scholarly journals The Effects of Mineral Wool Fly Ash on Cohesive Soil Strength Behaviour

2021 ◽  
Vol 16 (4) ◽  
pp. 192-211
Author(s):  
Mindaugas Zakarka ◽  
Šarūnas Skuodis ◽  
Rimantas Mackevičius ◽  
Danutė Sližytė
Keyword(s):  
Compressive Strength ◽  
Fly Ash ◽  
Portland Cement ◽  
Research Work ◽  
Cohesive Soil ◽  
Soil Strength ◽  
Mineral Wool ◽  
Sand Mixture ◽  
Strength Change ◽  
Dry Mixing

This research work represents updated results of cohesive soil strength improvement with mineral wool fly ash. In the investigations, these materials were used: Portland cement CEM I 42.5 R, fly ash obtained from a mineral wool production process, sand and clay. Mixtures were prepared as follows: dry mixing of Portland cement and fly ash; dry mixing of sand and clay; adding water into Portland cement and fly ash; adding sand and clay mixture into already prepared Portland cement and fly ash suspension. The content of fly ash replacing Portland cement varied from 0% to 40%, and the content of sand mixture varied from 20% to 60%. After 24 hours, investigated samples were taken out from cylinder forms and kept in a desiccator with a humidity of 90% and at 20 °C temperature. Uniaxial compressive strength of the samples was determined after 548 days and compared to previous research results obtained after 7, 28 and 183 days. The most predictable compressive strength is for samples, which composition is 100% cement and 0% fly ash. In these samples, the highest compressive strength was obtained, comparing them to the other investigated samples. Compressive strength change is minimal for samples with a 10–30% amount of fly ash. The most significant decrease in compressive strength was obtained for samples with a 40% fly ash after 183 days. Nonetheless, the compressive strength of these samples increased after 548 days and is almost the same as for samples with 100% Portland cement.

scholarly journals STABILIZATION OF CLAY POWDER WITH MINERAL WOOL FLY ASH

2020 ◽  
Vol 11 (4) ◽  
pp. 106-113
Author(s):  
Mindaugas Zakarka ◽  
Rimantas Mackevičius ◽  
Šarūnas Skuodis ◽  
Danutė Sližytė ◽  
Andrius Kudžma
Keyword(s):  
Compressive Strength ◽  
Fly Ash ◽  
Portland Cement ◽  
Clay Soil ◽  
Research Work ◽  
Mineral Wool ◽  
Soil Samples ◽  
Short Term ◽  
Optimal Ratio

The aim of this article – to determine short term and long term strengthening of clay soil, by strengthening it with fly ash obtained during the production of mineral wool. This article introduces research which is used to determine the optimal ratio of fly ash in cement suspension for strengthening of clay soil. Samples which were investigated in this research work prepared by mixing Portland cement, mineral wool fly ash, clay powder, sand and water. All investigated samples compressive strength after 6 months exceeded 1.7 MPa. It is enough of such strength in geotechnics to conduct strengthening of soil and it is possible to argue that soil is strengthened.

scholarly journals Environment friendly concrete block made from Portland cement and aggregate replacement materials

2021 ◽  
Vol 2145 (1) ◽  
pp. 012032
Author(s):  
B Kaewsai ◽  
P Torkittikul ◽  
A Chaipanich
Keyword(s):  
Compressive Strength ◽  
Fly Ash ◽  
Portland Cement ◽  
Research Work ◽  
Bottom Ash ◽  
Concrete Block ◽  
Total Solid ◽  
Solid Mass ◽  
Environment Friendly ◽  
Stone Dust

Abstract This research work investigated the properties of concrete block made from Portland cement and aggregate replacement materials. Portland cement (PC) was replaced by fly ash (FA) at 10%, 20%, 30% and sand was replaced by bottom ash (BA) at 10% by weight. Water was used at 7% by weight of total solid mass. Binder : Sand : Stone dust ratio of 1 : 5 : 6, 1 : 4 : 5 and 1 : 3.5 : 4.5 were used. Compressive strength were tested after curing in air for 28 days. The results showed that compressive strength of 1 : 5 : 6 ratio was lower than others. Concrete block replaced PC by fly ash had lower compressive strength when amount of fly ash increased. Concrete block had lower compressive strength when replaced sand by bottom ash. As a result, the mixes with FA as PC replacement and BA as sand replacement at the ratio of 1 : 5 : 6 did not meet the requirement of Thai industrial standard. However, concrete block with PC replaced by fly ash at 10%, 20% and sand replaced by bottom ash at 10% of 1 : 3.5 : 4.5 ratio was higher than 1 : 5 : 6 ratio and this ratio meet the requirement of Thai industrial standard.

COMPRESSIVE STRENGTH AND THERMAL CONDUCTIVITY OF WATER AND AIR CURED PORTLAND CEMENT-FLY ASH-SILICA FUME MORTARS

2018 ◽  
Vol 17 (9) ◽  
pp. 2023-2030
Author(s):  
Arnon Chaipanich ◽  
Chalermphan Narattha ◽  
Watcharapong Wongkeo ◽  
Pailyn Thongsanitgarn
Keyword(s):  
Thermal Conductivity ◽  
Compressive Strength ◽  
Fly Ash ◽  
Portland Cement ◽  
Silica Fume

Development of Sediment Brick Utilizing Reservoir Sediment and Fly Ash

2013 ◽  
Vol 420 ◽  
pp. 276-280
Author(s):  
Bashar S. Mohammed ◽  
Ean Lee Woen ◽  
M.A. Malek ◽  
Wong Leong Sing ◽  
Nor Aishah Abbas ◽  
...  
Keyword(s):  
Compressive Strength ◽  
Fly Ash ◽  
Power Plants ◽  
Gravitational Force ◽  
Electrical Power ◽  
Research Work ◽  
Flowing Water ◽  
Reservoir Sediment ◽  
Load Bearing ◽  
Hydroelectric Plants

Electrical companies generate electricity mainly from two major types of plant; hydroelectric plants and thermal plants. Hydroelectric is the term referring to electricity generated by hydropower; the production of electrical power through the use of the gravitational force of falling or flowing water through dams operation. The sedimentation of such dams over years will cause large capacity losses of the dams. Thermal plants generate electricity through coal-fired power plants which produce millions tons of fly ash yearly. This fly ash accumulates rapidly and causes enormous problems of disposal. Therefore, the research work presented in this paper is dealing with utilizing reservoir sediment and fly as to form brick under pressure. Sediment brick can be produced as a load bearing brick with compressive strength is greater than 7 N/mm2.

scholarly journals Hydration study of mechanically activated mixtures of Portland cement and fly ash

2007 ◽  
Vol 72 (6) ◽  
pp. 591-604 ◽  
Author(s):  
Gordana Stefanovic ◽  
Ljubica Cojbasic ◽  
Zivko Sekulic ◽  
Srdjan Matijasevic
Keyword(s):  
Compressive Strength ◽  
Fly Ash ◽  
Portland Cement ◽  
Mechanical Activation ◽  
Early Period ◽  
Negative Effects ◽  
Early Hydration ◽  
Cement Pastes ◽  
Dta And Tg ◽  
Low Activity

Fly ash (FA) can be used in cement mixtures with certain limitations. The problem of the mentioned mixtures lies in the insufficient activity of the particles of FA in the reactions which are important for the establishment of the mechanical characteristics of cement. This is particularly true for the hydration reactions. As a result of this, cement pastes formed by mixing ash and clinker have worse characteristics compared to those of pure Portland cement (PC), especially in the early period of setting. As is well known, FA can be a good solution for the neutralization of the negative effects generated due to the creation of free Ca(OH)2 during the hydration of PC, provided that the problems with the low activity of FAare overcome. For the experiments in this study, a mixture of Portland cement and fly ash was used, the content of ash in the mixture being 30 % and 50 %. Mechanical activation was performed in a vibrating ring mill. The goal of this study was to demonstrate, through experimental results, that during the mechanical activation of a PC and FA mixture, the components in the mixture which mostly affect the direction, rate and range of hydration reactions occurring in the mixture had been activated. The values of the compressive strength of the activated and non-activated mixtures and the changes of their specific surface area proved that during the grinding process, the mixture PC+FA had been mechanically activated. The highest increase of compressive strength was achieved in the early period of setting, which indicates an improvement in the early hydration of the mixture. XRD, DTA and TG analyses showed that the alite (C3S) and belite (C2S) from the PC and a part of the fly ash were activated. .

scholarly journals Study of Proportional Variation of Geopolymer Concrete which Self Compacting Concrete

2019 ◽  
Vol 2 (2) ◽  
pp. 65
Author(s):  
Purwanto P. ◽  
Himawan Indarto
Keyword(s):  
Compressive Strength ◽  
Fly Ash ◽  
Power Plant ◽  
Portland Cement ◽  
Fine Aggregate ◽  
Geopolymer Concrete ◽  
Conventional Concrete ◽  
Basic Characteristics ◽  
Carbon Dioxide Co2 ◽  
Proportional Variation

Portland cement production process which is the conventional concrete constituent materials always has an impact on producing carbon dioxide (CO2) which will damage the environment. To maintain the continuity of development, while maintaining the environment, Portland cement substitution can be made with more environmentally friendly materials, namely fly ash. The substitution of fly ash material in concrete is known as geopolymer concrete. Fly ash is one of the industrial waste materials that can be used as geopolymer material. Fly ash is mineral residue in fine grains produced from coal combustion which is mashed at power plant power plant [15]. Many cement factories have used fly ash as mixture in cement, namely Portland Pozzolan Cement. Because fly ash contains SiO2, Al2O3, P2O3, and Fe2O3 which are quite high, so fly ash is considered capable of replacing cement completely.This study aims to obtain geopolymer concrete which has the best workability so that it is easy to work on (Workable Geopolymer Concrete / Self Compacting Geopolymer Concrete) and obtain the basic characteristics of geopolymer concrete material in the form of good workability and compressive strength. In this study, geopolymer concrete is composed of coarse aggregate, fine aggregate, fly ash type F, and activators in the form of NaOH and Na2SiO3 Be52. In making geopolymer concrete, additional ingredients such as superplastizer are added to increase the workability of geopolymer concrete. From this research, the results of concrete compressive strength above fc' 25 MPa and horizontal slump values reached 60 to 80 centimeters.

scholarly journals Biofuel Combustion Fly Ash Influence on the Properties of Concrete

2016 ◽  
Vol 7 (5) ◽  
pp. 546-550
Author(s):  
Aurelijus Daugėla ◽  
Džigita Nagrockienė ◽  
Laurynas Zarauskas
Keyword(s):  
Compressive Strength ◽  
Fly Ash ◽  
Portland Cement ◽  
Water Absorption ◽  
Frost Resistance ◽  
Ash Content ◽  
Mineral Admixtures ◽  
Binding Agent ◽  
Materials Used ◽  
Plasticizing Admixture

Cement as the binding agent in the production of concrete can be replaced with active mineral admixtures. Biofuel combustion fly ash is one of such admixtures. Materials used for the study: Portland cement CEM I 42.5 R, sand of 0/4 fraction, gravel of 4/16 fraction, biofuel fly ash, superplasticizer, water. Six compositions of concrete were designed by replacing 0%, 5%, 10%, 15% 20%, and 25% of cement with biofuel fly ash. The article analyses the effect of biofuel fly ash content on the properties of concrete. The tests revealed that the increase of biofuel fly ash content up to 20% increases concrete density and compressive strength after 7 and 28 days of curing and decreases water absorption, with corrected water content by using plasticizing admixture. It was found that concrete where 20% of cement is replaced by biofuel ash has higher frost resistance.

scholarly journals Protective Geopolymer Coatings Containing Multi-Componential Precursors: Preparation and Basic Properties Characterization

Materials ◽  
2020 ◽  
Vol 13 (16) ◽  
pp. 3448
Author(s):  
Chenhui Jiang ◽  
Aiying Wang ◽  
Xufan Bao ◽  
Zefeng Chen ◽  
Tongyuan Ni ◽  
...  
Keyword(s):  
Compressive Strength ◽  
Blast Furnace ◽  
Fly Ash ◽  
Portland Cement ◽  
Adhesive Strength ◽  
Blast Furnace Slag ◽  
Setting Time ◽  
Rapid Test ◽  
Granulated Blast Furnace Slag ◽  
Furnace Slag

This paper presents an experimental investigation on geopolymer coatings (GPC) in terms of surface protection of civil structures. The GPC mixtures were prepared with a quadruple precursor simultaneously containing fly ash (FA), ground granulated blast-furnace slag (GBFS), metakaolin (MK), and Portland cement (OPC). Setting time, compressive along with adhesive strength and permeability, were tested and interpreted from a perspective of potential applications. The preferred GPC with favorable setting time (not shorter than 120 min) and desirable compressive strength (not lower than 35 MPa) was selected from 85 mixture formulations. The results indicate that balancing strength and setting behavior is viable with the aid of the multi-componential precursor and the mixture design based on total molar ratios of key oxides or chemical elements. Adhesive strength of the optimized GPC mixtures was ranged from 1.5 to 3.4 MPa. The induced charge passed based on a rapid test of coated concrete specimens with the preferred GPC was 30% lower than that of the uncoated ones. Setting time of GPC was positively correlated with η[Si/(Na+Al)]. An abrupt increase of setting time occurred when the molar ratio was greater than 1.1. Compressive strength of GPC was positively affected by mass contents of ground granulated blast furnace slag, metakaolin and ordinary Portland cement, and was negatively affected by mass content of fly ash, respectively. Sustained seawater immersion impaired the strength of GPC to a negligible extent. Overall, GPC potentially serves a double purpose of satisfying the usage requirements and achieving a cleaner future.

Influence of Fly Ash and Basalt Fibers on Strength and Chloride Penetration Resistance of Self-Consolidating Concrete

2016 ◽  
Vol 866 ◽  
pp. 3-8 ◽  
Author(s):  
Osama Ahmed Mohamed ◽  
Waddah Al Hawat
Keyword(s):  
Compressive Strength ◽  
Fly Ash ◽  
Portland Cement ◽  
Strength Properties ◽  
Chloride Penetration ◽  
Partial Replacement ◽  
Basalt Fibers ◽  
Self Consolidating Concrete ◽  
Chloride Penetration Resistance ◽  
Hardened Properties

Fly ash is a sustainable partial replacement of Portland cement that offers significant advantages in terms of fresh and hardened properties of concrete. This paper presents the findings of a study that aims at assessing the durability and strength properties of sustainable self-consolidating concrete (SCC) mixes in which Portland cement was partially replaced with 10%, 20%, 30%, and 40% fly ash. The study confirms that replacing Portland cement with fly ash at all of the percentages studied improves resistance of concrete to chloride penetration. The 40% fly ash mix exhibited the highest resistance to chloride penetration compared to the control mix. Despite the relative drop in compressive strength after 7 days of curing, the 28-day compressive strength of 40% SCC mix reached 55.75 MP, which is very close to the control mix. The study also confirms that adding 1%, 1.5%, and 2% basalt fibers, respectively, to the 40% fly ash mix improves the resistance to chloride penetration compared to the mix without basalt fibers.

Sign in / Sign up

Export Citation Format

Share Document