scholarly journals Tool wear development in gear skiving process of quenched and tempered internal gears

2021 ◽  
Author(s):  
Tassilo Arndt ◽  
Jan Klose ◽  
Michael Gerstenmeyer ◽  
Volker Schulze
Keyword(s):  
Tool Wear ◽  
Tool Life ◽  
High Performance ◽  
Cutting Speed ◽  
High Strength ◽  
Cutting Parameters ◽  
Machining Process ◽  
Process Understanding ◽  
Complex Process ◽  
Drive Trains

AbstractGear skiving is a highly productive machining process, especially for manufacturing of high strength internal gears as required for high performance electric drive trains. However, the complex process kinematics cause intense variations of the effective cutting parameters during tool engagement. Thus, particularly the tool must meet high requirements to achieve long tool life at required workpiece quality. These requirements are amplified even more when machining quenched and tempered materials from the massive blank.In the presented study, the influence of various key factors on the tool wear development in gear skiving process are quantified. In several tests, the cutting speed, workpiece tensile strength, cooling lubricant strategy, as well as the cutting strategy are varied in order to optimize tool life. Therefore, single-tooth tests on quenched and tempered internal gears from 31CrMoV9 (AISI 4340) steel are conducted and wear flank land width evolution of the tools is examined. In addition, the workpiece is evaluated with regard to surface quality. Results reveal that different factor level combinations can have various effects on tool wear characteristics and therefore on tool life. The correlations presented provide recommendations for practical application and contribute to deeper process understanding.

Empirical Expression of Tool Wear When Face Milling 416 SS

2009 ◽  
Author(s):  
Patricia Mun˜oz de Escalona ◽  
Paul G. Maropoulos
Keyword(s):  
Tool Wear ◽  
Tool Life ◽  
Cutting Speed ◽  
Cutting Parameters ◽  
Face Milling ◽  
Machining Process ◽  
Depth Of Cut ◽  
Milling Operation ◽  
Increase Tool Life ◽  
The Cost

During a machining process, cutting parameters must be taken into account, since depending on them the cutting edge starts to wear out to the point that tool can fail and needs to be change, which increases the cost and time of production. Since wear is a negative phenomenon on the cutting tool, due to the fact that tool life is reduced, it is important to optimize the cutting variables to be used during the machining process, in order to increase tool life. This research is focused on the influence of cutting parameters such as cutting speed, feed per tooth and axial depth of cut on tool wear during a face milling operation. The Taguchi method is applied in this study, since it uses a special design of orthogonal array to study the entire parameters space, with only few numbers of experiments. Also a relationship between tool wear and the cutting parameters is presented. For the studies, a martensitic 416 stainless steel was selected, due to the importance of this material in the machining of valve parts and pump shafts.

scholarly journals Prediction of Tool Lifetime and Surface Roughness for Nickel-Based Waspaloy

2020 ◽  
Vol 2020 ◽  
pp. 1-12
Author(s):  
Shao-Hsien Chen ◽  
Chung-An Yu
Keyword(s):  
Surface Roughness ◽  
Tool Wear ◽  
High Speed ◽  
Cutting Speed ◽  
High Strength ◽  
Cutting Parameters ◽  
Experimental Results ◽  
Predictive Values ◽  
Actual Surface ◽  
Wide Range

In recent years, most of nickel-based materials have been used in aircraft engines. Nickel-based materials applied in the aerospace industry are used in a wide range of applications because of their strength and rigidity at high temperature. However, the high temperatures and high strength caused by the nickel-based materials during cutting also reduce the tool lifetime. This research aims to investigate the tool wear and the surface roughness of Waspaloy during cutting with various cutting speeds, feed per tooth, cutting depth, and other cutting parameters. Then, it derives the formula for the tool lifetime based on the experimental results and explores the impacts of these cutting parameters on the cutting of Waspaloy. Since the impacts of cutting speed on the cutting of Waspaloy are most significant in accordance with the experimental results, the high-speed cutting is not recommended. In addition, the actual surface roughness of Waspaloy is worse than the theoretical surface roughness in case of more tool wear. Finally, a set of mathematical models can be established based on these results, in order to predict the surface roughness of Waspaloy cut with a worn tool. The errors between the predictive values and the actual values are 5.122%∼8.646%. If the surface roughness is within the tolerance, the model can be used to predict the residual tool lifetime before the tool is damaged completely. The errors between the predictive values and the actual values are 8.014%∼20.479%.

Turning of Austempered Ductile Iron with ceramic tools

2020 ◽  
pp. 095440542095715 ◽  
Author(s):  
A Fernández-Valdivielso ◽  
LN López de Lacalle ◽  
P Fernández-Lucio ◽  
H González
Keyword(s):  
Heat Treatment ◽  
Tool Wear ◽  
Ductile Iron ◽  
High Strength ◽  
Cutting Parameters ◽  
Precise Determination ◽  
Machining Process ◽  
Austempered Ductile Iron ◽  
Machining Time ◽  
Ceramic Tools

Austempered ductile iron castings (ADI) are characterized by the high strength and resistance to fatigue, impact, and wear. ADI mechanical properties are obtained by performing a heat treatment on ductile iron casting. Thus, the so-called ausferrite microstructure is achieved. However, heat treatment significantly affects ductile casting machinability. A precise determination of ADI microstructure, on the one hand, and to choose correct machining process parameters and tool wear control on the other, are essential to optimize cutting processes and for the introduction of ceramic inserts. Ceramics are an alternative to carbide tools. In this paper, ceramic tools for the dry turning of ADI castings are studied. Thus, different technical ceramics were analyzed, identifying the dominant wear mechanism and evolution. Tool wear rate magnitude was determined indirectly by the variation of cutting force along machining time. Finally, different tests helped to study ceramics wear sensitivity with respect to cutting parameters. Mixed ceramics of Al2O3 with TiC showed the best performance, followed by SiAlON ones.

Wear Characteristic and Life of Al2O3/(W,Ti)C Ceramic Tool in Turning Iron-Based P/M Composites

2010 ◽  
Vol 26-28 ◽  
pp. 1052-1055
Author(s):  
Li Fa Han ◽  
Sheng Guan Qu
Keyword(s):  
Tool Wear ◽  
Tool Life ◽  
Empirical Model ◽  
Feed Rate ◽  
Flank Wear ◽  
Cutting Speed ◽  
Cutting Parameters ◽  
Depth Of Cut ◽  
Ceramic Tool ◽  
Iron Based

The wear characteristics and life of Al2O3/(W,Ti)C ceramic tool in turning NbCp-reinforced iron-based P/M composites was investigated. Experimental results indicate that cutting parameters have an influence on tool wear, among which cutting speed and depth of cut seem to be more prominent. The maximum flank wear rapidly increases as the increase in cutting speed and depth of cut. While, it increases gradually as the decrease in feed rate. Meanwhile, an empirical model of tool life is established, from which the influence of cutting speed and depth of cut on tool life is far greater than that of feed rate. Also from the empirical model, the preferable range of cutting parameters was obtained.

Experimental Study on Tool Wear in Cutting Titanium Alloy Ti6Al4V

2011 ◽  
Vol 239-242 ◽  
pp. 2011-2014
Author(s):  
Yue Feng Yuan ◽  
Wu Yi Chen ◽  
Wen Ying Zhang
Keyword(s):  
Titanium Alloy ◽  
Tool Wear ◽  
Tool Life ◽  
Linear Regression Analysis ◽  
Cutting Speed ◽  
Cutting Parameters ◽  
Aged Condition ◽  
Cutting Depth ◽  
Solution Treated ◽  
Titanium Alloy Ti6al4v

Tool wear experiments in turning titanium alloy Ti6Al4V in the solution-treated and aged condition were carried out; the influence rules of cutting parameters such as cutting speed, feed rate and cutting depth on the tool life were obtained. Experimental formula of tool wear was regressed based on multi-variable linear regression analysis, it could predict tool life under certain conditions.

Effect of cutting parameters on tool life during end milling of AISI 4340 under MQL condition

2022 ◽  
Vol ahead-of-print (ahead-of-print) ◽  
Author(s):  
Ahsana Aqilah Ahmad ◽  
Jaharah A. Ghani ◽  
Che Hassan Che Haron
Keyword(s):  
Tool Wear ◽  
Tool Life ◽  
Wear Mechanism ◽  
High Speed ◽  
End Milling ◽  
Cutting Speed ◽  
Cutting Parameters ◽  
Depth Of Cut ◽  
Content Type ◽  
Radial Depth

Purpose The purpose of this paper is to study the cutting performance of high-speed regime end milling of AISI 4340 by investigating the tool life and wear mechanism of steel using the minimum quantity lubrication (MQL) technique to deliver the cutting fluid. Design/methodology/approach The experiments were designed using Taguchi L9 orthogonal array with the parameters chosen: cutting speed (between 300 and 400 m/min), feed rate (between 0.15 and 0.3 mm/tooth), axial depth of cut (between 0.5 and 0.7 mm) and radial depth of cut (between 0.3 and 0.7 mm). Toolmaker microscope, optical microscope and Hitachi SU3500 Variable Pressure Scanning Electron Microscope used to measure tool wear progression and wear mechanism. Findings Cutting speed 65.36%, radial depth of cut 24.06% and feed rate 6.28% are the cutting parameters that contribute the most to the rate of tool life. The study of the tool wear mechanism revealed that the oxide layer was observed during lower and high cutting speeds. The former provides a cushion of the protective layer while later reduce the surface hardness of the coated tool Originality/value A high-speed regime is usually carried out in dry conditions which can shorten the tool life and accelerate the tool wear. Thus, this research is important as it investigates how the use of MQL and cutting parameters can prolong the usage of tool life and at the same time to achieve a sustainable manufacturing process.

Study on the Wear of Cutting-Tools Used in Dry Machining of Cu-10wt%Al-5wt%Ni-5wt%Fe Alloy

2021 ◽  
Vol 413 ◽  
pp. 194-200
Author(s):  
Marcos de Aguiar Guimarães ◽  
Givanildo Alves dos Santos ◽  
Mauricio S. Nascimento ◽  
Rogerio Teram ◽  
Vinicius Torres dos Santos ◽  
...  
Keyword(s):  
Tool Wear ◽  
Copper Alloys ◽  
Cutting Speed ◽  
Main Tool ◽  
Cutting Parameters ◽  
Lower Surface ◽  
Raw Material ◽  
Machining Process ◽  
Dry Machining ◽  
Aluminium Bronze

Aluminium bronze alloys are special copper alloys that have a machinability rate from 20 to 40% compared to free cutting brasses, so the cutting parameters and type of tools suitable for machining of these materials may be very different for other copper alloys. Also, due to the relative high costs of the raw material, the absence of contamination of the chips by cutting fluids improve its intrinsic resales value and encourage the use of machining process without coolant. The aim of this work is to evaluate the tool wear mechanisms in the finishing machining of the Cu-10wt%Al-5wt%Ni-5wt%Fe aluminium-bronze alloy with carbide and cermet inserts at different cutting speeds under dry machining condition. The turning of material showed lower surface roughness in higher speed conditions and better dimensional stability at lower speeds. It was observed the formation of continuous chips, but of little volume occupied. The scanning electron microscopy (SEM) and energy dispersive X-ray spectroscopy (EDS) analyses of tool wear show the adhesion as the main tool wear mechanism, followed by abrasion. At the lower cutting speed, the adhesion wears affected significantly the surface finish, reducing the tool life in comparison to the higher speeds.

Tool Life in High Speed Turning with Negative Rake Angle

2011 ◽  
Vol 264-265 ◽  
pp. 1009-1014 ◽  
Author(s):  
Erry Yulian Triblas Adesta ◽  
Muataz H.F. Al Hazza
Keyword(s):  
Tool Wear ◽  
Tool Life ◽  
High Speed ◽  
Cutting Speed ◽  
Cutting Parameters ◽  
Rake Angle ◽  
Turning Process ◽  
High Speed Cutting ◽  
Life Estimation ◽  
High Speed Turning

The present work studies some aspects of turning process applied on mild steel using cermets tools at high speed cutting (1000mm/min) by using negative rake angle (0 to-12). The influence of increasing the cutting speed and negative rake angle on flank tool wear, cutting forces, feeding forces and tool temperature were analyzed. The research studies and concentrates on the tool life estimation and the effect of the negative rake angle and higher cutting speed on tool life. It was found that the maximum tool life is obtained in (-6) rake angle for the cutting parameters.

Cutting Force, Cutting Temperature and Tool Wear in End Milling of Powder Metallurgy Nickel-Based Superalloy FGH95

2011 ◽  
Vol 188 ◽  
pp. 55-60
Author(s):  
J. Du ◽  
Zhan Qiang Liu
Keyword(s):  
Powder Metallurgy ◽  
Tool Wear ◽  
Cutting Force ◽  
End Milling ◽  
Cutting Temperature ◽  
Cutting Speed ◽  
High Strength ◽  
Cutting Parameters ◽  
Nickel Based Superalloy ◽  
Adhesion Wear

FGH95 is one kind of high-strength, thermal-resistant nickel-based superalloys fabricated by powder metallurgy (PM). It plays an increasingly important role in the development and manufacture of turbine discs. Due to the extreme toughness and work hardening characteristics of this kind of superalloy, the problem of machining FGH95 is one of ever-increasing magnitudes. This paper investigates the influence of cutting parameters on the cutting force, cutting temperature and tool wear during the end milling of PM nickel-based superalloy FGH95. The empirical formula for cutting force and cutting temperature of FGH95 are given out. Experimental results show that the cutting speed among milling parameters has the greatest influence on cutting forces and cutting temperatures. It is shown that the major tool wear mechanisms are combination interactions of abrasive wear, adhesion wear, micro-breakout and chipping.

scholarly journals Influence of Cutting Parameters on the Surface Quality of Two-Layer Sandwich Structures

Materials ◽  
2020 ◽  
Vol 13 (7) ◽  
pp. 1664
Author(s):  
Elżbieta Doluk ◽  
Anna Rudawska ◽  
Józef Kuczmaszewski ◽  
Paweł Pieśko
Keyword(s):  
Sandwich Structure ◽  
Sandwich Structures ◽  
Composite Layer ◽  
Cutting Speed ◽  
High Strength ◽  
Cutting Parameters ◽  
Carbon Composite ◽  
Machining Process ◽  
Machining Parameters ◽  
2024 Aluminum Alloy

Hybrid sandwich structures are more and more widely used in many industries. This is mainly due to their good properties. One of the limitations regarding the use of sandwich structures is their difficult processing. Therefore, it seems reasonable to determine the influence of cutting parameters and machining configuration on the characteristic defect (phase) formed at the boundary of the materials forming a hybrid sandwich structure. This study investigates the effects of layer orientations during milling and machining parameters such as the cutting speed Vc, the feed fz and the cutting width ae. The study is conducted on a two-layer sandwich structure composed of two materials: 2024 aluminum alloy and epoxy-carbon composite with 60% of high-strength carbon fibers. A statistical analysis is performed using the Statistica program. The results show that the change in the cutting parameters has a greater impact on the formation of a defect on the surface of samples when the machining process starts on the side of the composite rather than the metal. The highest defect value is obtained for the milling from the composite layer when the process is performed with the following cutting parameters: Vc = 300 m/min, fz = 0.08 mm/tooth, ae = 5 mm.

Sign in / Sign up

Export Citation Format

Share Document