scholarly journals Ag2S nanoparticles decorated graphene as a selective chemical sensor for acetone working at room temperature

2021 ◽  
pp. 150201
Author(s):  
A-Rang Jang ◽  
Ji Eun Lim ◽  
Seunghun Jang ◽  
Myung Hyun Kang ◽  
Geonhee Lee ◽  
...  
2021 ◽  
Vol 10 (1) ◽  
pp. 330-369
Author(s):  
Norizan M. Nurazzi ◽  
Norli Abdullah ◽  
Siti Z. N. Demon ◽  
Norhana A. Halim ◽  
Ahmad F. M. Azmi ◽  
...  

Abstract Graphene is a single-atom-thick sheet of sp2 hybridized carbon atoms that are packed in a hexagonal honeycomb crystalline structure. This promising structure has endowed graphene with advantages in electrical, thermal, and mechanical properties such as room-temperature quantum Hall effect, long-range ballistic transport with around 10 times higher electron mobility than in Si and thermal conductivity in the order of 5,000 W/mK, and high electron mobility at room temperature (250,000 cm2/V s). Another promising characteristic of graphene is large surface area (2,630 m2/g) which has emerged so far with its utilization as novel electronic devices especially for ultrasensitive chemical sensor and reinforcement for the structural component applications. The application of graphene is challenged by concerns of synthesis techniques, and the modifications involved to improve the usability of graphene have attracted extensive attention. Therefore, in this review, the research progress conducted in the previous decades with graphene and its derivatives for chemical detection and the novelty in performance enhancement of the chemical sensor towards the specific gases and their mechanism have been reviewed. The challenges faced by the current graphene-based sensors along with some of the probable solutions and their future improvements are also being included.


2016 ◽  
Vol 811 ◽  
pp. 74-80 ◽  
Author(s):  
Mohammed M. Rahman ◽  
Hadi M. Marwani ◽  
Abdelmohsen A. Alshehri ◽  
Hassan A. Albar ◽  
Juan Bisquert ◽  
...  

2003 ◽  
Vol 787 ◽  
Author(s):  
Franz L. Dickert ◽  
Peter A. Lieberzeit ◽  
Sylwia Gazda-Miarecka ◽  
Konstantin Halikias ◽  
Roland Bindeus

ABSTRACTMolecular imprinting leads to functional polymers that are capable to incorporate the template used and thus lead to selective chemical sensor systems when combined with a suitable transducer. Benzene and xylene can e.g. be distinguished with a selectivity factor of nearly ten using mass-sensitive devices such as QCM and SAW, although they both contain an aromatic system and differ only by the methyl groups. Sensing materials are further tuned by using binary mixtures as templates. When analyzing polycyclic aromatic hydrocarbons (PAH) by fluorescence and QCM measurements, the sensitivity is substantially increased if a second template molecule is applied as a porogen. Capacitive sensor measurements on polymers imprinted with microorganisms, such as yeasts, show substantial sensor responses due to highly selective inclusion compared with a non-functionalised surface yielding only negligible effects.


2006 ◽  
Vol 921 ◽  
Author(s):  
Shawn S Coffee ◽  
Wyatt A Winkenwerder ◽  
Scott K Stanley ◽  
Shahrjerdi Davood ◽  
Sanjay K Banerjee ◽  
...  

AbstractGermanium nanoparticle nucleation was studied in organized arrays on HfO2 using a SiO2 thin film mask with ~20-24 nm pores and a 6×1010 cm-2 pore density. Poly(styrene-b-methyl methacrylate) diblock copolymer was employed to pattern the SiO2 film. Hot wire chemical vapor deposition produced Ge nanoparticles using 4-19 monolayer Ge exposures. By seeding adatoms on HfO2 at room temperature before growth and varying growth temperatures between 725-800 K, nanoparticle size was demonstrated to be limited by Ge etching of SiO2 pore walls.


Talanta ◽  
2017 ◽  
Vol 170 ◽  
pp. 215-223 ◽  
Author(s):  
Mohammed M. Rahman ◽  
M.M. Alam ◽  
Abdullah M. Asiri ◽  
M.A. Islam

2001 ◽  
Author(s):  
Jack G. Zhou ◽  
Feng Wang

Abstract Most technologies used in fabrication of MEMS involve very sophisticated and expensive processes, which limit the application of MEMS greatly. This paper presents our research on a new manufacturing technology named Selective Chemical Liquid Deposition for Mini-structures and Microsystems SCLD-MSMS. In SCLD-MEMS, small droplets of solution or liquid reactant are ejected from a nozzle at room temperature, the droplets decompose or react with each other after impinging upon a hot substrate, the reacted solid products will then deposit on the substrate. By controlling the droplet size, the flow rate, the motion of the nozzle, and the temperature of the substrate, as well as other process parameters, a desired 3-D microstructure of deposited material can be formed through layer-by-layer scanning technique. The working principle and some experiment results are discussed in this paper.


Small ◽  
2005 ◽  
Vol 1 (6) ◽  
pp. 636-639 ◽  
Author(s):  
Frédéric Goettmann ◽  
Audrey Moores ◽  
Cédric Boissière ◽  
Pascal Le Floch ◽  
Clément Sanchez

Sign in / Sign up

Export Citation Format

Share Document