scholarly journals Manufacture of Biogas from the Anaerobic Treatment of Cow Dung from Federal University of Technology, Owerri Livestock Farm

Author(s):  
O. E. Ugwu ◽  
J. U. Igbanny ◽  
T. S. Ademiju

Energy from hydrocarbon compounds has over the years been expensive and also played a part in negative health implications amongst others, for this reason alternative sources of energy have been sort for. In the quest for a healthier, more cost-effective energy, cow dung as a renewable source has been proven to be very efficient. This study investigated the manufacture of biogas using cow dung from School of Agriculture and Agricultural Technology (S.A.A.T) livestock farm located in Federal University of Technology, Owerri, Imo State, Nigeria. 25 kg of the cow dung was used in this study. The digestion was carried out in a 50L anaerobic digester at a temperature of 30°C - 36°C and uncontrolled pH for a period of 40 days. The average quantity of biogas produced through the period was 10.39 liters, representing 46% of the total biogas production. The average temperature was 33.0°C. The utilization of cow dung as fuel will also help in the management of waste within the livestock farm. As an eco-friendly source of energy, the biomass generated after digestion can be utilized to improve soil fertility.

2021 ◽  
Vol 15 (3) ◽  
pp. 302-311
Author(s):  
Jingping Dai ◽  
Jiang Li ◽  
Wang Zhifang ◽  
Xie Yuqing ◽  
Wang Xiaou ◽  
...  

To fill the gap between the rise in demand for energy and decline in the traditional energy sources such as coal, natural gas and nuclear energy, other alternative sources such as biogas are necessary. Studies have shown that the existing conditions within the fermentation realm control the microbial characteristics in biogas production. However, there is inadequate insight between the duration of fermentation and the microbial diversity, and with specific emphasis to cow manure as the substrate under low temperature fermentation. This study aimed at providing additional insight on the effect of varying fermentation duration (0 to 60 days) on the composition of the dominant microbial flora on cow dung based low-temperature (15 °C) biogas fermentation using metagenomics and metabolomics analyses approach. The study results showed that the main dominant community in the process of methanogenesis are the Spirochaetae, Synergistetes and Chloroflexi, and are new flora in the methane phase. In the peak stage of low-temperature biogas fermentation, the dominant bacteria groups were Methanosarcina and after adding 10% concentration of L1 bacteria. The prediction of metabolic pathway was mainly carbohydrate metabolism and amino acid metabolism with succinyl-CoA synthase a subunit, lactaldehyde reductase and the glutamate-glyoxylate aminotransferase being the main unique enzymes. The study therefore supports the potential of involving the reported dominant microbial communities and related enzymatic activities for improved biogas production under low temperature conditions.


2019 ◽  
Vol 41 (4) ◽  
pp. 563-563
Author(s):  
Muhammad Sohail Bashir Muhammad Sohail Bashir ◽  
Aqsa Safdar Aqsa Safdar ◽  
Shoaib Zaheer Shoaib Zaheer ◽  
Abdul Rehman Farooqi Abdul Rehman Farooqi ◽  
Muhammad Jamil Muhammad Jamil

Household kitchen waste quantity is increasing rapidly because of the population explosion. Agricultural growth and intensive animal farming are generating a large quantity of bio waste. Disposing of this huge amount of waste is a serious environmental issue of the world. This waste can be used as an alternative source for the generation of green fuel by converting it to biogas. Though, a lot of work has been done on biogas production from conventional feedstock. However, it is highly desired to improve and optimize the process with kitchen waste used as feedstock. In this paper, cost-effective, environmentally friendly and high-quality biogas is produced by anaerobic digestion of kitchen waste mixture with inoculum. Inoculum is used as a source of microbial population. It is prepared by mixing of cow dung and water with a weight ratio of 1:5. The effect of temperature, pH, and the weight ratio of inoculum/kitchen waste on the production of biogas has been studied. The results indicated that the optimum pH value is 7.5 and for the maximum production of biogas temperature should be 37 ˚C. The optimum weight ratio of inoculum/kitchen waste is 60/40. The quality of biogas is improved by the absorption of CO2 from it with the aid of absorber contains 2 M solution of NaOH. The gas was burnt smoothly with a blue flame. This indicates the high content of CH4 in biogas. It is a green heating and cooking fuel and can be used for transport and power generation.


2012 ◽  
Vol 11 (4) ◽  
pp. 849-856 ◽  
Author(s):  
Alvydas Zagorskis ◽  
Pranas Baltrenas ◽  
Antonas Misevicius ◽  
Edita Baltrenaite

2020 ◽  
Vol 6 (3) ◽  
pp. 180-191
Author(s):  
Kavitha Chandrasekaran

Background:: In the long run, synthetic tints were found to be harmful to the chemicals. As a result natural tints have come to be used for their many intrinsic values. The main reason being, then availability of local plants as the main source of natural colorants. Their easy availability in the country being zero cost – effective and planted for other purposes are the main reasons for utilizing them as natural tints. Almost all the parts of the plants, namely stem, leaves, fruits, seeds, barks etc. are used for extracting natural colour. In addition, they are antimicrobial antifungal, insect – repellant deodorant, disinfectant having medicinal values. Methods:: Sweet Indrajao leaves were cleaned by washing with water and dried under direct sunlight and ground as fine powder. A fine strainer was used to remove the wastages. After all these processes, 1-kilogram leaves weighed 318 grams. Then, it is put in 75% ethanol 25% water and heated in a breaker which in kept over a water bath for 2 hours. After this, the contents were filtered and kept in a separate beaker. Bleached fleece draperies stained with stain extract were made to become wet and put into different stain baths which contain the required amount of stain extract and water. Acetic acid was added to it after 20 minutes. The fleece drapery was stained for about one hour at 60oC. The draperies thus stained were removed, squeezed, and put to treatment with metal salts without washing. Different metal salts were used for the treatment using 3% of any one of the chemical mordants like alum, stannous chloride, potassium dichromate, ferrous sulphate, nickel sulphate, copper sulphate and natural mordants such as myrobolan, turmeric, cow dung, Banana sap juice at 60oC for 30 minutes with MLR of 1:30. The stained draperies were washed repeatedly in all the three methods in water and dried in air. At last, the stained draperies were put to soap with soap solution at 60oC for 10 minutes. The draperies were repeatedly washed in water and dried under the sun. Results:: Sweet Indrajao leaves discharged colour easily in alcoholic water. The fleece draperies were stained with chemical and natural mordants. It was observed that the stain uptake was found to be good in post-mordanting method. Ultrasonication has clearly improved the stainability of the draperies at pH 3 and 3.5 values. The pH decreases the stain ability under both Conventional and Ultrasonic conditions. The colour strength increases with an increase in staining temperature in both cases of US and CH methods. Conclusion:: Sweet Indrajao.L has been found to have good ultrasonic potential as a stain plant. The stain uptake as well as the fastness properties of the fleece drapery were found to enhance when metal mordant was used in conjugation with ultra-sonication for the extract of Sweet Indrajao. It was also found that the enhancement of staining ability was better without mordant draperies. The dye extract showed good antibacterial activity against the three bacterial pathogens. Among the three bacterial pathogens, dye extract showed more effective against Escherichia coli pathogens and dye extract showed more effective against Aspergillus pathogens. Hence, the ultrasonic method of drapery staining may be appropriate and beneficial for society at large in future.


Polymers ◽  
2021 ◽  
Vol 13 (13) ◽  
pp. 2217
Author(s):  
Daniela Șova ◽  
Mariana Domnica Stanciu ◽  
Sergiu Valeriu Georgescu

Investigating the large number of various materials now available, some materials scientists promoted a method of combining existing materials with geometric features. By studying natural materials, the performance of simple constituent materials is improved by manipulating their internal geometry; as such, any base material can be used by performing millimeter-scale air channels. The porous structure obtained utilizes the low thermal conductivity of the gas in the pores. At the same time, heat radiation and gas convection is hindered by the solid structure. The solution that was proposed in this research for obtaining a material with porous structure consisted in perforating extruded polystyrene (XPS) panels, as base material. Perforation was performed horizontally and at an angle of 45 degrees related to the face panel. The method is simple and cost-effective. Perforated and simple XPS panels were subjected to three different temperature regimes in order to measure the thermal conductivity. There was an increase in thermal conductivity with the increase in average temperature in all studied cases. The presence of air channels reduced the thermal conductivity of the perforated panels. The reduction was more significant at the panels with inclined channels. The differences between the thermal conductivity of simple XPS and perforated XPS panels are small, but the latter can be improved by increasing the number of channels and the air channels’ diameter. Additionally, the higher the thermal conductivity of the base material, the more significant is the presence of the channels, reducing the effective thermal conductivity. A base material with low emissivity may also reduce the thermal conductivity.


2001 ◽  
Vol 44 (8) ◽  
pp. 15-25 ◽  
Author(s):  
J.B. van Lier ◽  
F.P. van der Zee ◽  
N.C.G. Tan ◽  
S. Rebac ◽  
R. Kleerebezem

Anaerobic wastewater treatment (AnWT) is considered as the most cost-effective solution for organically polluted industrial waste streams. Particularly the development of high-rate systems, in which hydraulic retention times are uncoupled from solids retention times, has led to a world-wide acceptance of AnWT. In the last decade up to the present, the application potentials of AnWT are further explored. Research shows the feasibility of anaerobic reactors under extreme conditions, such as low and high temperatures. Also toxic and/or recalcitrant wastewaters, that were previously believed not to be suitable for anaerobic processes, are now effectively treated. The recent advances are made possible by adapting the conventional anaerobic high-rate concept to the more extreme conditions. Staged anaerobic reactor concepts show advantages under non-optimal temperature conditions as well as during the treatment of chemical wastewater. In other situations, a staged anaerobic - aerobic approach is required for biodegradation of specific pollutants, e.g. the removal of dyes from textile processing wastewaters. The current paper illustrates the benefits of reactor staging and the yet un-exploited potentials of high-rate AnWT.


2018 ◽  
Vol 78 (9) ◽  
pp. 1916-1924 ◽  
Author(s):  
Lucie Pokorna-Krayzelova ◽  
Dana Vejmelková ◽  
Lara Selan ◽  
Pavel Jenicek ◽  
Eveline I. P. Volcke ◽  
...  

Abstract Hydrogen sulfide is a toxic and usually undesirable by-product of the anaerobic treatment of sulfate-containing wastewater. It can be removed through microaeration, a simple and cost-effective method involving the application of oxygen-limiting conditions (i.e., dissolved oxygen below 0.1 mg L−1). However, the exact transformation pathways of sulfide under microaerobic conditions are still unclear. In this paper, batch experiments were performed to study biochemical and chemical sulfide oxidation under microaerobic conditions. The biochemical experiments were conducted using a strain of Sulfuricurvum kujiense. Under microaerobic conditions, the biochemical sulfide oxidation rate (in mg S L−1 d−1) was approximately 2.5 times faster than the chemical sulfide oxidation rate. Elemental sulfur was the major end-product of both biochemical and chemical sulfide oxidation. During biochemical sulfide oxidation elemental sulfur was in the form of white flakes, while during chemical sulfide oxidation elemental sulfur created a white suspension. Moreover, a mathematical model describing biochemical and chemical sulfide oxidation was developed and calibrated by the experimental results.


2001 ◽  
Vol 44 (6) ◽  
pp. 141-147 ◽  
Author(s):  
R. Saravanane ◽  
D. V.S. Murthy ◽  
K. Krishnaiah

Starch manufacturing industrial units, such as sago mills, both at medium and large scale, suffer from inadequate treatment and disposal problems due to high concentration of suspended solid content present in the effluent. In order to investigate the viability of treatment of sago effluent, a laboratory scale study was conducted. The treatment of sago effluent was studied in a continuous flow anaerobic fluidized bed reactor. The start-up of the reactor was carried out using a mixture of digested supernatant sewage sludge and cow dung slurry in different proportions. The effect of operating variables such as COD of the effluent, bed expansion, minimum fluidization velocity on efficiency of treatment and recovery of biogas was investigated. The treated wastewater was analysed for recycling and reuse to ensure an alternative for sustainable water resourse management. The maximum efficiency of treatment was found to be 82% and the nitrogen enriched digested sludge was recommended for agricultural use.


2002 ◽  
Vol 45 (10) ◽  
pp. 321-328 ◽  
Author(s):  
H.J. Gijzen

After the discovery of methane gas by Alessandro Volta in 1776, it took about 100 years before anaerobic processes for the treatment of wastewater and sludges were introduced. The development of high rate anaerobic digesters for the treatment of sewage and industrial wastewater took until the nineteen-seventies and for solid waste even till the nineteen-eighties. All digesters have in common that they apply natural anaerobic consortia of microorganisms for degradation and transformation processes. In view of this, it could be rewarding to evaluate the efficiency of natural ecosystems for their possible application. Examples of high rate anaerobic natural systems include the forestomach of ruminants and the hindgut of certain insects, such as termites and cockroaches. These “natural reactors” exhibit volumetric methane production rates as high as 35 l/l.d. The development of anaerobic reactors based on such natural anaerobic systems could produce eco-technologies for the effective management of a wide variety of solid wastes and industrial wastewater. Important limitations of anaerobic treatment of domestic sewage relate to the absence of nutrient and pathogen removal. A combination of anaerobic pre-treatment followed by photosynthetic post-treatment is proposed for the effective recovery of energy and nutrients from sewage. This eco-technology approach is based on the recognition that the main nutrient assimilating capacity is housed in photosynthetic plants. The proposed anaerobic-photosynthetic process is energy efficient, cost effective and applicable under a wide variety of rural and urban conditions. In conclusion: a natural systems approach towards waste management could generate affordable eco-technologies for effective treatment and resource recovery.


Sign in / Sign up

Export Citation Format

Share Document