Local Variations in Carbohydrates and Matrix Lignin in Mechanically Graded Bamboo Culms

The mechanical performance of bamboo is highly dependent on its structural arrangement and the properties of biomacromolecules within the cell wall. The relationship between carbohydrates topochemistry and gradient micromechanics of multilayered fiber along the diametric direction was visualized by combined microscopic techniques. Along the radius of bamboo culms, the concentration of xylan within the fiber sheath increased, while that of cellulose and lignin decreased gradually. At cellular level, although the consecutive broad layer (Bl) of fiber revealed a relatively uniform cellulose orientation and concentration, the outer Bl with higher lignification level has higher elastic modulus (19.59–20.31 GPa) than that of the inner Bl close to the lumen area (17.07–19.99 GPa). Comparatively, the cell corner displayed the highest lignification level, while its hardness and modulus were lower than that of fiber Bl, indicating the cellulose skeleton is the prerequisite of cell wall mechanics. The obtained cytological information is helpful to understand the origin of the anisotropic mechanical properties of bamboo.

RNAi suppression of xylan synthase genes in wheat starchy endosperm

The xylan backbone of arabinoxylan (AX), the major cell wall polysaccharide in the wheat starchy endosperm, is synthesised by xylan synthase which is a complex of three subunits encoded by the GT43_1, GT43_2 and GT47_2 genes. RNAi knock-down of either GT43_1 or all three genes (triple lines) resulted in decreased AX measured by digestion with endoxylanase (to 33 and 34.9% of the controls) and by monosaccharide analysis (to 45.9% and 47.4% of the controls) with greater effects on the amount of water-extractable AX (to 20.6 and 19.9% of the controls). Both sets of RNAi lines also had greater decreases in the amounts of substituted oligosaccharides released by digestion of AX with endoxylanase than in fragments derived only from the xylan backbone. Although the GT43_1 and triple lines had similar effects on AX they did differ in their contents of soluble sugars (increased in triple only) and on grain size (decreased in triple only). Both sets of transgenic lines had decreased grain hardness, indicating effects on cell wall mechanics. These results, and previously published studies of RNAi suppression of GT43_2 and GT47_2 and of a triple mutant of GT43_2, are consistent with the model of xylan synthase comprising three subunits one of which (GT47_2) is responsible for catalysis with the other two subunits being required for correct functioning but indicate that separate xylan synthase complexes may be responsible for the synthesis of populations of AX which differ in their structure and solubility.

Drying Stress and Strain of Wood: A Review

Wood drying stress causes various drying defects, which result from the wood microstructure and the transfer of heat and mass during the drying. It is the fundamental way to solve the problem of defects to clarify the law and mechanism of wood stress and strain development during drying. In this paper, based on the defects of wood drying, the theory and experimental testing methods of drying stress and strain were summarized. Meanwhile, artificial neural networks (ANN) and their application in the wood drying field were also investigated. The traditional prong and slicing methods were used practically in the research and industry of wood drying, but the stress changes in-process cannot be trapped. The technologies of image analysis and near-infrared spectroscopy provide a new opportunity for the detection of drying stress and strain. Hence, future interest should be attached to the combination of the theory of heat and mass transfer and their coupling during drying with the theory of microscopic cell wall mechanics and macroscopic drying. A more complete image acquisition and analysis system should be developed to realize the real-time monitoring of drying strain and cracking, practically. A more feasible and reasonable prediction model of wood drying stress and strain should be established to achieve the accuracy of the prediction.

Brassinosteroids Influence Arabidopsis Hypocotyl Graviresponses through Changes in Mannans and Cellulose

The force of gravity is a constant environmental factor. Plant shoots respond to gravity through negative gravitropism and gravity resistance. These responses are essential for plants to direct the growth of aerial organs away from the soil surface after germination and to keep an upright posture above ground. We took advantage of the effect of brassinosteroids (BRs) on the two types of graviresponses in Arabidopsis thaliana hypocotyls to disentangle functions of cell wall polymers during etiolated shoot growth. The ability of etiolated Arabidopsis seedlings to grow upward was suppressed in the presence of 24-epibrassinolide (EBL) but enhanced in the presence of brassinazole (BRZ), an inhibitor of BR biosynthesis. These effects were accompanied by changes in cell wall mechanics and composition. Cell wall biochemical analyses, confocal microscopy of the cellulose-specific pontamine S4B dye and cellular growth analyses revealed that the EBL and BRZ treatments correlated with changes in cellulose fibre organization, cell expansion at the hypocotyl base and mannan content. Indeed, a longitudinal reorientation of cellulose fibres and growth inhibition at the base of hypocotyls supported their upright posture whereas the presence of mannans reduced gravitropic bending. The negative effect of mannans on gravitropism is a new function for this class of hemicelluloses. We also found that EBL interferes with upright growth of hypocotyls through their uneven thickening at the base.

Mechanical properties of the fiber cell wall in Bambusa pervariabilis bamboo and analyses of their influencing factors

The cell wall mechanical properties are an important indicator for evaluating the overall mechanical properties of natural bamboo fibers. Using the nanoindentation technique, the variation of the mechanical properties of the fiber cell wall of Bambusa pervariabilis culms with different ages and different positions (both radial and longitudinal) was studied. Moreover, x-ray diffraction (XRD) was employed to measure the microfibril angle (MFA), and the correlation between the MFA and the mechanical properties of the fiber cell wall. The results showed that there was a remarkable difference in the fiber cell wall mechanical properties at different ages and at different radial and longitudinal positions. However, at different ages and at different positions, the absolute value of variation of MFA was less than 1° and was very minor. Furthermore, there was no significant correlation between the fiber cell wall mechanics and MFA, indicating that the mechanical property of the fiber cell walls might be synergistically affected by many factors.

Even Visually Intact Cell Walls in Waterlogged Archaeological Wood Are Chemically Deteriorated and Mechanically Fragile: A Case of a 170 Year-Old Shipwreck

Structural and chemical deterioration and its impact on cell wall mechanics were investigated for visually intact cell walls (VICWs) in waterlogged archaeological wood (WAW). Cell wall mechanical properties were examined by nanoindentation without prior embedding. WAW showed more than 25% decrease of both hardness and elastic modulus. Changes of cell wall composition, cellulose crystallite structure and porosity were investigated by ATR-FTIR imaging, Raman imaging, wet chemistry, 13C-solid state NMR, pyrolysis-GC/MS, wide angle X-ray scattering, and N2 nitrogen adsorption. VICWs in WAW possessed a cleavage of carboxyl in side chains of xylan, a serious loss of polysaccharides, and a partial breakage of β-O-4 interlinks in lignin. This was accompanied by a higher amount of mesopores in cell walls. Even VICWs in WAW were severely deteriorated at the nanoscale with impact on mechanics, which has strong implications for the conservation of archaeological shipwrecks.