ◽  
Takehisa YAMAMOTO ◽  
Tomoyuki AWAZU ◽  
Kenji MATSUNUMA ◽  
Takao NISHIOKA
Keyword(s):  
Bending Strength ◽  
High Strength ◽  
Ceramic Materials ◽  
Fracture Origin

Structure and properties of compact articles from high-alloyed iron powder with adding of boron nitride

2020 ◽  
pp. 39-48
Author(s):  
B. O. Bolshakov ◽  
◽  
R. F. Galiakbarov ◽  
A. M. Smyslov ◽  
◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Boron Nitride ◽  
Grain Boundary ◽  
Bending Strength ◽  
Physical And Mechanical Properties ◽  
Operating Conditions ◽  
Structure And Properties ◽  
Steam Turbines ◽  
Friction Forces ◽  
Wide Range

The results of the research of structure and properties of a composite compact from 13 Cr – 2 Мо and BN powders depending on the concentration of boron nitride are provided. It is shown that adding boron nitride in an amount of more than 2% by weight of the charge mixture leads to the formation of extended grain boundary porosity and finely dispersed BN layers in the structure, which provides a high level of wearing properties of the material. The effect of boron nitride concentration on physical and mechanical properties is determined. It was found that the introduction of a small amount of BN (up to 2 % by weight) into the compacts leads to an increase in plasticity, bending strength, and toughness by reducing the friction forces between the metal powder particles during pressing and a more complete grain boundary diffusion process during sintering. The formation of a regulated structure-phase composition of powder compacts of 13 Cr – 2 Mо – BN when the content of boron nitride changes in them allows us to provide the specified physical and mechanical properties in a wide range. The obtained results of studies of the physical and mechanical characteristics of the developed material allow us to reasonably choose the necessary composition of the powder compact for sealing structures of the flow part of steam turbines, depending on their operating conditions.

Materials for bullet core

2020 ◽  
Vol 2020 (10) ◽  
pp. 8-21
Author(s):  
A. G. Kolmakov ◽  
◽  
I. O. Bannykh ◽  
V. I. Antipov ◽  
L. V. Vinogradov ◽  
...  
Keyword(s):  
High Speed ◽  
Bending Strength ◽  
Low Alloy Steels ◽  
Hard Alloys ◽  
Small Arms ◽  
Alloy Steels ◽  
Materials Used ◽  
Basic Ideas ◽  
New Generation ◽  
Natural Composite

he basic ideas about the process of introducing cores into protective barriers and the most common core patterns and their location in conventional and sub-caliber small arms bullets are discussed. The materials used for manufacture of cores are analyzed. It is concluded that for mass bullets of increased armor penetration the most rational choice can be considered the use of high-carbon low-alloy steels of a new generation with a natural composite structure and hardness of up to 70 HRC. For specialized armor-piercing bullets, cores made from promising economically-alloyed high-speed steels characterized by a high complex of «hardness—bending strength» are better alternative than ones made of hard alloys or tungsten alloys.

Sign in / Sign up

Export Citation Format

Share Document