The breast lesion excision system (BLES) under stereotactic guidance cannot be used as a therapeutic tool in the excision of small areas of microcalcifications in the breast

2017 ◽  
Vol 93 ◽  
pp. 252-257 ◽  
Author(s):  
Ruxandra-Iulia Milos ◽  
Maria Bernathova ◽  
Pascal A. Baltzer ◽  
Katja Pinker-Domenig ◽  
Panagiotis Kapetas ◽  
...  
Keyword(s):  
Breast Lesion ◽  
Therapeutic Tool ◽  
Small Areas ◽  
Stereotactic Guidance

Electron Diffraction of Wet Biological Membranes

1974 ◽  
Vol 32 ◽  
pp. 158-159
Author(s):  
S.W. Hui ◽  
D.F. Parsons
Keyword(s):  
Electron Diffraction ◽  
Data Collection ◽  
Biological Membranes ◽  
Small Areas ◽  
Electron Diffraction Technique ◽  
Electron Microscopes ◽  
Collection Time ◽  
Camera Length

The development of the hydration stages for electron microscopes has opened up the application of electron diffraction in the study of biological membranes. Membrane specimen can now be observed without the artifacts introduced during drying, fixation and staining. The advantages of the electron diffraction technique, such as the abilities to observe small areas and thin specimens, to image and to screen impurities, to vary the camera length, and to reduce data collection time are fully utilized. Here we report our pioneering work in this area.

Ultrastructure and Morphology of the Neurospora Crassa Cell Wall Mutants, Slime And Slime X, Using Tem and Sem

1976 ◽  
Vol 34 ◽  
pp. 54-55
Author(s):  
Karen S. Howard ◽  
H. D. Braymer ◽  
M. D. Socolofsky ◽  
S. A. Milligan
Keyword(s):  
Cell Wall ◽  
Neurospora Crassa ◽  
Wild Type ◽  
Morphological Comparison ◽  
Small Areas ◽  
Solid Media ◽  
Thin Sectioning ◽  
X Cells ◽  
Mutant Cells ◽  
Isolated Cell

The recently isolated cell wall mutant slime X of Neurospora crassa was prepared for ultrastructural and morphological comparison with the cell wall mutant slime. The purpose of this article is to discuss the methods of preparation for TEM and SEM observations, as well as to make a preliminary comparison of the two mutants.TEM: Cells of the slime mutant were prepared for thin sectioning by the method of Bigger, et al. Slime X cells were prepared in the same manner with the following two exceptions: the cells were embedded in 3% agar prior to fixation and the buffered solutions contained 5% sucrose throughout the procedure.SEM: Two methods were used to prepare mutant and wild type Neurospora for the SEM. First, single colonies of mutant cells and small areas of wild type hyphae were cut from solid media and fixed with OSO4 vapors similar to the procedure used by Harris, et al. with one alteration. The cell-containing agar blocks were dehydrated by immersion in 2,2-dimethoxypropane (DMP).

Selective Sampling and Orientation of Non-Homogeneous Tissues

1968 ◽  
Vol 26 ◽  
pp. 98-99
Author(s):  
C. C. Clawson ◽  
L. W. Anderson ◽  
R. A. Good
Keyword(s):  
Electron Microscopy ◽  
Electron Microscope ◽  
Light Microscopy ◽  
Random Sampling ◽  
New Method ◽  
Microscope Examination ◽  
Small Areas ◽  
Selective Sampling ◽  
Large Numbers ◽  
Specific Orientation

Investigations which require electron microscope examination of a few specific areas of non-homogeneous tissues make random sampling of small blocks an inefficient and unrewarding procedure. Therefore, several investigators have devised methods which allow obtaining sample blocks for electron microscopy from region of tissue previously identified by light microscopy of present here techniques which make possible: 1) sampling tissue for electron microscopy from selected areas previously identified by light microscopy of relatively large pieces of tissue; 2) dehydration and embedding large numbers of individually identified blocks while keeping each one separate; 3) a new method of maintaining specific orientation of blocks during embedding; 4) special light microscopic staining or fluorescent procedures and electron microscopy on immediately adjacent small areas of tissue.

The crystallization of thin-film ceramics

1992 ◽  
Vol 50 (1) ◽  
pp. 338-339
Author(s):  
J.M. Schwartz ◽  
L.F. Francis ◽  
L.D. Schmidt ◽  
P.S. Schabes-Retchkiman
Keyword(s):  
Thin Films ◽  
Grain Size ◽  
Sol Gel ◽  
Processing Route ◽  
Small Areas ◽  
Ceramic Thin Films ◽  
Complex Shapes ◽  
Sol Gel Process ◽  
Ceramic Precursors ◽  
Crystalline Ceramic

Ceramic thin films and coatings are of interest for electrical, optical, magnetic and thermal barrier applications. Critical for improved properties in thin films is the development of specific microstructures during processing. To this end, the sol-gel method is advantageous as a versatile processing route. The sol-gel process involves depositing a solution containing metalorganic or colloidal ceramic precursors onto a substrate and heating the deposited layer to form a crystalline or non-crystalline ceramic coating. This route has several advantages, including the ability to create tailored microstructures and properties, to coat large or small areas, simple or complex shapes, and to more easily prepare multicomponent ceramics. Sol-gel derived coatings are amorphous in the as-deposited state and develop their crystalline structure and microstructure during heat-treatment. We are particularly interested in studying the amorphous to crystalline transformation, because many key features of the microstructure such as grain size and grain size distribution may be linked to this transformation.

Données LiDAR aériennes: pertinence de l'interprétation visuelle pour la foresterie

2017 ◽  
Vol 168 (3) ◽  
pp. 127-133
Author(s):  
Matthew Parkan
Keyword(s):  
Cross Sections ◽  
Forest Edge ◽  
Airborne Lidar ◽  
Visual Interpretation ◽  
Individual Tree ◽  
Small Areas ◽  
Interactive 3D ◽  
The Individual ◽  
Airborne Lidar Data ◽  
Stem Position

Airborne LiDAR data: relevance of visual interpretation for forestry Airborne LiDAR surveys are particularly well adapted to map, study and manage large forest extents. Products derived from this technology are increasingly used by managers to establish a general diagnosis of the condition of forests. Less common is the use of these products to conduct detailed analyses on small areas; for example creating detailed reference maps like inventories or timber marking to support field operations. In this context, the use of direct visual interpretation is interesting, because it is much easier to implement than automatic algorithms and allows a quick and reliable identification of zonal (e.g. forest edge, deciduous/persistent ratio), structural (stratification) and point (e.g. tree/stem position and height) features. This article examines three important points which determine the relevance of visual interpretation: acquisition parameters, interactive representation and identification of forest characteristics. It is shown that the use of thematic color maps within interactive 3D point cloud and/or cross-sections makes it possible to establish (for all strata) detailed and accurate maps of a parcel at the individual tree scale.

Sign in / Sign up

Export Citation Format

Share Document