scholarly journals Creep behavior of cemented sand investigated under cyclic loading

2021 ◽  
Vol 80 (23) ◽  
Author(s):  
Kuang-Tsung Chang ◽  
Kevin Zeh-Zon Lee ◽  
Po-Tsun Yeh ◽  
Chia-Ming Chang ◽  
Jin-Yi Yu
Keyword(s):  
Stress State ◽  
Cyclic Loading ◽  
Creep Strain ◽  
Stress Ratio ◽  
Groundwater Table ◽  
Mean Stress ◽  
Cyclic Variation ◽  
Creep Failure ◽  
Cemented Sand ◽  
Deviator Stress

AbstractThe influence of stress state on the creep behavior of an artificial cemented sand resembling soft rocks was evaluated. The stress state was characterized by a mean stress and a stress ratio. The cyclic stress-induced creep test was adopted in this study, where the cyclic loading involved a constant deviator stress and a cyclic mean stress (or confining pressure) of the same amplitude and period; the test indicated similar trends as the conventional creep test with a shorter time to creep failure at less creep strain. Results showed that when the creep strain is large enough, the greater the creep strain accumulates, the smaller is the post-creep strength. Under the same number of cyclic loads, with the same stress ratio, the creep strain and the steady-state strain rate in the secondary creep stage increase with increasing mean stress; with the same mean stress, the two said parameters also increase with increasing stress ratio. It was also found that the time to reach creep failure decreases with decreasing mean stress and increasing stress ratio. The stress ratio is proposed to account for the tendency of a stress state to cause failure, and the cyclic variation of mean stress, which is equivalent to the effective mean stress with pore water pressure being zero in the tests conducted, reflects the effective stress state of a geomaterial under fluctuations of groundwater table. Under a fixed deviator stress, a soft porous geomaterial subjected to cyclic variation of effective mean stress may yield contraction and could lead to failure if the stress ratio is high. The findings can help explain the mechanism of ground subsidence or slope failure subjected to cyclic fluctuations of groundwater table.

The Stress-Strain Behaviors of High Density Aluminum Foam under Monotonic and Cyclic Loading

2013 ◽  
Vol 464 ◽  
pp. 69-72 ◽  
Author(s):  
Yu Jie Liu ◽  
Bin Qiang
Keyword(s):  
Cyclic Loading ◽  
Aluminum Foam ◽  
Stress Ratio ◽  
High Density ◽  
Mean Stress ◽  
Stress Strain ◽  
Compressive Response ◽  
Ratcheting Strain ◽  
Tension Response ◽  
Stress Cycling

The stress-strain behaviors were investigated by monotonic and cyclic stressing tests for high density aluminum foam at room temperature. The cyclic accumulations of deformation for the material were measured in varied loading levels. The effects of mean stress and stress ratio on the ratcheting strain were discussed. The experimental results show that tension response is different from the compressive response. There is obvious cyclic accumulations of deformation (i.e., ratcheting effect) under compression-compression cyclic loading even if the holistic stress-strain response is linear. And the ratcheting of aluminum foam greatly depends on mean stress and stress ratio in asymmetric stress cycling. The experimental rules and data are significant for constitutive description and numerical simulation of aluminum foam.

Comparative study of the effective parameters on residual stress relaxation in welded aluminum plates under cyclic loading

2020 ◽  
Vol 21 (5) ◽  
pp. 505
Author(s):  
Yousef Ghaderi Dehkordi ◽  
Ali Pourkamali Anaraki ◽  
Amir Reza Shahani
Keyword(s):  
Residual Stress ◽  
Cyclic Loading ◽  
Stress Relaxation ◽  
Stress Amplitude ◽  
Cyclic Plasticity ◽  
Mean Stress ◽  
Effective Parameters ◽  
Perfect Plasticity ◽  
Residual Stress Relaxation ◽  
Aluminum Plates

The prediction of residual stress relaxation is essential to assess the safety of welded components. This paper aims to study the influence of various effective parameters on residual stress relaxation under cyclic loading. In this regard, a 3D finite element modeling is performed to determine the residual stress in welded aluminum plates. The accuracy of this analysis is verified through experiment. To study the plasticity effect on stress relaxation, two plasticity models are implemented: perfect plasticity and combined isotropic-kinematic hardening. Hence, cyclic plasticity characterization of the material is specified by low cycle fatigue tests. It is found that the perfect plasticity leads to greater stress relaxation. In order to propose an accurate model to compute the residual stress relaxation, the Taguchi L18 array with four 3-level factors and one 6-level is employed. Using statistical analysis, the order of factors based on their effect on stress relaxation is determined as mean stress, stress amplitude, initial residual stress, and number of cycles. In addition, the stress relaxation increases with an increase in mean stress and stress amplitude.

Uniaxial Ratcheting and Low-Cycle Fatigue Failure of U75V Rail Steel

2016 ◽  
Vol 853 ◽  
pp. 246-250 ◽  
Author(s):  
Tao Fang ◽  
Qian Hua Kan ◽  
Guo Zheng Kang ◽  
Wen Yi Yan
Keyword(s):  
Fatigue Life ◽  
Strain Amplitude ◽  
Stress Ratio ◽  
Stress Amplitude ◽  
Rail Steel ◽  
Low Cycle Fatigue ◽  
Mean Stress ◽  
Cycle Fatigue ◽  
Ratcheting Strain ◽  
Cyclic Straining

Experiments on U75V rail steel were carried out to investigate the cyclic feature, ratcheting behavior and low-cycle fatigue under both strain- and stress-controlled loadings at room temperature. It was found that U75V rail steel shows strain amplitude dependent cyclic softening feature, i.e., the responded stress amplitude under strain-controlled decreases with the increasing number of cycles and reaches a stable value after about 20th cycle. Ratcheting strain increases with an increasing stress amplitude and mean stress, except for stress ratio, and the ratcheting strain in failure also increases with an increasing stress amplitude, mean stress and stress ratio. The low-cycle fatigue lives under cyclic straining decrease linearly with an increasing strain amplitude, the fatigue lives under cyclic stressing decrease with an increasing mean stress except for zero mean stress, and decrease with an increasing stress amplitude. Ratcheting behavior with a high mean stress reduces fatigue life of rail steel by comparing fatigue lives under stress cycling with those under strain cycling. Research findings are helpful to evaluate fatigue life of U75V rail steel in the railways with passenger and freight traffic.

Small strain stiffness for granite residual soil: effect of stress ratio

2021 ◽  
Author(s):  
Xianwei Zhang ◽  
Xinyu Liu ◽  
Lingwei Kong ◽  
Gang Wang ◽  
Cheng Chen
Keyword(s):  
Stress Ratio ◽  
Small Strain ◽  
Residual Soil ◽  
Resonant Column ◽  
Residual Soils ◽  
Column Tests ◽  
Small Strain Stiffness ◽  
Deviator Stress ◽  
Granite Residual Soil ◽  
Stress Ratios

Most previous studies have focused on the small strain stiffness of sedimentary soil while little attention has been given to residual soils with different properties. Most studies also neglected the effects of the deviator stress, which is extensively involved in civil engineering. This note considers the effects of the deviator stress on the small-strain stiffness of natural granite residual soil (GRS) as established from resonant column tests performed under various stress ratios. Although increasing the stress ratio results in a greater maximum shear modulus for both natural and remolded residual soils, remolded soil is more sensitive to changes in the stress ratio, which highlights the effects of soil cementation. The data herein offers new insights to understand the stiffness of residual soil and other weathered geomaterials.

Fatigue and creep failure of organic fibres subjected to cyclic loading

1986 ◽  
Vol 5 (11) ◽  
pp. 1101-1103 ◽  
Author(s):  
A. R. Bunsell ◽  
Ch. Oudet ◽  
J. Ch. Veve
Keyword(s):  
Cyclic Loading ◽  
Creep Failure

scholarly journals MODELLING CHLORIDE DIFFUSION IN CONCRETE WITH INFLUENCE OF CONCRETE STRESS STATE

2017 ◽  
Vol 23 (7) ◽  
pp. 955-965 ◽  
Author(s):  
Jian WANG ◽  
Pui-Lam NG ◽  
Weishan WANG ◽  
Jinsheng DU ◽  
Jianyong SONG
Keyword(s):  
Experimental Data ◽  
Diffusion Coefficient ◽  
Stress State ◽  
Diffusion Model ◽  
Stress Ratio ◽  
Chloride Diffusion ◽  
Influence Coefficient ◽  
Chloride Diffusion Coefficient ◽  
Stress Influence ◽  
Concrete Stress

Under coastal or marine conditions, chloride erosion is the major accelerating factor of reinforcement corrosion. Therefore, it is of vital importance to investigate the chloride diffusion model. Research reveals that the concrete stress state has great influence on chloride diffusion; therefore a stress influence coefficient was incorporated in chloride diffusion coefficient model by many researchers. By referring to the experimental data from eight different researchers, the law between stress influence coefficient and concrete stress ratio is studied in detail, and equations relating the stress influence coefficient with the concrete stress ratio are established. Compared with three typical existing groups of equations, it is found that the proposed equations give the most accurate estim.ation of the stress influence coefficient. Hence, the proposed equations can be adopted to improve the valuation of chloride diffusion coefficient, and a modified chloride diffusion model is put forward. Three groups of experimental data are used to validate the modified chloride diffusion model, which is shown to be reasonable and having high prediction accuracy.

scholarly journals Creep Rupture and Permeability Evolution in High Temperature Heat-Treated Sandstone Containing Pre-Existing Twin Flaws

Energies ◽  
2021 ◽  
Vol 14 (19) ◽  
pp. 6362
Author(s):  
Sheng-Qi Yang ◽  
Jin-Zhou Tang ◽  
Derek Elsworth
Keyword(s):  
Creep Strain ◽  
Stress Level ◽  
Stress Ratio ◽  
Deviatoric Stress ◽  
Threshold Temperature ◽  
Critical Threshold ◽  
Plastic Strains ◽  
Permeability Evolution ◽  
Heat Treated ◽  
Pre Treatment

Utilizing underground coal gasification cavities for carbon capture and sequestration provides a potentially economic and sustainable solution to a vexing environmental and energy problem. The thermal influence on creep properties and long-term permeability evolution around the underground gasification chamber is a key issue in UCG-CCS operation in containing fugitive emissions. We complete multi-step loading and unloading creep tests with permeability measurement at confining stresses of 30 MPa on pre-cracked sandstone specimens thermally heat-treated to 250, 500, 750 and 1000 °C. Observations indicate a critical threshold temperature of 500 °C required to initiate thermally-induced cracks with subsequent strength reduction occurring at 750 °C. Comparison of histories of creep, visco-elastic and visco-plastic strains highlight the existence of a strain jump at a certain deviatoric stress level—where the intervening rock bridge between the twin starter-cracks is eliminated. As the deviatoric stress level increases, the visco-plastic strains make up an important composition of total creep strain, especially for specimens pre-treated at higher temperatures, and the development of the visco-plastic strain leads to the time-dependent failure of the rock. The thermal pre-treatment produces thermal cracks with their closure resulting in increased instantaneous elastic strains and instantaneous plastic strains. With increasing stress ratio, the steady-state creep rates increase slowly before the failure stress ratio but rise suddenly over the final stress ratio to failure. However, the pre-treatment temperature has no clear and apparent influence on steady creep strain rates. Rock specimens subject to higher pre-treatment temperatures exhibit higher permeabilities. The pre-existing cracks close under compression with a coplanar shear crack propagating from the starter-cracks and ultimately linking these formerly separate cracks. In addition, it is clear that the specimens pre-treated at higher temperatures accommodate greater damage.

scholarly journals Fatigue Life Prediction of Rolling Bearings Based on Modified SWT Mean Stress Correction

2020 ◽  
Author(s):  
Aodi Yu ◽  
Hong-Zhong Huang ◽  
Yan-Feng Li ◽  
He Li ◽  
Ying Zeng
Keyword(s):  
Fatigue Life ◽  
Life Prediction ◽  
Stress Ratio ◽  
Prediction Models ◽  
Great Influence ◽  
Sensitivity Coefficient ◽  
Model Verification ◽  
Mean Stress ◽  
Test Results ◽  
Rolling Bearings

Abstract Mean stress has a great influence on fatigue life, commonly used stress-based life prediction models can only fit the test results of fatigue life under specific stress ratio or mean stress but cannot describe the effect of stress ratio or mean stress on fatigue life. Smith, Watson and Topper (SWT) proposed a simple mean stress correction criterion. However, the SWT model regards the sensitivity coefficient of all materials to mean stress as 0.5, which will lead to inaccurate predictions for materials with a sensitivity coefficient not equal to 0.5. In this paper, considering the sensitivity of different materials to mean stresses, compensation factor is introduced to modify the SWT model, and several sets of experimental data are used for model verification. Then, the proposed model is applied to fatigue life predictions of rolling bearings, and the results of proposed method are compared with test results to verify its accuracy.

Sign in / Sign up

Export Citation Format

Share Document