Investigation of Pressed Solid Biofuel Produced from Multi-Crop Biomass

The paper presents the preparation and use of pressed solid biofuel of multi-crop plants (fibrous hemp (Cannabis sativa L.), maize (Zea mays L.) and faba bean (Vicia faba L.)) as mono, binary and trinomial crops. The results of the investigation show that three main chemical elements (carbon, oxygen and hydrogen) accounted for 93.1 to 94.9% of the biomass pellet content. The moisture content varied from 3.9 to 8.8%, ash content from 4.5 to 6.8% and calorific value from 16.8 to 17.1 MJ·kg−1. It was found that the density (DM) of all variants of pellets was very similar; the faba bean biomass pellets had the highest density of 1195.8 kg·m−3 DM. The initial ash deformation temperature (DT) of burning biomass pellets was detected, which varied from 976 to 1322 °C. High potassium (K), calcium (Ca) and phosphorus (P) concentrations were found in all types of biomass ash. The quantities of heavy metals in pellet ash were not large and did not exceed the permissible values according to Lithuanian legislation. These chemical properties of multi-crop biomass ash allow them to be used in agriculture for plant fertilization.

A New System of Sustainable Silico-Aluminous and Silicate Materials for Cultivation Purpose within Sustainable Buildings: Chemical-Physical, Antibacterial and Cytotoxicity Properties

In this study, we compared the chemical-physical, antibacterial, and cytotoxicity properties of silico-aluminous and silicate materials for outdoor (green roof, planted walls) and indoor (urban farms, indoor microgreen gardens) cultivation purpose in a context of sustainable construction. Glasses and lightweight aggregates were tailored starting from waste, by-product, and post-consumer and bioproducts (packaging glass cullet, cattle bone flour ash, vegetable biomass ash, spent coffee ground, degreased from biomass of prepupae of Black Soldier Flies) mixed together with a national ferruginous red clay, quarry scrap pumice and, if necessary, with K2CO3 of reagent grade. The first type of material was obtained by melting at 1200 °C and the second one by powder sintering at 1000 °C. All specimens, subjected to antibacterial test, showed both low zone of inhibitions towards two Gram-negative and two Gram-positive bacterial strains. A cytotoxicity test on mouse embryonic fibroblast NIH-3T3 cell line directly exposed to the investigated materials was performed at three different exposure times (1 h, 3 h, and 6 h). Data acquired highlighted that the materials positively affected redox mitochondrial activity of the fibroblast cells. The concentrations of leachate heavy metals detected on selected materials in water at room temperature after 24 h were lower than the European law limit and an interesting release of P, K, and N nutrients was noted for those formulations designed for agronomic purposes. pH, falling on average within the 6.5–7.5 range, is optimal for most crops, and the specific conductivity <2 dS/m indicates no depression danger for crops. Both bulk density <1200 kg/m3 and porosity over 50% seem to ensure good performance of lightening, drainage, water reservation, and oxygenation of the roots.

Ash Melting Behavior of Rice Straw and Calcium Additives

Rice straw is potentially an appropriate feedstock material for biofuel production, since a huge amount of this postharvest residue is generated every year. The transformation of such agricultural biomass into densified products with a higher energy value and their subsequent combustion is associated with several questions. One of them is that rice straw exhibits a large formation of ash during combustion; thus, it is essential to know the nature of its ash melting behavior. Generally, during the combustion of straw biomass, ash sintering occurs in relatively low temperatures, resulting in the damaging of heating equipment. This negative aspect can be overcome by the addition of calcium-based additives. This paper aimed to study the ash melting behavior at a laboratory scale and to determine the ash melting points of rice straw mixed with calcium carbonate (CaCO3) and calcium hydroxide (Ca(OH)2) in different proportional ratios. The standardly produced ash samples from the rice straw obtained from Cambodia were constantly heated up in a muffle furnace, and characteristic temperatures of ash melting, i.e., shrinkage, deformation, hemisphere, and flow temperature, were recorded. The results showed that increasing the additive ratio did not bring linear growth of the melting temperatures. The addition of 1% CaCO3 showed an optimal positive impact of higher ash melting temperatures, and thus a better ability to abate the sintering of the rice straw ash.

Power-Based Estimation of Cutting Forces During Turning of Aluminium Biomass Ash Particulate Composite

Aluminum-Biomass Ash Particulate Composite is a reinforced composite material of aluminum and biomass ash particles. The composite offers significant mechanical properties advantage and low-cost advantage because of the use of waste as the reinforcement material and as a result, it is gaining increased industrial attention because of the many advantages they offer over conventional Aluminium Matrix Composites. These materials are mostly accessed on the basis of their mechanical, microstructural and chemical properties with very limited interest on their machinability relative to the base material. The specific cutting force coefficients and cutting forces of the composite were estimated during CNC turning operations and the effects of reinforcement on the machinability responses were studied. In this work, power-based force estimation approach was adopted for this purpose for the first time. This approach is less expensive compared to the dynamometric approach since it relies on adapting existing equipment developed for other purposes. This was done by measuring the electric power of the direct-drive motors of the CNC machine during the turning process and the power measurements were analyzed to obtain the force coefficients. The cutting force components were observed to decrease as the percentage rice husk ash (RHA) reinforcement increased. This agrees with known results for the composite based on the dynamometric approach. Since the cutting force components decrease with increase in reinforcement, it can be deduced that increasing RHA in the Aluminium might reduce friction at the tool-chip interface and extend tool life, in other words, improving machinability. The composite therefore promises to be more cost effective than the base material in machinability terms.

Experimental Investigation of the Ash Deposition Characteristics of Biomass Pretreated by Ash Removal during Co-Combustion with Sub-Bituminous Coal

Although replacing biomass, (e.g., wood chips and pellets), with thinning wood and herbaceous biomass is eco-friendly and economically advantageous, their direct utilization in plant boilers is associated with ash-related challenges, including slagging and fouling. The aim of this study is to determine the effects of ash removal treatment (ashless biomass (ALB)) in the context of solid fuel power plant boilers. Ash was removed via neutralization of metal ions and carboxylic acids contained in the biomass ash. The ash removal rate of K, Na, Cl was indicated by assessing the total biomass before and after ash removal treatment, via XRF analysis. Co-combustion with sub-bituminous coal and ALB-treated biomass was analyzed using a drop tube furnace and revealed that NOx and SOx values converged converge toward an approximate 10 ppm error, whereas the Unburned Carbon (UBC) data did not exhibit a specific trend. Factors associated with slagging and fouling, (capture efficiency (CE), and energy based growth rate (GRE)) were calculated. All biomass samples without pretreatment exhibited V-shaped variation. Conversely, for ashless biomass (ALB) samples, CE and GRE gradually decreased. Thus, the ALB technique may minimize slagging and fouling in a boiler, thus, reducing internal corrosion associated with ash deposition and enhancing the economic operation of boilers.