Distortion of a polycrystalline Al bar in a vice fixture: molecular dynamics analysis of grain movement and rotation

The deformation of a nano-sized polycrystalline Al bar under the action of vice plates is studied using molecular dynamics simulation. Two grain sizes are considered, fine-grained and coarse-grained. Deformation in the fine-grained sample is mainly caused by grain-boundary processes which induce grain displacement and rotation. Deformation in the coarse-grained sample is caused by grain-boundary processes and dislocation plasticity. The sample distortion manifests itself by the center-of-mass motion of the grains. Grain rotation is responsible for surface roughening after the loading process. While the plastic deformation is caused by the loading process, grain rearrangements under load release also contribute considerably to the final sample distortion.

Application of Load Release Factor Method in Thermal Expansion Load Imposed on Vessel Nozzle

The pressure vessels are connected by pipelines to form a system. Thermal expansion of the pipeline imposes an additional load on the nozzle of the connected vessel. There are two methods to deal with the thermal expansion load of pipeline in the design of pressure vessel: the partition method and the integrated method. A new Load Release Factor Method (LRFM) is proposed in this paper based on theoretical derivation. A spherical head with central nozzle is taken as an FEM (Finite Element Method) analysis model. The results show that a conservative design will be obtained by the traditional partition method, and the integrated method is the closest to the actual situation in spite of the large amount of calculation. However, compared with the traditional two methods, the LRFM can not only ensure the design margin but also reduce the calculation. This paper could be a reference for the analysis of pipeline thermal expansion load in the vessel design.

Structural Evidences for Present-day Compressive Tectonics at the St. Peter and St. Paul Archipelago (Equatorial Atlantic Ocean)

This paper discusses the tectonics of the St. Peter and St. Paul Archipelago (SPSPA) in the Equato-rial Atlantic Ocean, based on the joint-system geometry which show a North-South shorten-ing/transpressional uplift tectonism, is active leading to exhumation of the sub-oceanic mantle. These islets are the summits of a sigmoidal submarine ridge formed by mantle ultramafic rocks. The ridge is crossed by the principal transform deformation zone of the northern transform fault of the St. Paul Multifault System. The South flank ridge exposes serpentinized mantle perido-tites, while the North flank exposes strongly deformed/fractured ultramylonites, recording duc-tile and brittle deformation at lithospheric conditions. The SPSPA show multiple joint systems cutting mylonitic foliation of the exposed rocks, forming three main families: high-angle paral-lel joints of tectonic origin, serpentinization-related joints with random direction and load-release low-angle parallel joints. The tectonic joints show an average direction of N31°E and N28°W, forming a conjugate system with a N1ºW compression axes, coherent with a trans-pressive stress field. Accordingly, the earthquakes focal mechanism close to the islets also shows N-S compression. The previously reported active uplift with an average rate of 1.5 mm/year and the directions of the joint system here reported agreeing with a present-day active N-S compres-sive field at a high angle with the direction of the transform fault.

Distortion of a poly-crystalline Al bar in a vice fixture: Molecular dynamics analysis of grain movement and rotation

The deformation of a nano-sized polycrystalline Al bar under the action of vice plates is studied using molec- ular dynamics simulation. Two grain sizes are considered; deformation in the fine-grained sample is mainly caused by grain-boundary processes (sliding and rotation), while dislocation plasticity dominates in the coarse- grained sample. We show that the sample distortion is reflected by the center-of-mass motion of the grains. Grain rotation is responsible for surface roughening after the loading process. While the plastic deformation is caused by the loading process, grain rearrangements under load release also contribute considerably to the final sample distortion.

Postural Responses to Sudden Horizontal Perturbations in Tai Chi Practitioners

Tai Chi has been shown to elicit numerous positive effects on health and well-being. In this study, we examined reactive postural control after sudden unloading horizontal perturbations, which resembled situations encountered during Tai Chi. The study involved 20 participants, 10 in the Tai Chi group (age: 37.4 ± 7.8 years), who had been regularly training the push-hand technique for at least 7 years, and 10 in the control group, consisting of healthy adults (age: 28.8 ± 5.0). Perturbations were applied at three different positions (hips, shoulders, and arms) via the load-release paradigm. Twenty measurements were carried out for each perturbation position. We measured peak vertical and horizontal forces on the ground (expressed percentage of body mass (%BM)), peak center of pressure displacement and peak horizontal and vertical velocities at the knee, hip and shoulder joints. The Tai Chi group exhibited smaller increases in vertical ground reaction forces when perturbations were applied at the hips (11.5 ± 2.1 vs. 19.6 ± 5.5 %BW; p = 0.002) and the arms (14.1 ± 4.2 vs. 23.2 ± 8.4 %BW; p = 0.005). They also responded with higher horizontal force increase after hip perturbation (16.2 ± 3.2 vs. 13.1 ± 2.5 %BW; p < 0.001). Similar findings were found when observing various outcomes related to velocities of vertical movement. The Tai Chi group also showed lower speeds of backward movement of the knee (p = 0.005–0.009) after hip (0.49 ± 0.13 vs. 0.85 ± 0.14 m/s; p = 0.005) and arm perturbations (0.97 ± 0.18 vs. 1.71 ± 0.29 m/s; p = 0.005). Center of pressure displacements were similar between groups. Our study demonstrated that engaging in Tai Chi could be beneficial to reactive postural responses after sudden perturbations in a horizontal direction; however, future interventional studies are needed to directly confirm this. Moreover, because of the age difference between the groups, some confounding effects of age cannot be ruled out.

Differential Effects of Perturbation Magnitude on Reactive Balance Control in Young Sedentary Adults

This study investigates postural responses to unexpected perturbations induced by a load release of different weights. Groups of 26 men (age 22.6 ± 2.4 years, height 178.0 ± 9.1 cm, and body mass 86.9 ± 11.5 kg) and 21 women (age 21.9 ± 2.7 years, height 168.8 ± 6.8 cm, and body mass 65.3 ± 8.7 kg) underwent load-triggered postural perturbations by 1 and 2 kg while standing on a force plate with either eyes open or eyes closed. Postural perturbations induced by a heavier load, representing about 2% and 3% of body weight in men and women, respectively, led to significantly higher peak anterior and peak posterior center of pressure displacements when compared with a lighter load (29.6% and 45.4%, respectively) both with eyes open (36.9%) and closed (42.1%). Their values were significantly lower in men than women only when a higher load was used (∼25%). However, there were no significant differences in time to peak anterior and posterior center of pressure displacements. These findings indicate that heavier load-induced postural perturbations are greater in women than men regardless of visual conditions. This underlines the importance of loading dose in the magnitude of postural responses to externally induced perturbations.

Magnetic Properties of Silicon Steel after Plastic Deformation

The energy efficiency of electric machines can be improved by optimizing their manufacturing process. During the manufacturing of ferromagnetic cores, silicon steel sheets are cut and stacked. This process introduces large stresses near cutting edges. The steel near cutting edges is in a plastically deformed stress state without external mechanical load. The magnetic properties of the steel in this stress state are investigated using a custom magnetomechanical measurement setup, stress strain measurements, electrical resistance measurements, and transmission electron microscopic (TEM) measurements. Analysis of the core energy losses is done by means of the loss separation technique. The silicon steel used in this paper is non-grain oriented (NGO) steel grade M270-35A. Three differently cut sets of M270-35A are investigated, which differ in the direction they are cut with respect to the rolling direction. The effect of sample deformation was measured—both before and after mechanical load release—on the magnetization curve and total core energy losses. It is known that the magnetic properties dramatically degrade with increasing sample deformation under mechanical load. In this paper, it was found that when the mechanical load is released, the magnetic properties degrade even further. Loss separation analysis has shown that the hysteresis loss is the main contributor to the additional core losses due to sample deformation. Releasing the mechanical load increased the hysteresis loss up to 270% at 10.4% pre-release strain. At this level of strain, the relative magnetic permeability decreased up to 45% after mechanical load release. Manufacturing processes that introduce plastic deformation are detrimental to the local magnetic material properties.