Ultra-low threshold lasing through phase front engineering via a metallic circular aperture

Semiconductor lasers with extremely low threshold power require a combination of small volume active region with high-quality-factor cavities. For ridge lasers with highly reflective coatings, an ultra-low threshold demands significantly suppressing the diffraction loss at the facets of the laser. Here, we demonstrate that introducing a subwavelength aperture in the metallic highly reflective coating of a laser can correct the phase front, thereby counter-intuitively enhancing both its modal reflectivity and transmissivity at the same time. Theoretical and experimental results manifest a decreasing in the mirror loss by over 40% and an increasing in the transmissivity by 104. Implementing this method on a small-cavity quantum cascade laser, room-temperature continuous-wave lasing operation at 4.5 μm wavelength with an electrical consumption power of only 143 mW is achieved. Our work suggests possibilities for future portable applications and can be implemented in a broad range of optoelectronic systems.

Lab-Controlled Experimental Evaluation of Heat-Reflective Coatings by Increasing Surface Albedo for Cool Pavements in Urban Areas

Many studies were conducted to find possible strategies for reducing the urban heat island (UHI) effect during the hot summer months. One of the largest contributors to UHI is the role that paved surfaces play in the warming of urban areas. Solar-reflective cool pavements stay cooler in the sun than traditional pavements. Pavement reflectance can be enhanced by using a reflective surface coating. The use of heat-reflective coatings to combat the effects of pavements on UHI was previously studied but no consistent conclusions were drawn. To find a conclusive solution, this work focuses on the abilities of heat-reflective pavement coatings to reduce UHI in varying weather conditions. Within this context, both concrete and asphalt samples were subject to a series of performance tests when applied to a heat-reflective coating, under the influence of normal, windy, and humid conditions. During these tests, the samples were heated with a halogen lamp and the surface temperature profile was measured using an infrared thermal camera. The air temperature was recorded with a thermometer, and the body temperature at multiple depths of the samples was measured using thermocouples. The results from these tests show that the effectiveness of the heat-reflective coating varies under different weather conditions. For instance, the coated samples were about 1 °C cooler for concrete and nearly 5 °C cooler for asphalt, on average. However, this temperature difference was reduced significantly under windy conditions. As such, the findings from this work conclude that the heat-reflective coatings can effectively cool down the pavement by increasing the surface albedo, and thus might be a viable solution to mitigate UHI impacts in the city/urban areas.

Synthesis and Applications of Functional Nanomaterials

The unique physical and chemical properties and variable application potential of nanomaterials are continuously devoted to stimulating scientists’ studying enthusiasm. Extremely fine grains bring quantities excellent properties such as low density, low elastic modulus, high resistance and low thermal conductivity to nanomaterials, which has extensive use in the photoelectric field, environment, bioengineering and other fields. The research progress of graphene quantum dots, transparent reflective coatings and self-assembled nanotubes are mainly demonstrated. This paper shows the role of graphene quantum dots in solar cells, summarizes the synthesis methods of self-assembled nanotubes and their applications in bioengineering, and describes the development of transparent thermal reflective coatings for energy-saving glass attributed to providing relevant reference and basis for the development and research of nanomaterials.

Multilayer Reflective Coatings for BEUV Lithography: A Review

The development of microelectronics is always driven by reducing transistor size and increasing integration, from the initial micron-scale to the current few nanometers. The photolithography technique for manufacturing the transistor needs to reduce the wavelength of the optical wave, from ultraviolet to the extreme ultraviolet radiation. One approach toward decreasing the working wavelength is using lithography based on beyond extreme ultraviolet radiation (BEUV) with a wavelength around 7 nm. The BEUV lithography relies on advanced reflective optics such as periodic multilayer film X-ray mirrors (PMMs). PMMs are artificial Bragg crystals having alternate layers of “light” and “heavy” materials. The periodicity of such a structure is relatively half of the working wavelength. Because a BEUV lithographical system contains at least 10 mirrors, the optics’ reflectivity becomes a crucial point. The increasing of a single mirror’s reflectivity by 10% will increase the system’s overall throughput six-fold. In this work, the properties and development status of PMMs, particularly for BEUV lithography, were reviewed to gain a better understanding of their advantages and limitations. Emphasis was given to materials, design concepts, structure, deposition method, and optical characteristics of these coatings.

Multilayer Reflective Coatings for BEUV Lithography: A Review

The development of microelectronics is always driven by reducing transistor size and increasing integration, from the initial micron-scale to the current few nanometers. The photolithography technique for manufacturing the transistor needs to reduce the wavelength of the optical wave, from ultraviolet, deep, to the existing extreme ultraviolet light. One approach toward decreasing the working wavelength is using lithography based on beyond extreme ultraviolet radiation (BEUV) with a wavelength around 7 nm. The BEUV lithography relies on advanced reflective optics such as periodic multilayer film X-ray mirrors (PMMs). PMMs are artificial Bragg crystals having alternate layers of “light” and “heavy” materials. The periodicity of such a structure is relatively half of the working wavelength. Since a BEUV lithographical system contains at least 10 mirrors, optics’ reflectivity becomes a crucial point. The increasing of a single mirror's reflectivity by 10% will increase the system’s overall throughput by 6 times. In this work, the properties and development status of PMMs, particularly for BEUV lithography, were reviewed to gain a better understanding of their advantages and limitations. Emphasis was given to materials, design concepts, structure, deposition method, and optical characteristics of these coatings.

Nanopatterned Polymer Molds Using Anodized Aluminum Templates for Anti-Reflective Coatings

This work introduces a facile geometry-controlled method for the fabrication of embossed and engraved polymeric moth-eye-inspired nanostructures in imprinting molds using anodic aluminum oxide (AAO) templates, resulting in a novel anti-reflective transparent coating. The moth-eye nanostructures are prepared directly on the surface of a flexible polyethylene terephthalate (PET) substrate. As a prerequisite procedure, a UV-curable polyurethane acrylate resin is spun on the PET. The shape of the moth-eye nanostructures can then be adjusted by controlling the size and shape of the nanopores in the AAO templates. Both embossed and concaved polymer moth-eye nanostructures were successfully mounted on a PET substrate. Embossed polymer replica molds were prepared using the AAO master templates in combination with an imprinting process. As revealed by field-emission electron microscope (FE-SEM) images, conical nanopatterns in the AAO template with a diameter of ~90 nm and a depth of ~100 nm, create a homogeneous embossed morphology in the polymer moth-eye nanostructure. The polymeric molds with the depths of 300 and 500 nm revealed the amalgamated structures in their apexes. In addition, a dip-imprinting process of the polymeric layers was implemented to yield a concaved mold by assembly on the surface of the 100 nm embossed polymer mold substrate. Considering that the embossed structures may be crumbled due to their protuberant shapes, the concaved geometries can have an advantage of stability in a certain application concerning physical degradation along with a higher transmission by ~2%, despite somewhat nonuniform structure. The experimental and theoretical results of this study indicate that this polymer layer has the potential for use in anti-reflective coating applications in transparent films.

Simulation of Perovskite Solar Cells Optimized by the Inverse Planar Method in SILVACO: 3D Electrical and Optical Models

In recent years, perovskite solar cells (PSCs), often referred to as the third generation, have rapidly proliferated. Their most prominent deficiencies are their low efficiency and poor stability. To enhance their productivity, a combination of silicon and perovskite is employed. Here, we present a 3D simulation analysis of various electrical and optical properties of PSCs using the SILVACO simulation software. Using the inverted planar method with inorganic transport materials and the proper selection of anti-reflective coatings with a back contact layer increases the efficiency of PSCs to 28.064%, and enhances their stability without using silicone composites. Several materials, including CaF2, SiO2, and Al2O3, with various thicknesses have been employed to investigate the effect of anti-reflective coatings, and to improve the efficiency of the simulated PSC. The best thickness of the absorbent layer is 500 nm, using a CaF2 anti-reflective coating with an optimal thickness of 110 nm. A polymer composition of Spiro-OMeTAD and inorganic materials Cu2O and NiOx was used as the hole transport material (HTM) and inorganic ZnO was employed as the electron transport material (ETM) to optimize the solar cell efficiency, and an optimized thickness was considered for these materials. Yields of 29.261, 28.064 and 27.325% were obtained for Spiro-OMeTAD/ZnO, Cu2O/ZnO and NiOx/ZnO, respectively. Thus, Spiro-OMeTAD yields the highest efficiency. This material is highly expensive with a complex synthesis and high degradability. We proposed to employ Cu2O to alleviate these problems; however, this reduces the efficiency by 1.197%. As a graphene connector has high flexibility, reduces cell weight, and is cheaper and more accessible compared to other metals, it was regarded as an optimal alternative. The simulation results indicate that using the inverted planar method with inorganic transport materials for graphene-based PSCs is highly promising.