Thermal regime of the local working zone in the industrial premises under radiant heating conditions

The results of experimental studies on recording temperatures and heat fluxes for the local working zone in industrial premises under radiant heating conditions and supply and exhaust ventilation operation are presented. The characteristics are measured on the surface of the horizontal remote panel directly under the radiator and along the wall with the ventilation inlet. Experimental results show that mixed convection caused by the operation of air exchange systems leads to mixing of air masses and more intensive cooling of the horizontal panel surface, as well as air, compared to the natural convection regime.

Binderless bark particleboard made from gelam (Melaleuca viridiflora Sol. ex Gaertn.) bark waste: The effect of the pressing temperature on its mechanical and physical properties

This study investigated the effects of the pressing temperature on the mechanical and physical properties of binderless bark particleboard made from Gelam bark waste and the improvement of those properties. In addition, the thermal insulation properties of the particleboard were determined. Four different temperatures (140 °C, 160 °C, 180 °C, and 200 °C) were used to make single-layer binderless bark particleboard with a target density of less than or equal to 0.59 g/cm3. Results revealed that the pressing temperature affected the mechanical properties (modulus of rupture, modulus of elasticity, and tensile strength perpendicular to panel surface), which increased as the temperature increased, and the physical properties (thickness swelling and water absorption), which decreased as the temperature increased. Based on the Tukey test, increasing the temperature from 180 to 200 °C did not significantly affect the mechanical or physical properties, except for the tensile strength perpendicular to panel surface. None of the mechanical properties met SNI standard 03-2105-2006 (2006); however, the 12% maximum thickness swelling requirement was met for binderless bark particleboard hot-pressed at 200 °C. Binderless bark particleboard hot-pressed at 200 °C had high water resistance, regardless of its low strength, and a thermal conductivity value of 0.14 W/m∙K.

SOLAR PANEL DUST MONITORING SYSTEM

Solar energy has been one of the most explored sources of renewable due to its economical source of energy. However, the main barrier for solar energy generation is the present of dust particles on the panel surface that decreases its performance. Hence, persistent monitoring on dust accumulation is of importance to guarantee the optimum power is achieved. Thus, this research aims to develop the real-time dust monitoring system of the solar panel. A dust sensor with IoT will be developed for this purpose. The reading of dust accumulation will be recorded and is accessible online through smartphones or desktop.

Eligibility Study on Floating Solar Panel Installation over Brackish Water in Sungsang, South Sumatra

Electric generation using the photovoltaic (PV) effect is considered ideal in South Sumatra as a response to the government policy to increase the utilization of renewable energy to support the depletion of conventional energy. PV panels can be installed in a fishing village in the Sungsang Estuary. This paper examined the eligibility analysis for the installation of PV panels on brackish water. In this research, two Panels are installed, the first one is floating over a water body, and the second is ground mounted as a comparison of electricity produced and efficiency. The Jsc floating and ground mounting differ in 0.4435 A. The measured Jload in floating PV panels is 0.3900 A higher than the ground mounting. The measured Voc at the floating PV panels is 0.2935 V higher, and the Vload of the floating PV panel is 3.0742 V higher than the ground mount. The differences are due to the floating PV panel surface temperature being lower than ground mounting. Electricity generated by floating PV panels is averagely 11.89 Watt higher, and the efficiency is 4% higher than that of ground installation. This experiment also shows that PV panels can be installed over brackish water in the fishing village of Sungsang Estuary.

Effects of quality grade and intramuscular location on beef semitendinosus muscle fiber characteristics, NADH content, and color stability

The objective of this study was to determine the impact of quality grade and steak location on color stability of semitendinosus (ST) steaks during a 9-d refrigerated study. Twenty-one ST muscles (12 Choice and 9 Select) were purchased from a commercial beef packing plant and fabricated into twelve 2.54-cm thick steaks per muscle. Steaks 1, 6, and 12 were designated for immunohistochemistry while remaining steak locations of proximal (steaks 2 to 4), middle (5 to 8), and distal (9 to 11) were randomly assigned to 0, 4, or 9 d of simulated retail display. Surface color attributes of day-9 steaks were recorded daily by a visual color panel and spectrophotometer. On days 0, 4, and 9 of display, steaks were analyzed for metmyoglobin reducing ability (MRA) and oxygen consumption (OC). Grade × day of display (DOD) interactions were detected for L*, a*, surface oxymyoglobin (OMb) and metmyoglobin (MMb) percentages, and visual panel surface redness and discoloration scores (P ≤ 0.02); however, no Grade × DOD interactions were observed for MRA or OC (P > 0.17). There were location main effect (LOC) × DOD interactions for L*, a*, surface MMb, visual panel surface redness and discoloration, and MRA (P ≤ 0.02). Distal steaks had lower L* values compared with the other locations (P < 0.01), which coincided with steaks being rated visually darker red (P < 0.01). Proximal steaks had greater a* values and had less surface discoloration than middle steaks (P < 0.05), which had an increased percentage of surface MMb (P ≤ 0.04). Distal and proximal steaks had increased MRA compared with middle steaks on days 0 and 4 (P < 0.05), and distal steaks had greater OC than the other locations throughout display (P < 0.01). There were fewer type I fibers at the proximal end with a greater percentage located at the middle and distal ends, and an increased percentage of type IIX fibers at the middle and proximal locations (P ≤ 0.01). Less type IIA fibers were detected at the middle LOC compared with the other two locations (P < 0.10). Larger type I, IIA, and IIX fibers were located at the proximal and middle locations compared with the distal LOC (P < 0.01). ST color and color-stability characteristics were influenced by DOD and LOC, which may partially be explained by differences in fiber types among locations.