scholarly journals Effects of Oxygenated Additives with Diesel on the Performance of D I Diesel Engine

2019 ◽  
pp. 1-9 ◽  
Author(s):  
P. Venkateswara Rao ◽  
S. Ramesh ◽  
S. Anil Kumar
Keyword(s):  
Diesel Engine ◽  
Diesel Fuel ◽  
Direct Injection ◽  
Primary Objective ◽  
Nox Emissions ◽  
Oxides Of Nitrogen ◽  
Smoke Emission ◽  
Oxygenated Additives ◽  
Blend Fuel ◽  
Fuel Formulation

The primary objective of this work is to reduce the particulate matter (PM) or smoke emission and oxides of nitrogen (NOx emissions) the two important harmful emissions and to increase the performance of diesel engine by using oxygenated additives with diesel as blend fuel. Formulation of available diesel fuel with additives is an advantage than considering of engine modification for improvement of higher output. From the available additives, three oxygenates are selected for experimentation by considering many aspects like cost, content of oxygen, flashpoint, solubility, seal etc. The selected oxygenates are Ethyl Aceto Acetate (EAA), Diethyl Carbonate (DEC), Diethylene Glycol (DEG). These oxygenates are blended with diesel fuel in proportions of 2.5%, 5% and 7.5% by volume and experiments were conducted on a single cylinder naturally aspirated direct injection diesel engine. From the results the conclusion are higher brake power and lower BSFC obtained for DEC blends at 7.5% of additive as compared to EAA, DEG and diesel at full load. In case of DEC blends the smoke emission is lower, whereas NOx emissions are very low in case of EAA additive blend fuels. The DEC can be considered is the best oxygenating additive to be blend with diesel in a proportion of 7.5% by volume.

scholarly journals Influence of Fuel Injection Pressure on the Emissions Characteristics and Engine Performance in a CRDI Diesel Engine Fueled with Palm Biodiesel Blends

Energies ◽  
2019 ◽  
Vol 12 (20) ◽  
pp. 3837 ◽  
Author(s):  
Sam Ki Yoon ◽  
Jun Cong Ge ◽  
Nag Jung Choi
Keyword(s):  
Diesel Engine ◽  
Diesel Fuel ◽  
Fuel Injection ◽  
Injection Pressure ◽  
Biodiesel Fuel ◽  
Nox Emissions ◽  
Oxides Of Nitrogen ◽  
Fuel Blend ◽  
Engine Load ◽  
Fuel Injection Pressure

This experiment investigates the combustion and emissions characteristics of a common rail direct injection (CRDI) diesel engine using various blends of pure diesel fuel and palm biodiesel. Fuel injection pressures of 45 and 65 MPa were investigated under engine loads of 50 and 100 Nm. The fuels studied herein were pure diesel fuel 100 vol.% with 0 vol.% of palm biodiesel (PBD0), pure diesel fuel 80 vol.% blended with 20 vol.% of palm biodiesel (PBD20), and pure diesel fuel 50 vol.% blended with 50 vol.% of palm biodiesel (PBD50). As the fuel injection pressure increased from 45 to 65 MPa under all engine loads, the combustion pressure and heat release rate also increased. The indicated mean effective pressure (IMEP) increased with an increase of the fuel injection pressure. In addition, for 50 Nm of the engine load, an increase to the fuel injection pressure resulted in a reduction of the brake specific fuel consumption (BSFC) by an average of 2.43%. In comparison, for an engine load of 100 Nm, an increase in the fuel injection pressure decreased BSFC by an average of 0.8%. Hydrocarbon (HC) and particulate matter (PM) decreased as fuel pressure increased, independent of the engine load. Increasing fuel injection pressure for 50 Nm engine load using PBD0, PBD20 and PBD50 decreased carbon monoxide (CO) emissions. When the fuel injection pressure was increased from 45 MPa to 65 MPa, oxides of nitrogen (NOx) emissions were increased for both engine loads. For a given fuel injection pressure, NOx emissions increased slightly as the biodiesel content in the fuel blend increased.

The Application of Non-Esterified Biodiesel in a Diesel Engine

2011 ◽  
Vol 110-116 ◽  
pp. 38-42
Author(s):  
Youngtaig Oh ◽  
Seung Hun Choi ◽  
Azjargal Janchiv
Keyword(s):  
Diesel Engine ◽  
Diesel Fuel ◽  
Alternative Energy ◽  
Direct Injection ◽  
Specific Energy Consumption ◽  
Energy Resource ◽  
Engine Performance ◽  
Smoke Emission ◽  
Exhaust Gas Emission ◽  
Water Dipole

Nowadays, various environmental regulations are being strengthened because of air pollution caused by exhaust gas emission of the automobiles. Biodiesel has been recognized as an alternative energy resource since it can be used without the modification of existing diesel engines and contains oxygen in itself, so the engine performance didn’t have large differences in comparison with the diesel fuel but remarkably reduces smoke emissions. The main objective of this study is to investigate usability of non-esterified biodiesel as an alternative fuel in a common rail direct injection diesel engine. The non-esterified biodiesel has not generated glycerin in esterificaion process and reduced the 20 percent of cost because it has not used methanol in the production process. Experiments were conducted by using the 5 percentage of biodiesel and 4 percentage of biodiesel with 1 percentage of WDP (water dipole power) in diesel fuel. Based on the experimental analysis the smoke emission of biodiesel was reduced significantly, but power, torque, and brake specific energy consumption was similar in comparison with commercial diesel fuel.

Low and High Purity Methanol Effect on Performance and Smoke Emission of Direct Injection Diesel Engine with Cooled EGR Fueled by Diesel Fuel and Jatropha Oil Blends

2014 ◽  
Vol 660 ◽  
pp. 426-430 ◽  
Author(s):  
Syaiful ◽  
Sobri ◽  
Nathanael P. Tandian
Keyword(s):  
Diesel Engine ◽  
Diesel Fuel ◽  
High Purity ◽  
Direct Injection ◽  
Jatropha Oil ◽  
Smoke Emission ◽  
Fuel Blend ◽  
Oil Blends ◽  
Fuel Blends ◽  
Oil Blend

The aim of this study is to experimentally investigate an effect of low and high purity methanol on a performance and smoke emission of diesel engine with cooled EGR system fueled by diesel fuel and jatropha oil blend. A four-stroke water cooled direct injection (DI) diesel engine with cooled EGR system was used in this work. The diesel engine was fueled by diesel fuel, jatropha oil and low (LPM) or high (HPM) purity methanol blends at the ratio of 100/0/0, 75/20/5, 70/20/10 and 65/20/15 % on volume basis respectively for the variation of engine loads in the range of 25 to 100% with 25% increments at 2000 rpm. Each load for every fuel blend was given by the 0% and 16.5% EGR rates. The results are found that the brake power for diesel engine fueled by diesel fuel, jatropha oil and LPM is approximately 8% lower than that of diesel engine fueled with the neat diesel, while it increases to 5.24% at the low load and reduces to 6.11% at the high load by injecting HPM in the fuel blends. At the same case, BSFC increases approximately 4.5% by injecting LPM in the fuel blends. The brake thermal efficiency rises approximately by 3.3% with LPM in the fuel blends, whereas it increases approximately 6% by injecting HPM. The smoke opacity reduces approximately by 70% with LPM or HPM in the fuel blends.

scholarly journals Performance and Emission analysis of Multi-Cylinder Common Rail Direct Injection Diesel Engine Powered with Blends of Tyre Pyrolysis Oil-Ethanol-Diesel

2021 ◽  
Author(s):  
Khandal S. V. ◽  
◽  
T.M. Yunus khan ◽  
Irfan Anjum Badruddin ◽  
Sarfaraz Kamangar ◽  
...  
Keyword(s):  
Diesel Fuel ◽  
Direct Injection ◽  
Common Rail ◽  
Pyrolysis Oil ◽  
Oxides Of Nitrogen ◽  
Smoke Emission ◽  
Emission Analysis ◽  
Performance And Emission ◽  
Ethanol Blends ◽  
Operation Results

This paper mainly focuses on optimal replacement of diesel by Tyre Pyrolysis oil-Ethanol blends to run a common rail direct injection (CRDI) multi cylinder engine and to compare the results with neat diesel fuel operation results at 1500 rpm. The engine was operated at different loads and speeds. From the experimental study, decrease in brake thermal efficiency (BTE) and oxides of nitrogen (NOx) emission with increase in carbon monoxide (CO), hydrocarbon (HC), and smoke emission was observed for blends as compared to diesel fuel. Further, it was also observed that increase in speed from 1200 rpm to 1800 rpm yielded higher BTE with decrease in CO, HC and smoke emission. But slightly increase in NOx, peak pressure (PP) and heat release rate (HRR) was reported at higher speed as compared to lower speeds. Beyond engine speed of 1800 rpm, knocking was observed.

STUDI PENENTUAN KOMPOSISI OPTIMUM CAMPURAN BAHAN BAKAR BIODIESEL–PETRODIESEL

2018 ◽  
Vol 4 (2) ◽  
Author(s):  
Soni S. Wirawan dkk
Keyword(s):  
Carbon Monoxide ◽  
Particulate Matter ◽  
Diesel Engine ◽  
Fuel Consumption ◽  
Diesel Fuel ◽  
Cetane Number ◽  
Price Policy ◽  
Oxides Of Nitrogen ◽  
Fuel Price ◽  
Biodiesel Blend

Biodiesel is a viable substitute for petroleum-based diesel fuel. Its advantages are improved lubricity, higher cetane number and cleaner emission. Biodiesel and its blends with petroleum-based diesel fuel can be used in diesel engines without any signifi cant modifi cations to the engines. Data from the numerous research reports and test programs showed that as the percent of biodiesel in blends increases, emission of hydrocarbons (HC), carbon monoxide (CO), and particulate matter (PM) all decrease, but the amount of oxides of nitrogen (NOx) and fuel consumption is tend to increase. The most signifi cant hurdle for broader commercialization of biodiesel is its cost. In current fuel price policy in Indonesia (especially fuel for transportation), the higher percent of biodiesel in blend will increase the price of blends fuel. The objective of this study is to assess the optimum blends of biodiesel with petroleum-based diesel fuel from the technically and economically consideration. The study result recommends that 20% biodiesel blend with 80% petroleum-based diesel fuel (B20) is the optimum blend for unmodifi ed diesel engine uses.Keywords: biodiesel, emission, optimum, blend

Explorative Investigation on Cashew Nut Shell Liquid Biodiesel blended with Ethanol and Hydrogen in Direct Injection (DI) Diesel Engine and prediction through Artificial Neural Network

2021 ◽  
Author(s):  
Thanigaivelan V ◽  
Lavanya R
Keyword(s):  
Diesel Engine ◽  
Diesel Fuel ◽  
Direct Injection ◽  
Cashew Nut Shell Liquid ◽  
Single Cylinder ◽  
Direct Injection Diesel Engine ◽  
Cashew Nut ◽  
Di Diesel Engine ◽  
Artificial Neural ◽  
Cashew Nut Shell

Abstract Emission from the DI diesel engine is series setback for environment viewpoint. Intended for that investigates for alternative biofuel is persuaded. The important hitches with the utilization of biofuels and their blends in DI diesel engines are higher emanations and inferior brake-thermal efficiency as associated to sole diesel fuel. In this effort, Cashew nut shell liquid (CNSL) biodiesel, hydrogen and ethanol (BHE) mixtures remained verified in a direct-injection diesel engine with single cylinder to examine the performance and discharge features of the engine. The ethanol remained supplemented 5%, 10% and 15% correspondingly through enhanced CNSL as well as hydrogen functioned twin fuel engine. The experiments done in a direct injection diesel engine with single-cylinder at steadystate conditions above the persistent RPM (1500RPM). Throughout the experiment, emissions of pollutants such as fuel consumption rate (SFC), hydrocarbons (HC), carbon monoxide (CO), nitrogen oxides (NOx) and pressure of the fuel were also measured. cylinders. The experimental results show that, compared to diesel fuel, the braking heat of the biodiesel mixture is reduced by 26.79-24% and the BSFC diminutions with growing addition of ethanol from the CNSL hydrogen mixture. The BTE upsurges thru a rise in ethanol proportion with CNSL hydrogen mixtures. Finally, the optimum combination of ethanol with CNSL hydrogen blends led to the reduced levels of HC and CO emissions with trivial upsurge in exhaust gas temperature and NOx emissions. This paper reconnoiters the routine of artificial neural networks (ANN) to envisage recital, ignition and discharges effect.

scholarly journals THE EFFECT OF DIESEL-BIODIESEL BLENDS ON THE PERFORMANCE AND EXHAUST EMISSIONS OF A DIRECT INJECTION OFF-ROAD DIESEL ENGINE

Transport ◽  
2014 ◽  
Vol 29 (4) ◽  
pp. 440-448 ◽  
Author(s):  
Tomas Mickevičius ◽  
Stasys Slavinskas ◽  
Slawomir Wierzbicki ◽  
Kamil Duda
Keyword(s):  
Diesel Engine ◽  
Diesel Fuel ◽  
Direct Injection ◽  
Engine Performance ◽  
Exhaust Emissions ◽  
Bench Test ◽  
Maximum Pressure ◽  
Cylinder Pressure ◽  
Biodiesel Blends ◽  
Performance And Emission

This paper presents a comparative analysis of the diesel engine performance and emission characteristics, when operating on diesel fuel and various diesel-biodiesel (B10, B20, B40, B60) blends, at various loads and engine speeds. The experimental tests were performed on a four-stroke, four-cylinder, direct injection, naturally aspirated, 60 kW diesel engine D-243. The in-cylinder pressure data was analysed to determine the ignition delay, the Heat Release Rate (HRR), maximum in-cylinder pressure and maximum pressure gradients. The influence of diesel-biodiesel blends on the Brake Specific Fuel Consumption (bsfc) and exhaust emissions was also investigated. The bench test results showed that when the engine running on blends B60 at full engine load and rated speed, the autoignition delay was 13.5% longer, in comparison with mineral diesel. Maximum cylinder pressure decreased about 1–2% when the amount of Rapeseed Methyl Ester (RME) expanded in the diesel fuel when operating at full load and 1400 min–1 speed. At rated mode, the minimum bsfc increased, when operating on biofuel blends compared to mineral diesel. The maximum brake thermal efficiency sustained at the levels from 0.3% to 6.5% lower in comparison with mineral diesel operating at full (100%) load. When the engine was running at maximum torque mode using diesel – RME fuel blends B10, B20, B40 and B60 the total emissions of nitrogen oxides decreased. At full and moderate load, the emission of carbon monoxide significantly raised as the amount of RME in fuel increased.

scholarly journals INVESTIGATION ON DIESEL ENGINE FUELLED BY MAHUA BIODIESEL

2021 ◽  
Vol 9 (1) ◽  
pp. 436-443
Author(s):  
M.Kannan, R.Balaji, R.T Sarath Babu, Chandrakant B. Shende, Ashish Selokar
Keyword(s):  
Diesel Engine ◽  
Engine Performance ◽  
Primary Objective ◽  
Injection Timing ◽  
Emission Characteristics ◽  
Oxides Of Nitrogen ◽  
Fuel Blend ◽  
Biodiesel Blends ◽  
Mahua Oil ◽  
Mahua Biodiesel

The primary objective of this study is to discover the effects of injection timing on performance, emission and combustion characteristics effect of advanced and retarded injection timing of the engine fuelled with mahua oil biodiesel blends. The engine performance, combustion and emission characteristics of the mahua oil biodiesel blends (B20, B40, B60, B80and B100) are investigated in this experimentation without any modification of the diesel engine. At this advanced pressure t he efficiency of engine by means of CO, Unburned HC gases and smoke emissions with higher oxides of nitrogen was observed compared to diesel. The obtained results are compared with a neat diesel and mahua oil biodiesel blends are shown through the graphs. From this study, identifies optimum fuel blend of this work. Thus, the combustion of duration is similar in all variance in pressure. This research paved a way to bio-diesel in mahua oil mixture and draws best outcome in emission less and to maintain eco-friendly environment.  

Effect of Cetane Number Improver on Emission Characteristics of Methanol/Diesel Blend Fuel

2012 ◽  
Vol 512-515 ◽  
pp. 1888-1891
Author(s):  
Jia Yi Du ◽  
Wei Xun Zhang ◽  
Deng Pan Zhang ◽  
Zhen Yu Sun
Keyword(s):  
Diesel Engine ◽  
Direct Injection ◽  
Cetane Number ◽  
Nox Emission ◽  
Fuel Load ◽  
Emission Characteristics ◽  
Soot Emission ◽  
Maximum Torque ◽  
Blend Fuel ◽  
Co Emission

The influence of cetane number improver on emission characteristics of diesel engine fueled with methanol/diesel blend fuel was investigated. Methanol/diesel blend fuel was prepared, in which the methanol content is 10%, different mass fraction (0%，0.5%) of cetane number improver were added to the blend fuel. Load characteristic experiments at maximum torque speed of the engine were carried out on 4B26 direct injection diesel engine. The results show that, compared with the engine fueled with diesel, the CO emission increases under low loads and reduces under medium and high loads, the HC emission increases, the NOx emission decreases under medium and low loads and increases under high loads, the soot emission reduces significantly when the diesel engine fueled with blends. When cetane number improver was added to blends, the CO and NOx emission reduces, the HC emission decreases, the soot emission increases to some extent compared with the methanol/dieselblend fuel without cetane number improver.

Sign in / Sign up

Export Citation Format

Share Document