Experimental investigation on mechanical properties of fly ash-GGBFS based GO-geopolymer concrete using mineral sand (Quartz-Feldspar) as fine aggregate

2021 ◽  
Author(s):  
Sai Sunil S ◽  
Ramujee Kolli
Keyword(s):  
Mechanical Properties ◽  
Experimental Investigation ◽  
Fly Ash ◽  
Fine Aggregate ◽  
Geopolymer Concrete

scholarly journals Studies on manufactured sand effect on mechanical properties of geopolymer concrete as replacement of river sand in fine aggregate

2021 ◽  
Vol 309 ◽  
pp. 01114
Author(s):  
K. Veera Babu ◽  
T. Srinivas ◽  
Mahathi Tummala
Keyword(s):  
Mechanical Properties ◽  
Fly Ash ◽  
Construction Material ◽  
Environmental Concerns ◽  
Fine Aggregate ◽  
Geopolymer Concrete ◽  
River Sand ◽  
Natural Sand ◽  
Manufactured Sand ◽  
Low Calcium

Concrete is the most adaptable, long-lasting, and dependable construction material on the planet. There are numerous environmental concerns associated with the production of OPC, and natural sand is becoming more expensive and scarce as a result of unlawful river sand dredging. The greatest replacement material for traditional concrete is geopolymer concrete with low calcium fly ash. The purpose of this paper is to investigate the mechanical properties of geopolymer concrete of grades G30 and G50, which are equivalent to M30 and M50, when river sand is substituted in various quantities with manufactured sand, such as 0%, 10%, 20%, 30%, 40%, 50%, 60%, 70%, 80%, 90%, and 100%. When compared to the equivalent grades of controlled concrete, geopolymer concrete improves mechanical properties such as compressive, tensile, and flexural strengths.

scholarly journals An Experimental Study on Fibre Reinforced Geopolymer Concrete Composites- Glass Fibre, Copper Slag

2018 ◽  
Vol 7 (3.34) ◽  
pp. 433
Author(s):  
J Asanammal Saral ◽  
S Gayathri ◽  
M Tamilselvi ◽  
B Raghul Raj
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Fly Ash ◽  
Volume Fraction ◽  
Glass Fibers ◽  
Thermal Power ◽  
Copper Slag ◽  
Fine Aggregate ◽  
Geopolymer Concrete ◽  
Split Tensile Strength

The major problem of the world is facing today is environmental pollution. It is well known that for the production of 1-ton of cement consumes more energy and exhibit 0.8-ton of CO2 .On the other hand Fly ash is a residue from the combustion of pulverized coal from the flue gases of thermal power plant. Recently, the fly ash is not effectively used and a large part of it is disposed in landfill. Due to this problem the various researchers have sort for a new binder to minimize the consumption of OPC. This study evaluates the strength of geopolymer concrete having fly ash as the major binding material and the sand a fine aggregate was replaced with copper slag of 40%  and glass fiber to enhance the mechanical properties have been presented. This paper analyses on the mechanical properties of eopolymer concrete composites such as compressive strength, split tensile strength and water absorption in heat curing at 60˚C for 24 hrs in hot air oven. Glass fibers were added in the mix in the volume fraction of 0.5%, 1.0%, 1.5% and 2.0% volume of the concrete. The influence of fiber content in terms of volume fraction on the compressive, split tensile strength of geopolymer concrete is presented. The result shows the elevated performance of the properties exhibited by the geopolymeric concrete with and without fibres.

Experimental Investigation and Micro-Structural Evolution Analysis of CNT & Fly Ash Reinforced Aluminium Matrix Composites

2015 ◽  
Vol 830-831 ◽  
pp. 429-432 ◽  
Author(s):  
Udaya ◽  
Peter Fernandes
Keyword(s):  
Mechanical Properties ◽  
Experimental Investigation ◽  
Fly Ash ◽  
Ball Milling ◽  
Milling Time ◽  
Structural Evolution ◽  
Matrix Composites ◽  
Evolution Analysis ◽  
Ball Milling Time ◽  
Al Matrix

The paper illustrates Carbon nanotubes reinforced pure Al (CNT/Al) composites and fly ash reinforced pure Al (FA/Al) composites produced by ball-milling and sintering. Microstructures of the fabricated composite were examined and the mechanical properties of the composites were tested and analysed. It was indicated that the CNTs and fly ash were uniformly dispersed into the Al matrix as ball-milling time increased with increase in hardness.

scholarly journals Assessment of the Rheological and Mechanical Properties of Geopolymer Concrete Comprising Fly Ash and Fluid Catalytic Cracking Residue as Aluminosilicate Precursor

2021 ◽  
Vol 11 (7) ◽  
pp. 3032
Author(s):  
Tuan Anh Le ◽  
Sinh Hoang Le ◽  
Thuy Ninh Nguyen ◽  
Khoa Tan Nguyen
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
Elastic Modulus ◽  
Fly Ash ◽  
Flexural Strength ◽  
Catalytic Cracking ◽  
Fluid Catalytic Cracking ◽  
High Alumina ◽  
Geopolymer Concrete ◽  
Sem Images

The use of fluid catalytic cracking (FCC) by-products as aluminosilicate precursors in geopolymer binders has attracted significant interest from researchers in recent years owing to their high alumina and silica contents. Introduced in this study is the use of geopolymer concrete comprising FCC residue combined with fly ash as the requisite source of aluminosilicate. Fly ash was replaced with various FCC residue contents ranging from 0–100% by mass of binder. Results from standard testing methods showed that geopolymer concrete rheological properties such as yield stress and plastic viscosity as well as mechanical properties including compressive strength, flexural strength, and elastic modulus were affected significantly by the FCC residue content. With alkali liquid to geopolymer solid ratios (AL:GS) of 0.4 and 0.5, a reduction in compressive and flexural strength was observed in the case of geopolymer concrete with increasing FCC residue content. On the contrary, geopolymer concrete with increasing FCC residue content exhibited improved strength with an AL:GS ratio of 0.65. Relationships enabling estimation of geopolymer elastic modulus based on compressive strength were investigated. Scanning electron microscope (SEM) images and X-ray diffraction (XRD) patterns revealed that the final product from the geopolymerization process consisting of FCC residue was similar to fly ash-based geopolymer concrete. These observations highlight the potential of FCC residue as an aluminosilicate source for geopolymer products.

scholarly journals Effect of Elevated Temperature on Mechanical Properties of High-Volume Fly Ash-Based Geopolymer Concrete, Mortar and Paste Cured at Room Temperature

Polymers ◽  
2021 ◽  
Vol 13 (9) ◽  
pp. 1473
Author(s):  
Jun Zhao ◽  
Kang Wang ◽  
Shuaibin Wang ◽  
Zike Wang ◽  
Zhaohui Yang ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Elevated Temperature ◽  
Fly Ash ◽  
Residual Strength ◽  
Elevated Temperatures ◽  
High Volume ◽  
Sem Analysis ◽  
Geopolymer Concrete ◽  
Ordinary Concrete ◽  
Exposure Temperature

This paper presents results from experimental work on mechanical properties of geopolymer concrete, mortar and paste prepared using fly ash and blended slag. Compressive strength, splitting tensile strength and flexural strength tests were conducted on large sets of geopolymer and ordinary concrete, mortar and paste after exposure to elevated temperatures. From Thermogravimetric analyzer (TGA), X-ray diffraction (XRD), Scanning electron microscope (SEM) test results, the geopolymer exhibits excellent resistance to elevated temperature. Compressive strengths of C30, C40 and C50 geopolymer concrete, mortar and paste show incremental improvement then followed by a gradual reduction, and finally reach a relatively consistent value with an increase in exposure temperature. The higher slag content in the geopolymer reduces residual strength and the lower exposure temperature corresponding to peak residual strength. Resistance to elevated temperature of C40 geopolymer concrete, mortar and paste is better than that of ordinary concrete, mortar and paste at the same grade. XRD, TGA and SEM analysis suggests that the heat resistance of C–S–H produced using slag is lower than that of sulphoaluminate gel (quartz and mullite, etc.) produced using fly ash. This facilitates degradation of C30, C40 and C50 geopolymer after exposure to elevated temperatures.

Microstructure and Mechanical Properties of Ambiently-Cured Blended Coal Ash-Based Geopolymer Concrete

2016 ◽  
Vol 857 ◽  
pp. 400-404
Author(s):  
Tian Yu Xie ◽  
Togay Ozbakkaloglu
Keyword(s):  
Mechanical Properties ◽  
Experimental Study ◽  
Compressive Strength ◽  
Fly Ash ◽  
Bottom Ash ◽  
Coal Ash ◽  
Geopolymer Concrete ◽  
Mass Ratio ◽  
Blended Coal ◽  
Microstructure And Mechanical Properties

This paper presents the results of an experimental study on the behavior of fly ash-, bottom ash-, and blended fly and bottom ash-based geopolymer concrete (GPC) cured at ambient temperature. Four bathes of GPC were manufactured to investigate the influence of the fly ash-to-bottom ash mass ratio on the microstructure, compressive strength and elastic modulus of GPC. All the results indicate that the mass ratio of fly ash-to-bottom ash significantly affects the microstructure and mechanical properties of GPCs

Alternative Concrete – Geopolymer Concrete

2021 ◽  
Keyword(s):  
Mechanical Properties ◽  
Fly Ash ◽  
Construction Industry ◽  
Building Material ◽  
Construction Materials ◽  
Raw Material ◽  
Geopolymer Concrete ◽  
Sustainable Solutions ◽  
New Construction ◽  
Alkali Activated

Concrete is the most versatile, durable and reliable material and is the most used building material. It requires large amounts of Portland cement which has environmental problems associated with its production. Hence, an alternative concrete – geopolymer concrete is needed. The general aim of this book is to make significant contributions in understanding and deciphering the mechanisms of the realization of the alkali-activated fly ash-based geopolymer concrete and, at the same time, to present the main characteristics of the materials, components, as well as the influence that they have on the performance of the mechanical properties of the concrete. The book deals with in-depth research of the potential recovery of fly ash and using it as a raw material for the development of new construction materials, offering sustainable solutions to the construction industry.

Sign in / Sign up

Export Citation Format

Share Document