The strain-rate and temperature dependence of the mechanical properties of polyetherketone and polyetheretherketone

1996 ◽  
Vol 31 (6) ◽  
pp. 1415-1423 ◽  
Author(s):  
S. Hamdan ◽  
G. M. Swallowe
Keyword(s):  
Mechanical Properties ◽  
Strain Rate ◽  
Temperature Dependence

scholarly journals Mechanical properties of biaxially strained poly(l -lactide) tubes: Strain rate and temperature dependence

2017 ◽  
Vol 134 (33) ◽  
pp. 45192 ◽  
Author(s):  
Alexandra Liv Vest Løvdal ◽  
Jens W. Andreasen ◽  
Lars P. Mikkelsen ◽  
Karsten Agersted ◽  
Kristoffer Almdal
Keyword(s):  
Mechanical Properties ◽  
Strain Rate ◽  
Temperature Dependence

Extreme strain rate and temperature dependence of the mechanical properties of nano silicon nitride thin layers in a basal plane under tension: a molecular dynamics study

2014 ◽  
Vol 16 (29) ◽  
pp. 15551-15557 ◽  
Author(s):  
Xuefeng Lu ◽  
Hongjie Wang ◽  
Yin Wei ◽  
Jiangbo Wen ◽  
Min Niu ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Molecular Dynamics ◽  
Silicon Nitride ◽  
Strain Rate ◽  
Mechanical Behavior ◽  
Temperature Dependence ◽  
Basal Plane ◽  
Thin Layers ◽  
Nano Silicon

The extreme strain rate and temperature dependence of the mechanical behavior of nano silicon nitride thin layers in a basal plane are determined.

Mechanical Properties of a β Containing Ti-Al-Cr-Alloy at Ambient and Elevated Temperatures

1994 ◽  
Vol 364 ◽  
Author(s):  
W. R. Chen ◽  
J. Wang ◽  
B. Zhang ◽  
X. Wan ◽  
W. J. Chen
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Ambient Temperature ◽  
Strain Rate ◽  
Temperature Dependence ◽  
Elevated Temperatures ◽  
High Tensile Strength ◽  
Tial Alloys ◽  
Β Phase ◽  
Very High

AbstractThe mechanical properties of a β-containing Ti-Al-Cr alloy were investigated at ambient and elevated temperatures. The results show that the Ti-Al-Cr alloy containing the β phase has a very high tensile strength but a poor ductility at ambient temperature, and that higher ductility is obtained at high temperatures. The temperature dependence of mechanical properties is found to be sensitive to the strain rate during the test. Fractography shows that the fracture mode changes from fully brittle to ductile-brittle mixture with the increased temperature. All the results suggest that the triple-phased TiAl alloys (α2+β+γ) may have the combined mechanical properties of the dual-phased T13Al ((α2+β) and dual-phased TiAl (α2+γ) alloys.

The Temperature Dependence of the Mechanical Properties of Gamma TiAl

1994 ◽  
Vol 364 ◽  
Author(s):  
B. Viguier ◽  
J. Bonneville ◽  
K. J. Hemker ◽  
J. L. Martin
Keyword(s):  
Mechanical Properties ◽  
Flow Stress ◽  
Strain Rate ◽  
Temperature Dependence ◽  
Single Crystals ◽  
Strain Rate Sensitivity ◽  
Rate Sensitivity ◽  
Dislocation Motion ◽  
Compression Tests ◽  
Wide Range

AbstractMechanical properties of a polycrystalline single phased γ Ti47Al51Mn2 alloy were studied by compression tests in a wide range of temperature (100 K - 1300 K). We report, in this paper, the temperature dependence of both the flow stress and its strain rate sensitivity. These dependencies show the existence of three temperature domains corresponding to different dislocation motion mechanisms. The temperature dependence of the flow stress strain rate sensitivity is compared with values measured in single crystals1.

scholarly journals A Review on Mechanical Properties of Natural Fibre Reinforced Polymer Composites under Various Strain Rates

2021 ◽  
Vol 5 (5) ◽  
pp. 130
Author(s):  
Tan Ke Khieng ◽  
Sujan Debnath ◽  
Ernest Ting Chaw Liang ◽  
Mahmood Anwar ◽  
Alokesh Pramanik ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Strain Rate ◽  
Polymer Composites ◽  
Stress Transfer ◽  
Natural Fibre ◽  
Transfer Efficiency ◽  
Strain Rates ◽  
Reinforced Polymer ◽  
Fibre Reinforced Polymer ◽  
Fibre Matrix

With the lightning speed of technological evolution, the demand for high performance yet sustainable natural fibres reinforced polymer composites (NFPCs) are rising. Especially a mechanically competent NFPCs under various loading conditions are growing day by day. However, the polymers mechanical properties are strain-rate dependent due to their viscoelastic nature. Especially for natural fibre reinforced polymer composites (NFPCs) which the involvement of filler has caused rather complex failure mechanisms under different strain rates. Moreover, some uneven micro-sized natural fibres such as bagasse, coir and wood were found often resulting in micro-cracks and voids formation in composites. This paper provides an overview of recent research on the mechanical properties of NFPCs under various loading conditions-different form (tensile, compression, bending) and different strain rates. The literature on characterisation techniques toward different strain rates, composite failure behaviours and current challenges are summarised which have led to the notion of future study trend. The strength of NFPCs is generally found grow proportionally with the strain rate up to a certain degree depending on the fibre-matrix stress-transfer efficiency. The failure modes such as embrittlement and fibre-matrix debonding were often encountered at higher strain rates. The natural filler properties, amount, sizes and polymer matrix types are found to be few key factors affecting the performances of composites under various strain rates whereby optimally adjust these factors could maximise the fibre-matrix stress-transfer efficiency and led to performance increases under various loading strain rates.

scholarly journals Static Mechanical Properties of Expanded Polypropylene Crushable Foam

Materials ◽  
2021 ◽  
Vol 14 (2) ◽  
pp. 249
Author(s):  
Przemysław Rumianek ◽  
Tomasz Dobosz ◽  
Radosław Nowak ◽  
Piotr Dziewit ◽  
Andrzej Aromiński
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
Strain Rate ◽  
Energy Absorption ◽  
Experimental Tests ◽  
Absorption Capacity ◽  
Strain Rates ◽  
Foam Density ◽  
Energy Absorption Capacity ◽  
Closed Cell

Closed-cell expanded polypropylene (EPP) foam is commonly used in car bumpers for the purpose of absorbing energy impacts. Characterization of the foam’s mechanical properties at varying strain rates is essential for selecting the proper material used as a protective structure in dynamic loading application. The aim of the study was to investigate the influence of loading strain rate, material density, and microstructure on compressive strength and energy absorption capacity for closed-cell polymeric foams. We performed quasi-static compressive strength tests with strain rates in the range of 0.2 to 25 mm/s, using a hydraulically controlled material testing system (MTS) for different foam densities in the range 20 g/dm3 to 220 g/dm3. The above tests were carried out as numerical simulation using ABAQUS software. The verification of the properties was carried out on the basis of experimental tests and simulations performed using the finite element method. The method of modelling the structure of the tested sample has an impact on the stress values. Experimental tests were performed for various loads and at various initial temperatures of the tested sample. We found that increasing both the strain rate of loading and foam density raised the compressive strength and energy absorption capacity. Increasing the ambient and tested sample temperature caused a decrease in compressive strength and energy absorption capacity. For the same foam density, differences in foam microstructures were causing differences in strength and energy absorption capacity when testing at the same loading strain rate. To sum up, tuning the microstructure of foams could be used to acquire desired global materials properties. Precise material description extends the possibility of using EPP foams in various applications.

Sign in / Sign up

Export Citation Format

Share Document