Cutting speed modelling in ball nose milling applications

2014 ◽  
Vol 73 (1-4) ◽  
pp. 161-171 ◽  
Author(s):  
Jianhua Fan
Keyword(s):  
Cutting Speed ◽  
Ball Nose Milling

Deformation Replication

1970 ◽  
Vol 28 ◽  
pp. 280-281
Author(s):  
J. Temple Black
Keyword(s):  
Cutting Speed ◽  
Machining Process ◽  
Depth Of Cut ◽  
Rake Face ◽  
Orthogonal Machining ◽  
Aluminum Chips ◽  
Before And After ◽  
Materials Used ◽  
Glass Knife ◽  
Very High

Tool materials used in ultramicrotomy are glass, developed by Latta and Hartmann (1) and diamond, introduced by Fernandez-Moran (2). While diamonds produce more good sections per knife edge than glass, they are expensive; require careful mounting and handling; and are time consuming to clean before and after usage, purchase from vendors (3-6 months waiting time), and regrind. Glass offers an easily accessible, inexpensive material ($0.04 per knife) with very high compressive strength (3) that can be employed in microtomy of metals (4) as well as biological materials. When the orthogonal machining process is being studied, glass offers additional advantages. Sections of metal or plastic can be dried down on the rake face, coated with Au-Pd, and examined directly in the SEM with no additional handling (5). Figure 1 shows aluminum chips microtomed with a 75° glass knife at a cutting speed of 1 mm/sec with a depth of cut of 1000 Å lying on the rake face of the knife.

Effects of Vibration on the Preparation of Ultrathin Sections

1973 ◽  
Vol 31 ◽  
pp. 358-359
Author(s):  
Joseph M. Blum ◽  
Edward P. Gargiulo ◽  
J. R. Sawers
Keyword(s):  
Cutting Speed ◽  
Ground Level ◽  
Environmental Vibration ◽  
Block Face ◽  
Ultrathin Sections ◽  
Embedding Medium ◽  
Thickness Variations ◽  
Building Walls ◽  
Cutting Direction ◽  
Diamond Knife

It is now well-known that chatter (Figure 1) is caused by vibration between the microtome arm and the diamond knife. It is usually observed as a cyclical variation in “optical” density of an electron micrograph due to sample thickness variations perpendicular to the cutting direction. This vibration might be induced by using too large a block face, too large a clearance angle, excessive cutting speed, non-uniform embedding medium or microtome vibration. Another prominent cause is environmental vibration caused by inadequate building construction. Microtomes should be installed on firm, solid floors. The best floors are thick, ground-level concrete pads poured over a sand bed and isolated from the building walls. Even when these precautions are followed, we recommend an additional isolation pad placed on the top of a sturdy table.

Effects of Process Parameters on Surface Roughness and MRR in the hard turning of EN 36 steel

2018 ◽  
pp. 102-110
Author(s):  
Amritpal Singh ◽  
Rakesh Kumar
Keyword(s):  
Surface Roughness ◽  
Material Removal Rate ◽  
Material Removal ◽  
Hard Turning ◽  
Control Parameter ◽  
Removal Rate ◽  
Cutting Speed ◽  
Depth Of Cut ◽  
Cutting Condition ◽  
Dry Cutting

In the present study, Experimental investigation of the effects of various cutting parameters on the response parameters in the hard turning of EN36 steel under the dry cutting condition is done. The input control parameters selected for the present work was the cutting speed, feed and depth of cut. The objective of the present work is to minimize the surface roughness to obtain better surface finish and maximization of material removal rate for better productivity. The design of experiments was done with the help of Taguchi L9 orthogonal array. Analysis of variance (ANOVA) was used to find out the significance of the input parameters on the response parameters. Percentage contribution for each control parameter was calculated using ANOVA with 95 % confidence value. From results, it was observed that feed is the most significant factor for surface roughness and the depth of cut is the most significant control parameter for Material removal rate.

KINEMATIC FEATURES OF THE LAPPING PROCESS AND DETERMINATION OF ITS BASIC PARAMETERS

2020 ◽  
Vol 7 (3) ◽  
pp. 23-28
Author(s):  
EZIZ SARVAN SHIRVAN ◽  
Keyword(s):  
Dynamic Properties ◽  
Cutting Speed ◽  
Equilibrium System ◽  
Technological Parameters ◽  
Kinematic Characteristics ◽  
Angular Velocities ◽  
Basic Parameters ◽  
Grinding Tool ◽  
Mathematical Relationships ◽  
Analytical Expressions

This paper discusses the kinematic characteristics of lapping process and the main parameters of the process. It was determined that the influencing degree of technological parameters to the forming surface and processes. It was projected the construction of the lapping head for processing of internal cylindrical surfaces, scheme of the lapping operation and graphic description of the forces influencing. The relationships between the axial, radial and tangential cutting forces and the effect of the combined force thereof are determined in order to ensure the necessary surface pressure. During the analysis geometric and mathematical relationships were obtained. The extracted analytical expressions can be realized by further experimental researches and can be used in engineering calculations of technological parameters of processing by lapping. Angular velocity, friction force, linear velocity, also the length of the tactile curve and the radius of the part can be considered the main kinematic and dynamic parameters of the process that the formation of the surface, also the course of the process depends on these parameters. Depending on the kinematic parameters, the wear nature of the tool changes and this changes the linear and angular velocities, which have a significant impact on the accuracy, quality and productivity of processing. When examining the technological capabilities of the process, the nature of the movement between the part and the grinding tool, also changes in cutting speed are often considered as a main factor. Analytical expressions were obtained to determine the main parameters of the process, taking into account the kinematic characteristics of the friction process. These expressions can be used in engineering calculations and allow to determine the optimal values of the processing mode. In order to obtain the required micrometric surface cleanliness and measurement accuracy, correlation relationships were established between the main parameters of the process, equations of the equilibrium system of shear forces were compiled and analytical expressions were obtained based on the analysis of kinematic and dynamic properties of the system.

Performance Analysis of Trihexyltetradecylphosphonium Chloride Ionic Fluid under MQL Condition in Hard turning

2020 ◽  
Vol 17 (1) ◽  
pp. 7629-7647
Author(s):  
A. Pandey ◽  
R. Kumar ◽  
A. K. Sahoo ◽  
A. Paul ◽  
A. Panda
Keyword(s):  
Material Removal Rate ◽  
Feed Rate ◽  
Material Removal ◽  
Removal Rate ◽  
Cutting Speed ◽  
Coconut Oil ◽  
Chip Morphology ◽  
Weight Fraction ◽  
Cutting Fluid ◽  
Depth Of Cut

The current research presents an overall performance-based analysis of Trihexyltetradecylphosphonium Chloride [[CH3(CH2)5]P(Cl)(CH2)13CH3] ionic fluid mixed with organic coconut oil (OCO) during turning of hardened D2 steel. The application of cutting fluid on the cutting interface was performed through Minimum Quantity Lubrication (MQL) approach keeping an eye on the detrimental consequences of conventional flood cooling. PVD coated (TiN/TiCN/TiN) cermet tool was employed in the current experimental work. Taguchi’s L9 orthogonal array and TOPSIS are executed to analysis the influences, significance and optimum parameter settings for predefined process parameters. The prime objective of the current work is to analyze the influence of OCO based Trihexyltetradecylphosphonium Chloride ionic fluid on flank wear, surface roughness, material removal rate, and chip morphology. Better quality of finish (Ra = 0.2 to 1.82 µm) was found with 1% weight fraction but it is not sufficient to control the wear growth. Abrasion, chipping, groove wear, and catastrophic tool tip breakage are recognized as foremost tool failure mechanisms. The significance of responses have been studied with the help of probability plots, main effect plots, contour plots, and surface plots and the correlation between the input and output parameters have been analyzed using regression model. Feed rate and depth of cut are equally influenced (48.98%) the surface finish while cutting speed attributed the strongest influence (90.1%). The material removal rate is strongly prejudiced by cutting speed (69.39 %) followed by feed rate (28.94%) whereas chip reduction coefficient is strongly influenced through the depth of cut (63.4%) succeeded by feed (28.8%). TOPSIS significantly optimized the responses with 67.1 % gain in closeness coefficient.

Possible examinations of stone machining focused on the relationship between technological parameters and surface quality

2013 ◽  
Vol 4 (1) ◽  
pp. 63-68 ◽  
Author(s):  
Zs. Kun ◽  
I. G. Gyurika
Keyword(s):  
Surface Roughness ◽  
Metal Cutting ◽  
Cutting Speed ◽  
Theoretical Background ◽  
Motion Path ◽  
Depth Of Cut ◽  
Manufacturing Cost ◽  
Technological Parameters ◽  
The Relationship ◽  
Manufacturing Time

Abstract The stone products with different sizes, geometries and materials — like machine tool's bench, measuring machine's board or sculptures, floor tiles — can be produced automatically while the manufacturing engineer uses objective function similar to metal cutting. This function can minimise the manufacturing time or the manufacturing cost, in other cases it can maximise of the tool's life. To use several functions, manufacturing engineers need an overall theoretical background knowledge, which can give useful information about the choosing of technological parameters (e.g. feed rate, depth of cut, or cutting speed), the choosing of applicable tools or especially the choosing of the optimum motion path. A similarly important customer's requirement is the appropriate surface roughness of the machined (cut, sawn or milled) stone product. This paper's first part is about a five-month-long literature review, which summarizes in short the studies (researches and results) considered the most important by the authors. These works are about the investigation of the surface roughness of stone products in stone machining. In the second part of this paper the authors try to determine research possibilities and trends, which can help to specify the relation between the surface roughness and technological parameters. Most of the suggestions of this paper are about stone milling, which is the least investigated machining method in the world.

DESIGNING AND MANUFACTURING HARVESTING MACHINE FOR CENTELLA ASIATICA

2017 ◽  
Vol 126 (2B) ◽  
Author(s):  
Nguyễn Hữu Chúc ◽  
Nguyễn Văn Anh ◽  
Ngô Viết Anh Văn ◽  
Trần Đại Hiếu
Keyword(s):  
Cutting Speed ◽  
Centella Asiatica ◽  
Optimal Speed ◽  
Moving Speed

<p>This paper presents the designing, manufacturing and piloting process of havesting machine for Centella Asiatica serving Quang Tho 2 Agricultural Commune. This model is designed and manufactured on the basis of the survey taken on the characteristics of Centella Asiatica in Quang Tho 2 Agricultural Commune of Thua Thien Hue Province. Within project, experiments on machine’s moving speed, cutting speed and optimal speed are carried out. Results obttained in these experiments prove the efficiency of the proposed machine designed by authors.</p>

Experimental and Numerical Investigation into Residual Stress During Turning Operation for Stainless Steel AISI 316

2020 ◽  
Vol 38 (12A) ◽  
pp. 1862-1870
Author(s):  
Safa M. Lafta ◽  
Maan A. Tawfiq
Keyword(s):  
Stainless Steel ◽  
Residual Stresses ◽  
Orthogonal Cutting ◽  
Cutting Tools ◽  
Cutting Speed ◽  
Percentage Error ◽  
Depth Of Cut ◽  
Main Role ◽  
Turning Operation ◽  
Aisi 316

RS (residual stresses) represent the main role in the performance of structures and machined parts. The main objective of this paper is to investigate the effect of feed rate with constant cutting speed and depth of cut on residual stresses in orthogonal cutting, using Tungsten carbide cutting tools when machining AISI 316 in turning operation. AISI 316 stainless steel was selected in experiments since it is used in many important industries such as chemical, petrochemical industries, power generation, electrical engineering, food and beverage industry. Four feed rates were selected (0.228, 0.16, 0.08 and 0.065) mm/rev when cutting speed is constant 71 mm/min and depth of cutting 2 mm. The experimental results of residual stresses were (-15.75, 12.84, 64.9, 37.74) MPa and the numerical results of residual stresses were (-15, 12, 59, and 37) MPa. The best value of residual stresses is (-15.75 and -15) MPa when it is in a compressive way. The results showed that the percentage error between numerical by using (ABAQUS/ CAE ver. 2017) and experimental work measured by X-ray diffraction is range (2-15) %.

Optimization of Cutting Parameters in Milling Process Using Genetic Algorithm and ANOVA (March 2020)

2020 ◽  
Vol 38 (10A) ◽  
pp. 1489-1503
Author(s):  
Marwa Q. Ibraheem
Keyword(s):  
Genetic Algorithm ◽  
Tool Wear ◽  
Material Removal Rate ◽  
Material Removal ◽  
Removal Rate ◽  
Cutting Speed ◽  
Cutting Parameters ◽  
Depth Of Cut ◽  
Optimal Value ◽  
Optimization Of Cutting Parameters

In this present work use a genetic algorithm for the selection of cutting conditions in milling operation such as cutting speed, feed and depth of cut to investigate the optimal value and the effects of it on the material removal rate and tool wear. The material selected for this work was Ti-6Al-4V Alloy using H13A carbide as a cutting tool. Two objective functions have been adopted gives minimum tool wear and maximum material removal rate that is simultaneously optimized. Finally, it does conclude from the results that the optimal value of cutting speed is (1992.601m/min), depth of cut is (1.55mm) and feed is (148.203mm/rev) for the present work.

INVESTIGATION OF DEPENDENCE IMPACT OF TOOL GEOMETRICAL PARAMETERS AND CUTTING SPEED UPON SHAPING EFFORT AT HELICAL GROOVE CUTTING ON INTERNAL SURFACE OF CYLINDRICAL SHELL

2020 ◽  
Vol 2020 (10) ◽  
pp. 22-28
Author(s):  
Vadim Kuc ◽  
Dmitriy Gridin
Keyword(s):  
Finite Element Method ◽  
Finite Element ◽  
Cylindrical Shell ◽  
Contact Interaction ◽  
Cutting Speed ◽  
Internal Surface ◽  
Geometrical Parameters ◽  
Software Complex ◽  
Helical Groove ◽  
Groove Cutting

The work purpose was the investigation of dependence impact of tool geometrical parameters upon shaping effort during internal groove cutting. As a realization for the fulfillment of the helical groove processing investigation there was used a software complex based on a finite element method and a computer mathematic system. As a result of the investigations carried out there was obtained a regression equation manifesting the dependence of factors impact upon axial force falling on one tooth of the tool in the set scale of factor parameters. The scientific novelty consists in that in the paper there is considered a new method for helical groove cutting in which a shaping motion is carried out at the expense of the contact interaction of a tool and a billet performing free cutting. The investigation results obtained allowed determining the number of teeth operating simultaneously, that can be used further at cutting mode setting, and also as recommendations during designing tool design.

Sign in / Sign up

Export Citation Format

Share Document