X.R.F. Analysis of Steelmaking Slags Using Special Sample Preparation Techniques

1978 ◽  
pp. 25-33 ◽  
Author(s):  
W. Van de Vrande ◽  
D. Cosma ◽  
W. Tekatch
Keyword(s):  
Sample Preparation ◽  
Steelmaking Slags ◽  
Special Sample Preparation ◽  
Preparation Techniques

X.R.F Analysis of Steelmaking Slags Using Special Sample Preparation Techniques

1977 ◽  
Vol 21 ◽  
pp. 25-33
Author(s):  
W. Van de Vrande ◽  
D. Cosma ◽  
W. Tekatch
Keyword(s):  
Sample Preparation ◽  
Metallic Iron ◽  
Preparation Technique ◽  
Free Lime ◽  
Sample Preparation Technique ◽  
Steelmaking Slags ◽  
Special Sample Preparation ◽  
The 1960S ◽  
Preparation Techniques ◽  
Different Levels

X.R.F. analysis of steelmaking slags has been done routinely since the 1960s. Fused buttons or pressed powdered pellets are used.Under certain conditions steelmaking slags may contain appreciable amounts of free lime and metallic iron droplets. These can cause gross inaccuracies in the result of the X.R.F. analysis as the normal correction procedures used in X-ray fluorescence techniques can not compensate for them.A special sample preparation technique as well as appropriate analytical procedures will be discussed. Examples of slags with different levels of free lime and metallic iron will be shown.

Document Examination Using Scanning Electron Microscopy & X-Ray Spectrometry

1985 ◽  
Vol 43 ◽  
pp. 126-127
Author(s):  
P. J. Nolan
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Sample Preparation ◽  
Alternative Methods ◽  
X Ray ◽  
Special Sample Preparation ◽  
Ink Analysis ◽  
Printing Ink ◽  
Preparation Techniques ◽  
Scanning Electron

This paper reviews the application of scanning electron microscopy and x-ray spectrometry to the examination of questioned documents that have been submitted to the author's laboratory. The use of the SEM is confined to examples where it can provide information unobtainable by alternative methods. This is demonstrated using a variety of examples including paper and printing ink analysis, and the examination of valuable documents, such as stamps. The strategy followed when attempting to determine the sequence of overlapping or intersecting writings is discussed. Special sample preparation techniques are explained and guidelines for optimizing instrumental conditions for different sample types are outlined.

Special Sample Preparation and Polishing

2010 ◽  
pp. 67-87
Keyword(s):  
Composite Materials ◽  
Sample Preparation ◽  
Microscopic Analysis ◽  
Polymeric Composite ◽  
Fiber Composites ◽  
Fiber Reinforced Composite ◽  
Boron Fiber ◽  
Reinforced Composite ◽  
Special Sample Preparation ◽  
Preparation Techniques

Abstract The most common methods for preparing polymeric composites for microscopic analysis can be used for most fiber-reinforced composite materials. There are, however, a few composite materials that require special preparation techniques. This chapter discusses the processes involved in the preparation of titanium honeycomb composites, boron fiber composites, titanium/polymeric composite hybrids, and uncured prepreg materials.

A Freeze Shadow Technique for the Preparation of Soft Paint Latexes for Electron Microscopy

1977 ◽  
Vol 35 ◽  
pp. 314-315
Author(s):  
Earl R. Walter ◽  
Glen H. Bryant
Keyword(s):  
Sample Preparation ◽  
High Vacuum ◽  
Vacuum System ◽  
Latex Particles ◽  
New Methods ◽  
Diffusion Pump ◽  
Film Forming ◽  
Routine Basis ◽  
Distribution Studies ◽  
Preparation Techniques

With the development of soft, film forming latexes for use in paints and other coatings applications, it became desirable to develop new methods of sample preparation for latex particle size distribution studies with the electron microscope. Conventional latex sample preparation techniques were inadequate due to the pronounced tendency of these new soft latex particles to distort, flatten and fuse on the substrate when they dried. In order to avoid these complications and obtain electron micrographs of undistorted latex particles of soft resins, a freeze-dry, cold shadowing technique was developed. The method has now been used in our laboratory on a routine basis for several years.The cold shadowing is done in a specially constructed vacuum system, having a conventional mechanical fore pump and oil diffusion pump supplying vacuum. The system incorporates bellows type high vacuum valves to permit a prepump cycle and opening of the shadowing chamber without shutting down the oil diffusion pump. A baffeled sorption trap isolates the shadowing chamber from the pumps.

Advanced TEM sample preparation techniques for submicron Si devices

1995 ◽  
Vol 53 ◽  
pp. 516-517 ◽  
Author(s):  
P. B. Basham ◽  
H. L. Tsai
Keyword(s):  
Sample Preparation ◽  
Process Development ◽  
Light Transmission ◽  
Specific Area ◽  
Turnaround Time ◽  
Small Hole ◽  
Area Of Interest ◽  
Transmission Electron ◽  
Polished Side ◽  
Preparation Techniques

The use of transmission electron microscopy (TEM) to support process development of advanced microelectronic devices is often challenged by a large amount of samples submitted from wafer fabrication areas and specific-spot analysis. Improving the TEM sample preparation techniques for a fast turnaround time is critical in order to provide a timely support for customers and improve the utilization of TEM. For the specific-area sample preparation, a technique which can be easily prepared with the least amount of effort is preferred. For these reasons, we have developed several techniques which have greatly facilitated the TEM sample preparation.For specific-area analysis, the use of a copper grid with a small hole is found to be very useful. With this small-hole grid technique, TEM sample preparation can be proceeded by well-established conventional methods. The sample is first polished to the area of interest, which is then carefully positioned inside the hole. This polished side is placed against the grid by epoxy Fig. 1 is an optical image of a TEM cross-section after dimpling to light transmission.

Novel Failure Analysis Sample Preparation Techniques for PoP Packaging

2012 ◽  
Author(s):  
Ng Sea Chooi ◽  
Chor Theam Hock ◽  
Ma Choo Thye ◽  
Khoo Poh Tshin ◽  
Dan Bockelman
Keyword(s):  
Sample Preparation ◽  
Failure Analysis ◽  
Failure Mechanisms ◽  
Preparation Process ◽  
Space Saving ◽  
Optical Probing ◽  
Preparation Techniques

Abstract Trends in the packaging of semiconductors are towards miniaturization and high functionality. The package-on-package(PoP) with increasing demands is beneficial in cost and space saving. The main failure mechanisms associated with PoP technology, including open joints and warpage, have created a lot of challenges for Assembly and Failure Analysis (FA). This paper outlines the sample preparation process steps to overcome the challenges to enable successful failure analysis and optical probing.

Sample Preparation Challenges In WLCSP Epoxy Underfill Coating Removal

2012 ◽  
Author(s):  
Jason H. Lagar ◽  
Rudolf A. Sia
Keyword(s):  
Sample Preparation ◽  
Failure Analysis ◽  
Vital Role ◽  
Fault Isolation ◽  
Wafer Level ◽  
Chip Scale Package ◽  
Coating Removal ◽  
Customer Returns ◽  
Preparation Techniques ◽  
Mechanical Defect

Abstract Most Wafer Level Chip Scale Package (WLCSP) units returned by customers for failure analysis are mounted on PCB modules with an epoxy underfill coating. The biggest challenge in failure analysis is the sample preparation to remove the WLCSP device from the PCB without inducing any mechanical defect. This includes the removal of the underfill material to enable further electrical verification and fault isolation analysis. This paper discusses the evaluations conducted in establishing the WLCSP demounting process and removal of the epoxy underfill coating. Combinations of different sample preparation techniques and physical failure analysis steps were evaluated. The established process enabled the electrical verification, fault isolation and further destructive analysis of WLCSP customer returns mounted on PCB and with an epoxy underfill coating material. This paper will also showcase some actual full failure analysis of WLCSP customer returns where the established process played a vital role in finding the failure mechanism.

A New Method of Wafer Level Plan View TEM Sample Preparation by DualBeam

2008 ◽  
Author(s):  
Hyoung H. Kang ◽  
Michael A. Gribelyuk ◽  
Oliver D. Patterson ◽  
Steven B. Herschbein ◽  
Corey Senowitz
Keyword(s):  
Sample Preparation ◽  
Ex Situ ◽  
Wafer Level ◽  
Cross Sectional ◽  
Plan View ◽  
Manufacturing Line ◽  
Transmission Electron ◽  
Thin Lamella ◽  
Preparation Techniques

Abstract Cross-sectional style transmission electron microscopy (TEM) sample preparation techniques by DualBeam (SEM/FIB) systems are widely used in both laboratory and manufacturing lines with either in-situ or ex-situ lift out methods. By contrast, however, the plan view TEM sample has only been prepared in the laboratory environment, and only after breaking the wafer. This paper introduces a novel methodology for in-line, plan view TEM sample preparation at the 300mm wafer level that does not require breaking the wafer. It also presents the benefit of the technique on electrically short defects. The methodology of thin lamella TEM sample preparation for plan view work in two different tool configurations is also presented. The detailed procedure of thin lamella sample preparation is also described. In-line, full wafer plan view (S)TEM provides a quick turn around solution for defect analysis in the manufacturing line.

Recent Developments in CE-MS Based Metabolomics

2020 ◽  
Vol 16 ◽  
Author(s):  
Mustafa Çelebier ◽  
Merve Nenni
Keyword(s):  
Sample Preparation ◽  
Scientific Information ◽  
Analytical Techniques ◽  
Living Organism ◽  
Analytical Technique ◽  
Ionic Compounds ◽  
Recent Sample ◽  
Recent Developments ◽  
Endogenous Metabolites ◽  
Preparation Techniques

Background: Metabolomics has gained importance in clinical applications over the last decade. Metabolomics studies are significant because the systemic metabolome is directly affected by disease conditions. Metabolome-based biomarkers are actively being developed for early diagnosis and to indicate the stage of specific diseases. Additionally, understanding the effect of an intervention on a living organism at the molecular level is a crucial strategy for understanding novel or unexpected biological processes. Results: The simultaneous improvements in advanced analytical techniques, sample preparation techniques, computer technology, and databank contents has enabled more valuable scientific information to be gained from metabolomics than ever before. With over 15,000 known endogenous metabolites, there is no single analytical technique capable of analyzing the whole metabolome. However, capillary electrophoresis-mass spectrometry (CE-MS) is a unique technique used to analyze an important portion of metabolites not accessible by liquid chromatography or gas chromatography techniques. The analytical capability of CE, combined with recent sample preparation techniques focused on extracting polar-ionic compounds, make CE-MS a perfect technique for metabolomic studies. Conclusion: Here, previous reviews of CE-MS based metabolomics are evaluated to highlight recent improvements in this technique. Specifically, we review papers from the last two years (2018 and 2019) on CE-MS based metabolomics. The current situation and the challenges facing metabolomic studies are discussed to reveal the high potential of CE-MS for further studies, especially in biomarker development studies.

Sign in / Sign up

Export Citation Format

Share Document