A simplified CFD model to describe fluid dynamics, mass transport and breakthrough curves performance in cryogel supports for chromatographic separation

2021 ◽  
Author(s):  
Jamille C. Coimbra ◽  
Marcio A. Martins ◽  
Luis A. Minim
Keyword(s):  
Fluid Dynamics ◽  
Mass Transport ◽  
Chromatographic Separation ◽  
Breakthrough Curves ◽  
Cfd Model

Effects of Over Fire Air on the Combustion and NOx Emission Characteristics of a 600 MW Opposed Swirling Fired Boiler

2012 ◽  
Vol 512-515 ◽  
pp. 2135-2142 ◽  
Author(s):  
Yu Peng Wu ◽  
Zhi Yong Wen ◽  
Yue Liang Shen ◽  
Qing Yan Fang ◽  
Cheng Zhang ◽  
...  
Keyword(s):  
Fluid Dynamics ◽  
Experimental Data ◽  
Empirical Method ◽  
Nox Emission ◽  
Emission Characteristics ◽  
Cfd Model ◽  
Nitrogen Release ◽  
Computational Fluid Dynamics Cfd ◽  
Low Nox Emission

A computational fluid dynamics (CFD) model of a 600 MW opposed swirling coal-fired utility boiler has been established. The chemical percolation devolatilization (CPD) model, instead of an empirical method, has been adapted to predict the nitrogen release during the devolatilization. The current CFD model has been validated by comparing the simulated results with the experimental data obtained from the boiler for case study. The validated CFD model is then applied to study the effects of ratio of over fire air (OFA) on the combustion and nitrogen oxides (NOx) emission characteristics. It is found that, with increasing the ratio of OFA, the carbon content in fly ash increases linearly, and the NOx emission reduces largely. The OFA ratio of 30% is optimal for both high burnout of pulverized coal and low NOx emission. The present study provides helpful information for understanding and optimizing the combustion of the studied boiler

scholarly journals Design of Road-Side Barriers to Mitigate Air Pollution near Roads

2021 ◽  
Vol 11 (5) ◽  
pp. 2391
Author(s):  
Jose I. Huertas ◽  
Javier E. Aguirre ◽  
Omar D. Lopez Mejia ◽  
Cristian H. Lopez
Keyword(s):  
Fluid Dynamics ◽  
Air Pollution ◽  
Computational Fluid Dynamics ◽  
Sulfur Hexafluoride ◽  
Computational Domain ◽  
Cfd Model ◽  
Near Surface ◽  
The Road ◽  
Pollutant Concentrations ◽  
Highly Correlated

The effects of using solid barriers on the dispersion of air pollutants emitted from the traffic of vehicles on roads located over flat areas were quantified, aiming to identify the geometry that maximizes the mitigation effect of air pollution near the road at the lowest barrier cost. Toward that end, a near road Computational Fluid Dynamics (NR-CFD) model that simulates the dispersion phenomena occurring in the near-surface atmosphere (<250 m high) in a small computational domain (<1 km long), via Computational Fluid Dynamics (CFD) was used. Results from the NR-CFD model were highly correlated (R2 > 0.96) with the sulfur hexafluoride (SF6) concentrations measured by the US-National Oceanic and Atmospheric Administration (US-NOAA) in 2008 downwind a line source emission, for the case of a 6m near road solid straight barrier and for the case without any barrier. Then, the effects of different geometries, sizes, and locations were considered. Results showed that, under all barrier configurations, the normalized pollutant concentrations downwind the barrier are highly correlated (R2 > 0.86) to the concentrations observed without barrier. The best cost-effective configuration was observed with a quarter-ellipse barrier geometry with a height equivalent to 15% of the road width and located at the road edge, where the pollutant concentrations were 76% lower than the ones observed without any barrier.

Validation of a Computationally Efficient Computational Fluid Dynamics (CFD) Model for Industrial Bubble Column Bioreactors

2014 ◽  
Vol 53 (37) ◽  
pp. 14526-14543 ◽  
Author(s):  
Dale D. McClure ◽  
Hannah Norris ◽  
John M. Kavanagh ◽  
David F. Fletcher ◽  
Geoffrey W. Barton
Keyword(s):  
Fluid Dynamics ◽  
Computational Fluid Dynamics ◽  
Bubble Column ◽  
Cfd Model ◽  
Computationally Efficient ◽  
Computational Fluid Dynamics Cfd

scholarly journals Journal Bearing: An Integrated CFD-Analytical Approach for the Estimation of the Trajectory and Equilibrium Position

2020 ◽  
Vol 10 (23) ◽  
pp. 8573
Author(s):  
Franco Concli
Keyword(s):  
Fluid Dynamics ◽  
Computational Fluid Dynamics ◽  
Pressure Distribution ◽  
Equilibrium Position ◽  
Analytical Approach ◽  
Journal Bearing ◽  
Cfd Model ◽  
Cavitation Model ◽  
Computational Fluid Dynamics Cfd ◽  
The Mathematical Model

For decades, journal bearings have been designed based on the half-Sommerfeld equations. The semi-analytical solution of the conservation equations for mass and momentum leads to the pressure distribution along the journal. However, this approach admits negative values for the pressure, phenomenon without experimental evidence. To overcome this, negative values of the pressure are artificially substituted with the vaporization pressure. This hypothesis leads to reasonable results, even if for a deeper understanding of the physics behind the lubrication and the supporting effects, cavitation should be considered and included in the mathematical model. In a previous paper, the author has already shown the capability of computational fluid dynamics to accurately reproduce the experimental evidences including the Kunz cavitation model in the calculations. The computational fluid dynamics (CFD) results were compared in terms of pressure distribution with experimental data coming from different configurations. The CFD model was coupled with an analytical approach in order to calculate the equilibrium position and the trajectory of the journal. Specifically, the approach was used to study a bearing that was designed to operate within tight tolerances and speeds up to almost 30,000 rpm for operation in a gearbox.

An Improved Computational Fluid Dynamics (CFD) Model for Erosion Prediction in Oil and Gas Industry Applications

2014 ◽  
Author(s):  
Deval Pandya ◽  
Brian Dennis ◽  
Ronnie Russell
Keyword(s):  
Fluid Dynamics ◽  
Computational Fluid Dynamics ◽  
Surface Velocity ◽  
Particle Model ◽  
Model Parameters ◽  
Cfd Model ◽  
Erosion Model ◽  
Erosion Prediction ◽  
Erosion Models ◽  
Computational Fluid Dynamics Cfd

In recent years, the study of flow-induced erosion phenomena has gained interest as erosion has a direct influence on the life, reliability and safety of equipment. Particularly significant erosion can occur inside the drilling tool components caused by the low particle loading (<10%) in the drilling fluid. Due to the difficulty and cost of conducting experiments, significant efforts have been invested in numerical predictive tools to understand and mitigate erosion within drilling tools. Computational fluid dynamics (CFD) is becoming a powerful tool to predict complex flow-erosion and a cost-effective method to re-design drilling equipment for mitigating erosion. Existing CFD-based erosion models predict erosion regions fairly accurately, but these models have poor reliability when it comes to quantitative predictions. In many cases, the error can be greater than an order of magnitude. The present study focuses on development of an improved CFD-erosion model for predicting the qualitative as well as the quantitative aspects of erosion. A finite-volume based CFD-erosion model was developed using a commercially available CFD code. The CFD model involves fluid flow and turbulence modeling, particle tracking, and application of existing empirical erosion models. All parameters like surface velocity, particle concentration, particle volume fraction, etc., used in empirical erosion equations are obtained through CFD analysis. CFD modeling parameters like numerical schemes, turbulence models, near-wall treatments, grid strategy and discrete particle model parameters were investigated in detail to develop guidelines for erosion prediction. As part of this effort, the effect of computed results showed good qualitative and quantitative agreement for the benchmark case of flow through an elbow at different flow rates and particle sizes. This paper proposes a new/modified erosion model. The combination of an improved CFD methodology and a new erosion model provides a novel computational approach that accurately predicts the location and magnitude of erosion. Reliable predictive methodology can help improve designs of downhole equipment to mitigate erosion risk as well as provide guidance on repair and maintenance intervals. This will eventually lead to improvement in the reliability and safety of downhole tool operation.

scholarly journals A Combined Computational Fluid Dynamics and Arterial Spin Labeling MRI Modeling Strategy to Quantify Patient-Specific Cerebral Hemodynamics in Cerebrovascular Occlusive Disease

2021 ◽  
Vol 9 ◽  
Author(s):  
Jonas Schollenberger ◽  
Nicholas H. Osborne ◽  
Luis Hernandez-Garcia ◽  
C. Alberto Figueroa
Keyword(s):  
Fluid Dynamics ◽  
Computational Fluid Dynamics ◽  
Blood Supply ◽  
Arterial Spin Labeling ◽  
Spin Labeling ◽  
Cerebral Hemodynamics ◽  
Occlusive Disease ◽  
Patient Specific ◽  
Cfd Model ◽  
Cerebrovascular Occlusive Disease

Cerebral hemodynamics in the presence of cerebrovascular occlusive disease (CVOD) are influenced by the anatomy of the intracranial arteries, the degree of stenosis, the patency of collateral pathways, and the condition of the cerebral microvasculature. Accurate characterization of cerebral hemodynamics is a challenging problem. In this work, we present a strategy to quantify cerebral hemodynamics using computational fluid dynamics (CFD) in combination with arterial spin labeling MRI (ASL). First, we calibrated patient-specific CFD outflow boundary conditions using ASL-derived flow splits in the Circle of Willis. Following, we validated the calibrated CFD model by evaluating the fractional blood supply from the main neck arteries to the vascular territories using Lagrangian particle tracking and comparing the results against vessel-selective ASL (VS-ASL). Finally, the feasibility and capability of our proposed method were demonstrated in two patients with CVOD and a healthy control subject. We showed that the calibrated CFD model accurately reproduced the fractional blood supply to the vascular territories, as obtained from VS-ASL. The two patients revealed significant differences in pressure drop over the stenosis, collateral flow, and resistance of the distal vasculature, despite similar degrees of clinical stenosis severity. Our results demonstrated the advantages of a patient-specific CFD analysis for assessing the hemodynamic impact of stenosis.

Numerical Investigation of Natural Convection in a Mono-Span Greenhouse

2012 ◽  
Author(s):  
Sunita Kruger ◽  
Leon Pretorius
Keyword(s):  
Fluid Dynamics ◽  
Computational Fluid Dynamics ◽  
Natural Convection ◽  
Pitch Angle ◽  
Design Tool ◽  
Design Parameters ◽  
Two Dimensional ◽  
Cfd Model ◽  
Indoor Climate ◽  
Contour Plots

In this paper, the use of computational fluid dynamics is evaluated as a design tool to investigate the indoor climate of a confined greenhouse. The finite volume method using polyhedral cells is used to solve the governing mass, momentum and energy equations. Natural convection in a cavity corresponding to a mono-span venlo-type greenhouse is numerically investigated using Computational Fluid Dynamics. The CFD model is designed so as to simulate the climate above a plant canopy in an actual multi-span greenhouse heated by solar radiation. The aim of this paper is to investigate the influence of various design parameters such as pitch angle and roof asymmetry and on the velocity and temperature patterns inside a confined single span greenhouse heated from below. In the study reported in this paper a two-dimensional CFD model was generated for the mono-span venlo-type greenhouse, and a mesh sensitivity analysis was conducted to determine the mesh independence of the solution. Similar two-dimensional flow patterns were observed in the obtained CFD results as the experimental results reported by Lamrani et al [2]. The CFD model was then modified and used to explore the effect of roof pitch angle and roof asymmetry at floor level on the development of the flow and temperature patterns inside the cavity for various Rayleigh numbers. Results are presented in the form of vector and contour plots. It was found that considerable temperature and velocity gradients were observed in the centre of the greenhouse for each case in the first 40mm above the ground, as well as in the last 24mm close to the roof. Results also indicated that the Rayleigh number did not have a significant impact on the flow and temperature patterns inside the greenhouse, although roof angle and asymmetry did. The current results demonstrate the importance of CFD as a design tool in the case of greenhouse design.

Experimentally Validated Computational Fluid Dynamics Model for Data Center With Active Tiles

2018 ◽  
Vol 140 (1) ◽  
Author(s):  
Jayati Athavale ◽  
Yogendra Joshi ◽  
Minami Yoda
Keyword(s):  
Fluid Dynamics ◽  
Computational Fluid Dynamics ◽  
Flow Rate ◽  
Data Center ◽  
Hot Spot ◽  
Volume Flow Rate ◽  
Optimal Number ◽  
Inlet Temperature ◽  
Cfd Model ◽  
Level Model

Abstract This paper presents an experimentally validated room-level computational fluid dynamics (CFD) model for raised-floor data center configurations employing active tiles. Active tiles are perforated floor tiles with integrated fans, which increase the local volume flow rate by redistributing the cold air supplied by the computer room air conditioning (CRAC) unit to the under-floor plenum. The numerical model of the data center room consists of one cold aisle with 12 racks arranged on both sides and three CRAC units sited around the periphery of the room. The commercial CFD software package futurefacilities6sigmadcx is used to develop the model for three configurations: (a) an aisle populated with ten (i.e., all) passive tiles; (b) a single active tile and nine passive tiles in the cold aisle; and (c) an aisle populated with all active tiles. The predictions from the CFD model are found to be in good agreement with the experimental data, with an average discrepancy between the measured and computed values for total flow rate and rack inlet temperature less than 4% and 1.7 °C, respectively. The validated models were then used to simulate steady-state and transient scenarios following cooling failure. This physics-based and experimentally validated room-level model can be used for temperature and flow distributions prediction and identifying optimal number and locations of active tiles for hot spot mitigation in data centers.

Sign in / Sign up

Export Citation Format

Share Document