Accurate THz Ellipsometry Using Calibration in Time Domain

We report on the realisation of a customized THz Time Domain Spectroscopic Ellipsometer (THz-TDSE) based on fiber-coupled photoconductive antennas, operating in a wide range of incident angles and allowing also standard transmission spectroscopy without any optical realignment. To ensure accurate parameter extraction for a broad range of materials, we developed a fast and effective algorithm-assisted method to calibrate the setup and compensate for the nonideality in the response of the THz system. The procedure allows to minimise errors induced by imperfect response of the antennas and polarizers, imprecise setting of the impinging and receiving angles in the goniometric mechanical arms, and unavoidable mismatches in the THz beam optics. Differently from other calibration methods applied in the literature, our approach compares in time domain the ellipsometric derived electric field s- and p-polarised components at a given angle of incidence with the reconstructed ones, attained by using the complex dielectric function of a known sample. The calibrated response is determined with high precision by setting the system in transmission mode. In order to validate the technique, ellipsometric measurements have been carried out at various angle of incidences on a number of materials both in solid and liquid form, and their data compared with what obtained by conventional THz spectroscopy. Results show that THz-TDSE accompanied with an accurate calibration procedure is an effective technique for material characterization, especially in case of samples with a high absorption rate that are not easily investigated through transmission measurements.

Concrete anisotropy estimated from ultrasonic signal amplitudes

The anisotropy of concrete is an essential issue in the construction industry. In this study, for the first time, ultrasonic compression and shear wave signals have been investigated for the orthogonal directions of unreinforced concrete by means of fast Fourier transformation (FFT). For this purpose, cubic concrete samples were prepared in 12 designs of different strengths for ultrasound transmission measurements. The characteristic amplitudes at dominant frequencies were determined by the FFT of these signals. The FFT amplitude differences in the compression and the shear wave signals on the orthogonally oriented surfaces provide essential information about the presence and degree of anisotropy. According to linear regression analysis, the FFT amplitude anisotropies and the amplitude ratios of the compression and shear waves decreased significantly according to increasing concrete strength. In addition, it was found that the anisotropy and the ratio of the FFT amplitudes increased proportionally to the water/cement ratio, the porosity and the water content of the various concrete designs.

Evolving contact mechanics and microstructure formation dynamics of the lithium metal-Li7La3Zr2O12 interface

The dynamic behavior of the interface between the lithium metal electrode and a solid-state electrolyte plays a critical role in all-solid-state battery performance. The evolution of this interface throughout cycling involves multiscale mechanical and chemical heterogeneity at the micro- and nano-scale. These features are dependent on operating conditions such as current density and stack pressure. Here we report the coupling of operando acoustic transmission measurements with nuclear magnetic resonance spectroscopy and magnetic resonance imaging to correlate changes in interfacial mechanics (such as contact loss and crack formation) with the growth of lithium microstructures during cell cycling. Together, the techniques reveal the chemo-mechanical behavior that governs lithium metal and Li7La3Zr2O12 interfacial dynamics at various stack pressure regimes and with voltage polarization.

Evaluation of MEMS NIR Spectrometers for On-Farm Analysis of Raw Milk Composition

Today, measurement of raw milk quality and composition relies on Fourier transform infrared spectroscopy to monitor and improve dairy production and cow health. However, these laboratory analyzers are bulky, expensive and can only be used by experts. Moreover, the sample logistics and data transfer delay the information on product quality, and the measures taken to optimize the care and feeding of the cattle render them less suitable for real-time monitoring. An on-farm spectrometer with compact size and affordable cost could bring a solution for this discrepancy. This paper evaluates the performance of microelectromechanical system (MEMS)-based near-infrared (NIR) spectrometers as on-farm milk analyzers. These spectrometers use Fabry–Pérot interferometers for wavelength tuning, giving them the advantage of very compact size and affordable price. This study discusses the ability of MEMS spectrometers to reach the accuracy limits set by the International Committee for Animal Recording (ICAR) for at-line analyzers of the milk content regarding fat, protein and lactose. According to the achieved results, the transmission measurements with the NIRONE 2.5 spectrometer perform best, with an acceptable root mean squared error of prediction (RMSEP = 0.21% w/w) for the measurement of milk fat and excellent performance (RMSEP ≤ 0.11% w/w) for protein and lactose. In addition, the transmission measurements using the NIRONE 2.0 module give similar results for fat and lactose (RMSEP of 0.21 and 0.10% w/w respectively), while the prediction of protein is slightly deteriorated (RMSEP = 0.15% w/w). These results show that the MEMS spectrometers can reach sufficient prediction accuracy compared to ICAR standard values for at-line and in-line fat, protein and lactose prediction.

Effect of Liquid Crystalline Host on Structural Changes in Magnetosomes Based Ferronematics

The effect of the liquid crystalline host on structural changes in magnetosomes based on ferronematics is studied using the surface acoustic wave (SAW) technique supported by some capacitance and light transmission measurements. The measurement of the attenuation response of SAW propagating along the interface between LC and the piezoelectric substrate is used to study processes of structural changes under magnetic field. The magnetosome nanoparticles of the same volume concentration were added to three different nematic LCs, 5CB, 6CB, and E7. Unlike to undoped LCs, the different responses of SAW attenuation under the influence of magnetic and electric fields in LCs doped with magnetosomes were observed due to characteristic structural changes. The decrease of the threshold field for doped LCs as compared with pure LCs and slight effects on structural changes were registered. The threshold magnetic fields of LCs and composites were determined from capacitance measurements, and the slight shift to lower values was registered for doped LCs. The shift of nematic-isotropic transition was registered from dependencies of SAW attenuation on temperature. The acoustic anisotropy measurement approved the previous supposition about the role of bulk viscosity in used SAW measurements. In addition, capacitance and light transmition investigations supported SAW results and pointed out conclusions about their magnetic field behavior. Obtained results are discussed and confronted with previous ones and coincide well with those observed using acoustic, optical, or dielectric techniques.

Polyester Fabric With Fluorescent Properties Using Microwave Technology For Anti-Counterfeiting Applications

The article presented concerns the application of fluorescein as a fluorescent material for anti-counterfeiting technology which will allow the labeling and identification of legitimate articles in the textile field. Fluorescein has been applied to polyester fabrics by microwave irradiation technique in the presence of a UV absorber. Thus, its presence in the textile substrate is detectable following an excitation at a specific wavelength belonging to the Ultra-violet zone, which makes this material very effective for tracking and detecting counterfeit articles. Fluorescent samples are characterized morphologically by scanning electron microscopy (SEM) and quantitatively by optical spectroscopy such as reflectance and transmission measurements. The treated samples show under UV light a yellowish green emission with a slight yellow coloration of the polyester fiber. The UV absorber applied to the fluorescent solution improves the light resistance of the treated samples by 25%. Their addition to the bath can also ensure the production of a protective fabric against UV.

Cataract Development by Exposure to Ultraviolet and Blue Visible Light in Porcine Lenses

Background and Objectives: Cataract is still the leading cause of blindness. Its development is well researched for UV radiation. Modern light sources like LEDs and displays tend to emit blue light. The effect of blue light on the retina is called blue light hazard and is studied extensively. However, its impact on the lens is not investigated so far. Aim: Investigation of the impact of the blue visible light in porcine lens compared to UVA and UVB radiation. Materials and Methods: In this ex-vivo experiment, porcine lenses are irradiated with a dosage of 6 kJ/cm2 at wavelengths of 311 nm (UVB), 370 nm (UVA), and 460 nm (blue light). Lens transmission measurements before and after irradiation give insight into the impact of the radiation. Furthermore, dark field images are taken from every lens before and after irradiation. Cataract development is illustrated by histogram linearization as well as faults coloring of recorded dark field images. By segmenting the lens in the background’s original image, the lens condition before and after irradiation could be compared. Results: All lenses irradiated with a 6 kJ/cm2 reveal cataract development for radiation with 311 nm, 370 nm, and 460 nm. Both evaluations reveal that the 460 nm irradiation causes the most cataract. Conclusion: All investigated irradiation sources cause cataracts in porcine lenses—even blue visible light.

Xenon Plasma Focused Ion Beam Milling for Obtaining Soft X-ray Transparent Samples

We employ xenon (Xe) plasma focused ion beam (PFIB) milling to obtain soft X-ray transparent windows out of bulk samples. The use of a Xe PFIB allows for the milling of thin windows (several 100 nm thick) with areas of the order of 100 µm × 100 µm into bulk substrates. In addition, we present an approach to empirically determine the transmission level of such windows during fabrication by correlating their electron and soft X-ray transparencies. We perform scanning transmission X-ray microscopy (STXM) imaging on a sample obtained by Xe PFIB milling to demonstrate the conceptual feasibility of the technique. Our thinning approach provides a fast and simplified method for facilitating soft X-ray transmission measurements of epitaxial samples and it can be applied to a variety of different sample systems and substrates that are otherwise not accessible.