Ways to improve poultry productivity

The article draws attention to the fact that the vitamin feed additive Introvit A+WS is an effective complex in its composition, consisting of 12 fat-and water-soluble vitamins, 18 essential and replaceable amino acids and 9 macro-and microelements that affect not only stability to various infectious diseases, but also to increase the meat productivity of young poultry. In recent years, industrially produced vitamins have become increasingly widespread, as well as feed additives used as a means of increasing animal productivity, reducing the cost of protein feed and increasing the efficiency of using feed nutrients. The vitamin feed additive Introvit A+WS in the indicated doses under production conditions had a positive effect on the weight gain of broilers and on the preservation of the poultry population, therefore, it shall be widely used in industrial poultry farming.

Uzbekistan and Turkmenistan.

This chapter focuses on the cotton cultivation, production conditions, commonly used cultivars, cottonseed production and pest management strategies in Uzbekistan and Turkmenistan. The future of cotton production in these countries is also discussed.

Influence of natural production conditions on efficient operation of wheel tractors

For the zones of “risky farming” characteristic of the Far East of the Russian Federation, the natural production conditions of the region are an important problem in preparing the soil for further basic agricultural work. So, when carrying out early spring agricultural work, due to presence of a solid underlying layer in the form of permafrost, they shall be completed in operational terms no more than 10 days, until the permafrost base thaws and the soil has not lost its bearing capacity. In addition, due to the peculiarities of the relief, the soil does not thaw equally in depth everywhere, which reduces the quality of field work and harrowing, as the most common operation, namely. This article provides theoretical and experimental studies on the adaptation of a wheeled tractor as part of a machine-tractor unit (MTU) used in harrowing to natural production conditions by installing a device that automatically regulates the load on the working body of the disc harrow or on the propellers of the energy device, depending on the conditions of use or the state of the motion surface.

Formation of biometric indicators of sugar beet hybrids of domestic breeding

Purpose. Find out the features of biometric indicators formation in sugar beet hybrids of domestic breeding. Methods. Field, laboratory. Results. According to the results of the research, it was determined that in early August, the maximum weight of roots (840 g) was in hybrid ‘ITsB 0904’. Good indicators were observed in hybrids ‘Umanskyi Ch S97’, ‘Soniachnyi’ and ‘Anichka’, 770, 780, and 800 g at the average group indicator of 730 g. It was investigated that the hybrid ‘Maksym’ (15.1%) and ‘Etiud’ (14.9%) were the best in terms of sugar accumulation in roots. Sugar content at the level of 14.8 % was observed in hybrids ‘Umanskyi ChS 97’, ‘Ramzes’, ‘Konstanta’, ‘Soniachnyi’ and ‘Verkhnia’ at the average group value of 14.5%. Conclusions. It is important to continue the study of the dynamics of root and leaf mass formation together with the process of sugar accumulation in roots in terms of establishing individual efficiency of hybrids and developing recommendations for the fullest realization of their potential in production conditions.

Cellulase Production by Penicillium Oxalicum Ti-11 with Traditional Chinese Medicine Residue as Substrate

PurposeThe study aims to search for efficient cellulase producer and explore the possibility of traditional Chinese medicine residue as a substrate for cellulase production, so as to realize the waste utilization of traditional Chinese medicine residue.MethodsThe cellulase-producing strain was identified through morphological and molecular biological methods. Scanning electron microscope (SEM) and Fourier transform infrared spectroscopy (FTIR) were used to characterize the structure of traditional Chinese medicine residues before and after fermentation. The enzyme activity was determined by DNS method, and the enzyme production conditions were optimized by single factor and response surface methodology.ResultThe strain grew well in forsythia leaf residue, and the highest FPA could reach 2.06 IU/mL. In addition, the structural characteristics of traditional Chinese medicine residue that before and after enzymatic hydrolysis were characterized by SEM and FTIR. The results showed that the structure of the residue was destroyed after enzymatic hydrolysis, the damage of forsythia leaf residue was the most serious, and enzymatic hydrolysis promoted the dissolution of cellulose, lignin and hemicellulose. The enzyme production conditions of the strain were optimized by Plackett-Burman design and response surface analysis. The FPA could reach 2.79 IU/mL under the optimal conditions of FLR concentration 24.84 g/L, (NH4)2SO4 concentration 2 g/L, temperature 34.44℃, pH 6.20, rotational speed 200rpm, inoculum 6%, which was 35.44% higher than that before optimization.ConclusionsThe results showed that traditional Chinese medicine residue could be used as the induced substrate for fungal cellulase production. This study provides an idea for the low-cost production of fungal cellulase and the waste utilization of traditional Chinese medicine residue.

Comparative Indicators of Grain Transportation When Unloading Combine Harvesters at the the Field Edge

Base don theresults of comparative experience in production conditions, the indicators of grain transportation by trucks were determined when unloading combine harvesters at the field edge.

Salivary Cortisol Concentration in Fattening Heifers Kept in an Enriched Environment at Different Stocking Densities

The aim of the study was to assess the effect of environmental enrichment and different stocking densities on the level of stress in the fattening cattle by measuring salivary cortisol concentration. A total of 320 saliva samples obtained from heifers during the final four-month fattening period was analyzed by a colorimetric competitive enzyme immunoassay. The heifers were housed at 3.3 and 4.5 m2/animal in standard production conditions that were additionally enriched with a mechanical grooming brush and salt blocks in experimental groups. The study results have demonstrated that a cortisol concentration at the end of fattening was significantly higher, as compared with the initial levels in all heifer groups, without significant intergroup differences. There was no significant correlation between the usage of a grooming brush and cortisol concentration, whereas a significant negative correlation was detected between the salt block usage and cortisol concentration, suggesting a beneficial effect of this simple, commercially available and relatively inexpensive environmental enrichment.

Evaluation of Pull Production Control Mechanisms by Simulation

Today, companies need to continuously improve their production processes, which is a complex task. Lean manufacturing is one of the methodologies for production improvement, and one of the basic goals of any lean implementation is to reduce work-in-process (WIP) and shorten the production lead time. One of the basic lean principles for achieving these goals is pull principle. The adoption of this principle is quite challenging, as it requires a long-term commitment in the application and adoption of various lean techniques and tools that are prerequisites for the successful introduction of the pull principle. Kanban is the most well-known pull production control mechanism, and the first one developed within Toyota production system, but later, other pull control mechanisms were developed. Some of them include Conwip, Hybrid Kanban/Conwip, and Drum Buffer Rope (DBR), and those three, together with Kanban, were the research topic of this study. These four mechanisms were not explored and compared all together not for these specific production configurations considered in this research but also with regard to optimal parameters of control mechanisms. The goal was to analyze and compare how these pull control mechanisms affect lead time in different production conditions. For this purpose, simulation experiments were performed. The results showed that for different production conditions, different pull control mechanisms are optimal in terms of shortening lead time. This finding could help companies as a guideline for making a decision in terms of which pull control mechanism to choose.