Effects of thermal modification on the mechanical properties of the wood cell wall of soft wood: behavior of S2 cellulose microfibrils under tensile loading

2020 ◽  
Vol 55 (12) ◽  
pp. 5038-5047 ◽  
Author(s):  
Erina Kojima ◽  
Mariko Yamasaki ◽  
Koki Imaeda ◽  
Chang-Goo Lee ◽  
Takanori Sugimoto ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Cell Wall ◽  
Wood Cell Wall ◽  
Tensile Loading ◽  
Thermal Modification ◽  
Cellulose Microfibrils

scholarly journals Effect of Thermal Modification on the Nano-Mechanical Properties of the Wood Cell Wall and Waterborne Polyacrylic Coating

Forests ◽  
2020 ◽  
Vol 11 (12) ◽  
pp. 1247
Author(s):  
Yan Wu ◽  
Xinyu Wu ◽  
Feng Yang ◽  
Haiqiao Zhang ◽  
Xinhao Feng ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Contact Angle ◽  
Cell Wall ◽  
Wood Cell Wall ◽  
Pinus Massoniana ◽  
Treatment Temperature ◽  
Thermal Modification ◽  
Composition Analysis ◽  
Masson Pine ◽  
Heat Treated

Masson pine (Pinus massoniana Lamb.) samples were heat-treated at different treatment temperatures (150, 170, and 190 °C), and the nano-mechanical properties of the wood cell wall, which was coated with a waterborne polyacrylic (WPA) lacquer product, were compared. The elastic modulus (Er) and hardness (H) of wood cell wall and the coating were measured and characterized by nanoindentation, and the influencing factors of mechanical properties during thermal modification were investigated by chemical composition analysis, contact angle analysis, and colorimetric analysis. The results showed that with the increase in the heat treatment temperature, the contact angle of the water on the wood’s surface and the colorimetric difference increased, while the content of the cellulose and hemicelluloses decreased. After thermal modification of 190 °C, the Er and H of the wood cell wall increased by 13.9% and 17.6%, respectively, and the Er and H of the WPA coating applied to the wood decreased by 12.1% and 22.2%. The Er and H of the interface between the coating and wood were lower than those near the coating’s surface. The Er and H of the cell wall at the interface between the coating and wood were lower than those far away from the coating. This study was of great significance for understanding the binding mechanism between coating and wood cell walls and improving the finishing technology of the wood materials after thermal modification.

Comparison of mechanical properties of thermally modified wood at growth ring and cell wall level by means of instrumented indentation tests

Holzforschung ◽  
2009 ◽  
Vol 63 (4) ◽  
Author(s):  
Stefanie Stanzl-Tschegg ◽  
Wilfried Beikircher ◽  
Dieter Loidl
Keyword(s):  
Mechanical Properties ◽  
Cell Wall ◽  
Thermal Treatment ◽  
Mechanical Performance ◽  
Growth Ring ◽  
Beech Wood ◽  
Thermal Modification ◽  
Wood Structure ◽  
Instrumented Indentation ◽  
Indentation Tests

Abstract Thermal modification is a well established method to improve the dimensional stability and the durability for outdoor use of wood. Unfortunately, these improvements are usually accompanied with a deterioration of mechanical performance (e.g., reduced strength or higher brittleness). In contrast, our investigations of the hardness properties in the longitudinal direction of beech wood revealed a significant improvement with thermal modification. Furthermore, we applied instrumented indentation tests on different hierarchical levels of wood structure (growth ring and cell wall level) to gain closer insights on the mechanisms of thermal treatment of wood on mechanical properties. This approach provides a variety of mechanical data (e.g., elastic parameters, hardness parameters, and viscoelastic properties) from one single experiment. Investigations on the influence of thermal treatment on the mechanical properties of beech revealed similar trends on the growth ring as well as the on the cell wall level of the wood structure.

scholarly journals Enhancement of the physical and mechanical properties of wood using a novel organo-montmorillonite/hyperbranched polyacrylate emulsion

Holzforschung ◽  
2020 ◽  
Vol 0 (0) ◽  
Author(s):  
Jianfeng Xu ◽  
Xiaoyan Li ◽  
Ling Long ◽  
Ru Liu
Keyword(s):  
Mechanical Properties ◽  
Cell Wall ◽  
Pinus Radiata ◽  
Wood Sample ◽  
Wood Cell Wall ◽  
Physical And Mechanical Properties ◽  
Radiata Pine ◽  
Compact Structure ◽  
Populus Cathayana ◽  
Modified Wood

AbstractIn this work, a novel waterborne hyperbranched polyacrylate (HBPA) dispersed organo-montmorillonite (OMMT) emulsion was synthesized and used for the treatment of wood in a vacuum environment in order to enhance the physical and mechanical properties of the wood. The sapwood of Cathay poplar (Populus cathayana Rehd.) and Radiata pine (Pinus radiata D.Don) were used as the samples for experimentation. The results showed that the physical and mechanical properties of the wood improved significantly due to the successful penetration of the OMMT and HBPA into the wood cell wall. From it was also observed that OMET completely exfoliated from the HBPA matrix and formed a hydrophobic film covering on the inside walls of the cell lumen. Further, it was observed that the poplar sample displayed better mechanical properties than the pine sample because the pine has a more compact structure when compared to poplar and contains rosin. Furthermore, it was also observed that the mechanical properties of the modified wood sample gradually improved with an increase in the concentration of the emulsion. However, excessive concentration (>4 wt%) did not lead to further improvement.

scholarly journals Microstructure of thermally modified radiata pine wood

BioResources ◽  
2020 ◽  
Vol 16 (1) ◽  
pp. 1523-1533
Author(s):  
José Luis Cabezas-Romero ◽  
Linette Salvo-Sepúlveda ◽  
Helga Contreras-Moraga ◽  
Natalia Pérez-Peña ◽  
Víctor Sepúlveda-Villarroel ◽  
...  
Keyword(s):  
Cell Wall ◽  
Wood Cell Wall ◽  
Morphological Changes ◽  
Untreated Wood ◽  
Radiata Pine ◽  
Treatment Temperature ◽  
Thermal Modification ◽  
Modification Process ◽  
Potential Alternative ◽  
Two Temperatures

The thermal modification of wood is a potential alternative method for improving wood dimensional stability and increasing the resistance of wood to decay. However, during thermal modification, morphological changes occur within the microstructure of the cell, and these confer different properties to the wood. This study investigated the effects of the thermal modification process on the microstructure of radiata pine juvenile wood. Therefore, anatomical measurements were performed via optical microscopy in selected earlywood and latewood samples after each treatment, and the results were compared to untreated wood samples. In this study, two temperatures (190 °C and 210 °C) were considered for the thermal modification process. The results showed that the level of temperature of modification affected to microstructure of cell wall. The cell wall thickness decreased as treatment temperature increased, whereas the average lumen diameter increased slightly as temperature increased. Thermally modified radiata pine showed signs of damage (cracks, broken cells and deformations in the wood cell wall). The proportion of destroyed area increased as temperature increased, and significant differences were evident for the thermal treatment at 210 °C.

scholarly journals The Structure and Plastic Properties of the Cell Wall of Nitella in Relation to Extension Growth

1966 ◽  
Vol 19 (3) ◽  
pp. 439 ◽  
Author(s):  
MC Probine ◽  
NF Barber
Keyword(s):  
Mechanical Properties ◽  
Cell Wall ◽  
Cell Growth ◽  
Elastic Properties ◽  
Cell Shape ◽  
Cellulose Microfibrils ◽  
Theoretical Treatment ◽  
Plastic Properties ◽  
Growing Cell ◽  
Plastic Matrix

The internodal cells of Nitella opaca L. have been used in earlier studies to assess the part which mechanical properties of the wall may play in the control of cell growth (Probine and Preston 1962). The wall is mechanically anisotropic in both its plastic and elastic properties, and it is shown in this paper by an approximate theoretical treatment that a mat of cellulose microfibrils, embedded in a plastic matrix and having a distribution in the plane of the wall like that observed in Nitella, would lead to longitUdinal and transverse plastic extensions in the ratio observed in the growing cell. Factors which would affect cell shape are discussed.

scholarly journals The Implication of Benzene–Ethanol Extractive on Mechanical Properties of Waterborne Coating and Wood Cell Wall by Nanoindentation

Coatings ◽  
2019 ◽  
Vol 9 (7) ◽  
pp. 449 ◽  
Author(s):  
Yan Wu ◽  
Yingchun Sun ◽  
Feng Yang ◽  
Haiqiao Zhang ◽  
Yajing Wang
Keyword(s):  
Mechanical Properties ◽  
Cell Wall ◽  
Wood Surface ◽  
Cell Walls ◽  
Wood Cell Wall ◽  
Coating Layer ◽  
Waterborne Coating ◽  
Average Value ◽  
Wood Surfaces ◽  
Extraction Treatment

The waterborne coating uses water as its solvent, which will partially dissolve wood extractives when it is applied to wood surfaces. This influences both the coating curing process and the mechanical properties of the cured coating. To investigate these influences, the mechanical properties of waterborne polyacrylic coating on control and extractive-free wood surfaces were investigated by nanoindentation. Reductions to elastic modulus (Er) and hardness (H) of the coating layer was observed in the wood cell walls adjacent to or away from coating layers. Extraction treatment resulted in significant decrease of the Er and H of the coating layer on extractive-free wood surface comparing with control wood, but the values slightly increased for extractive-free wood cell walls compared to a control. Er and H of coating in wood cell lumen were higher than the average value of coating layer on wood surface in both the control and extractive-free wood. The Er of wood cell wall without coating filled in lumen was significantly higher than those of filling with coating. However, there was no distinct difference of H. The Er and H of CCML in extractive-free wood were 15% and 6% lower than those in control ones, respectively.

Sign in / Sign up

Export Citation Format

Share Document