scholarly journals An Experimental Study on Fibre Reinforced Geopolymer Concrete Composites- Glass Fibre, Copper Slag

2018 ◽  
Vol 7 (3.34) ◽  
pp. 433
Author(s):  
J Asanammal Saral ◽  
S Gayathri ◽  
M Tamilselvi ◽  
B Raghul Raj
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Fly Ash ◽  
Volume Fraction ◽  
Glass Fibers ◽  
Thermal Power ◽  
Copper Slag ◽  
Fine Aggregate ◽  
Geopolymer Concrete ◽  
Split Tensile Strength

The major problem of the world is facing today is environmental pollution. It is well known that for the production of 1-ton of cement consumes more energy and exhibit 0.8-ton of CO2 .On the other hand Fly ash is a residue from the combustion of pulverized coal from the flue gases of thermal power plant. Recently, the fly ash is not effectively used and a large part of it is disposed in landfill. Due to this problem the various researchers have sort for a new binder to minimize the consumption of OPC. This study evaluates the strength of geopolymer concrete having fly ash as the major binding material and the sand a fine aggregate was replaced with copper slag of 40%  and glass fiber to enhance the mechanical properties have been presented. This paper analyses on the mechanical properties of eopolymer concrete composites such as compressive strength, split tensile strength and water absorption in heat curing at 60˚C for 24 hrs in hot air oven. Glass fibers were added in the mix in the volume fraction of 0.5%, 1.0%, 1.5% and 2.0% volume of the concrete. The influence of fiber content in terms of volume fraction on the compressive, split tensile strength of geopolymer concrete is presented. The result shows the elevated performance of the properties exhibited by the geopolymeric concrete with and without fibres.

Effect of Alkaline Activator Ratio to Mechanical Properties of Geopolymer Concrete with Trass as Filler

2015 ◽  
Vol 754-755 ◽  
pp. 406-412 ◽  
Author(s):  
Puput Risdanareni ◽  
Januarti Jaya Ekaputri ◽  
Mohd Mustafa Al Bakri Abdullah
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Fly Ash ◽  
Sodium Silicate ◽  
Setting Time ◽  
Geopolymer Concrete ◽  
Closed Porosity ◽  
Split Tensile Strength ◽  
Alkaline Activator ◽  
Test Result

This paper describes the effect of alkaline activator ratio (Na2SiO3/NaOH) to mechanical properties of geopolymer concrete. The mechanical properties of geopolymer concrete were assessed by setting time, split tensile strength and porosity. Fly ash was used as a cement substitute, and trass used as filler. While, Natrium hydroxide (NaOH) and Sodium Silicate (Na2SiO3) was applied as alkaline activator. In this study, NaOH concentration eight and ten molar with an alkaline activator ratio Na2SiO3/ NaOH by mass: 0.5, 1, 1.5, 2 and 2.5 were used. The test result showed that setting time, porosity and split tensile strength of geopolymer concrete were hardly influenced by NaOH concentration and the alkaline activator ratio. The alkaline activator ratio of Na2SiO3/NaOH has an optimum value at 2 and 2.5. Test result showed that the fastest setting time was 25 minute, the highest amount of closed porosity was 9.035 % and the highest split tensile strength was 2.86 MPa.

scholarly journals A Comprehensive Study on Mechanical Properties of Nominal Grade Concrete Using Copper Slag as Partial Replacement to Fine Aggregate

2018 ◽  
Vol 7 (2.23) ◽  
pp. 443
Author(s):  
USHAKRANTI J ◽  
SRINIVASU K ◽  
NAGA SAI
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Compressive Strength ◽  
Experimental Studies ◽  
Copper Slag ◽  
Copper Production ◽  
Partial Replacement ◽  
Fine Aggregate ◽  
Split Tensile Strength ◽  
The Impact

Currently situation, improvement of infrastructure has created an excessive demand for herbal sand, which makes it greater expensive and leads to environmental imbalances. The utilization of suitable sustainable choice materials proves that it is the most efficacious choice to traditional concrete materials and can take care of the surrounding environment. Copper slag is an industrial byproduct of copper production. Copper slag is a high-gravity glassy granular material. This paper reports some experimental studies on the outcome of partially changed sand from impact of copper slag on the mechanical houses of concrete. M30 concrete adopts copper slag plan and partly substitutes high-quality combination fines by means of 0%, 10%, 20%, 30%, 40%, 50%, 60%, 80% and 100%. The mechanical properties of concrete measured in the laboratory encompass compressive strength, split tensile strength and bending tensile strength. The have an impact on of partly replacing the quality aggregates with copper slag on the compressive strength, the cut up tensile power of the cylinder and the bending power of the prism has been evaluated. Water absorption assessments have been also conducted to report the impact of copper slag on the absorption price of concrete. Test results affords that it is feasible to utilize copper slag as best aggregate in concrete. 

scholarly journals Combined Effect of Fly-Ash and Ferrochrome Ash as Partial Replacement of Cement on Mechanical Properties of Concrete

2019 ◽  
Vol 93 ◽  
pp. 02008
Author(s):  
Tribikram Mohanty ◽  
Sauna Majhi ◽  
Purnachandra Saha ◽  
Bitanjaya Das
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Compressive Strength ◽  
Fly Ash ◽  
Power Plants ◽  
Thermal Power ◽  
Mineral Admixture ◽  
Waste Materials ◽  
Partial Replacement ◽  
Split Tensile Strength

Due to rapid industrialization extensive quantity of waste materials like fly ash, silica fume, rice ash husk, and ferrochrome ash etc. are generated. Ferrochrome ash is generated from Ferro-alloy industry and fly-ash is produced in thermal power plants are alternative materials which have the potential of being utilized in concrete as a mineral admixture. The present investigation considers the combined influence on strength of concrete using various percentage fly ash and ferrochrome ash as partial replacement of cement. Experiments are carried out to get mechanical properties of ordinary Portland cement by replacement of fly ash by 10%, 20%, 30 % and 3% by ferrochrome ash. Mechanical properties are measured by determining compressive strength, split tensile strength and flexural strength. It can be inferred from the study that a small amount of ferrochrome ash mixed with 30 % fly-ash gives higher compressive strength as compared to fly ash alone. Addition of ferrochrome ash also increases the split tensile strength of concrete. Since ferrochrome ash and fly-ash are both industrial waste, utilization of these waste materials reduced the burden of dumping and greenhouse gas and thereby produce sustainable concrete.

scholarly journals Mechanical and Material Properties of Mortar Reinforced with Glass Fiber: An Experimental Study

Materials ◽  
2021 ◽  
Vol 14 (3) ◽  
pp. 698 ◽  
Author(s):  
Marcin Małek ◽  
Mateusz Jackowski ◽  
Waldemar Łasica ◽  
Marta Kadela ◽  
Marcin Wachowski
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Glass Fibers ◽  
Progressive Increase ◽  
Split Tensile Strength ◽  
Glass Waste ◽  
Poisson Coefficient ◽  
Recycled Glass ◽  
Setting Times ◽  
The World

The progressive increase in the amount of glass waste produced each year in the world made it necessary to start the search for new recycling methods. This work summarizes the experimental results of the study on mortar samples containing dispersed reinforcement in the form of glass fibers, fully made from melted glass waste (bottles). Mortar mixes were prepared according to a new, laboratory-calculated recipe containing glass fibers, granite as aggregate, polycarboxylate-based deflocculant and Portland cement (52.5 MPa). This experimental work involved three different contents (600, 1200, and 1800 g/m3) of recycled glass fibers. After 28 days, the mechanical properties such as compressive, flexural, and split tensile strength were characterized. Furthermore, the modulus of elasticity and Poisson coefficient were determined. The initial and final setting times, porosity, and pH of the blends were measured. Images of optical microscopy (OM) were taken. The addition of glass fibers improves the properties of mortar. The highest values of mechanical properties were obtained for concrete with the addition of 1800 g/m3 of glass fibers (31.5% increase in compressive strength, 29.9% increase in flexural strength, and 97.6% increase in split tensile strength compared to base sample).

Physical Properties of Volcanic Ash Based Geopolymer Concrete

2016 ◽  
Vol 841 ◽  
pp. 1-6 ◽  
Author(s):  
Puput Risdanareni ◽  
Adjib Karjanto ◽  
Febriano Khakim
Keyword(s):  
Tensile Strength ◽  
Fly Ash ◽  
Physical Properties ◽  
Volcanic Ash ◽  
Setting Time ◽  
Physical And Mechanical Properties ◽  
Ash Content ◽  
Geopolymer Concrete ◽  
Split Tensile Strength ◽  
Time Test

This paper describes the result of investigating volcanic ash of Mount Kelud as fly ash substitute material to produce geopolymer concrete. The test was held on geopolymer concrete blended with 0%, 25%, 50% and 100% fly ash replacement with volcanic ash. Natrium Hidroxide (NaOH) with concentration of 12 molar and Natrium Silicate (Na2SiO3) were used as alkaline activator. While alkali-activator ratio of 2 was used in this research. The physical properties was tested by porosity and setting time test, while split tensile strength presented to measure brittle caracteristic of geopolymer concrete. The result shown that increasing volcanic ash content in the mixture will increase setting time of geopolymer paste. On the other hand increasing volcanic ash content will reduce split tensile strength and porosity of geopolymer concrete. After all replacing fly ash with volcanic ash was suitable from 25% to 50% due to its optimum physical and mechanical properties.

scholarly journals Determination of Mechanical Properties of Rubberized Concrete in Marine Environment

2019 ◽  
Vol 8 (2) ◽  
pp. 5761-5765
Keyword(s):  
Mechanical Properties ◽  
Fly Ash ◽  
Marine Environment ◽  
Concrete Specimen ◽  
Crumb Rubber ◽  
Fine Aggregate ◽  
Test Results ◽  
Rubberized Concrete ◽  
Split Tensile Strength

With an objective of saving the environment by providing crumb rubber as an alternative to natural fine aggregate this paper presents a study carried out to find the mechanical properties of rubberized concrete. Rubberized concrete is made up of waste rubber from vehicle tyres and other rubber waste which otherwise is left out polluting the environment. In this paper, 7.5% of crumb rubber (obtained by shredding the vehicle tyres) as an alternative to fine aggregate and 7.5% of fly-ash as an alternative to cement is added with other ingredients of concrete to produce an eco-friendly concrete which can be used economically and effectively for construction along the coastal areas. Various properties like workability, compressive strength, split tensile strength, and flexural strength was carried out on concrete specimens exposed to the natural marine environment along the coast of Visakhapatnam, Andhra Pradesh. The total exposure of concrete specimen was about 150 days, and various specimens were tested at 7, 28, 90, 120 and 150 days, respectively. The test results showed that with a slight compromise in strength, the workability of concrete and resistance to the effect of seawater on the strength of concrete significantly improved with the addition of crumb rubber and fly-ash.

scholarly journals Effect of Carboxylic Acid (Benzene Crystallable) in Cement Concrete and Geopolymer Concrete

2020 ◽  
Vol 9 (7) ◽  
pp. 472-475
Keyword(s):  
Tensile Strength ◽  
Compressive Strength ◽  
Fly Ash ◽  
Carboxylic Acid ◽  
Geopolymer Concrete ◽  
Cement Concrete ◽  
Split Tensile Strength ◽  
Sealing Capacity ◽  
Time Period

The present study appraises the recitals of carboxylic acid- based admixture to increase concrete water tightness and self-sealing capacity of the cement and geopolymer concrete. Outcomes of the previous studies in particular, adding 1% by cement mass of the carboxylic polymer reasons for reduction in the water dispersion under pressure of 7-day wet cured concrete by 50% associated to that of the conforming reference concrete. At 7 days, M4 mix compressive strength is about 43.5% less than M3 mix. The compressive strength of M4 increases and is about 37.6% less than M3 mix at 28 days of curing. At 7 days, M4 mix split tensile strength is about 17.5% less than M3 mix (cement concrete with 0.45 w/c ratio). The split tensile strength of M4 declines and is about 42.3% less than M3 mix at 28 days of curing. The strength of the geopolymer concrete tends to increase as the time period increases due to the presence of fly ash in it. So it is expected that geopolymer concrete will give more strength than cement concrete in long term with the presence of carboxylic acid

scholarly journals Use of waste paper ash or wood ash as substitution to fly ash in production of geopolymer concrete

2021 ◽  
Vol 30 (3) ◽  
pp. 464-476
Author(s):  
Haider Owaid ◽  
Haider Al-Baghdadi ◽  
Muna Al-Rubaye
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Compressive Strength ◽  
Fly Ash ◽  
Flexural Strength ◽  
Sodium Hydroxide ◽  
Wood Ash ◽  
Splitting Tensile Strength ◽  
Waste Paper ◽  
Geopolymer Concrete

Large quantities of paper and wood waste are generated every day, the disposal of these waste products is a problem because it requires huge space for their disposal. The possibility of using these wastes can mitigate the environmental problems related to them. This study presents an investigation on the feasibility of inclusion of waste paper ash (WPA) or wood ash (WA) as replacement materials for fly ash (FA) class F in preparation geopolymer concrete (GC). The developed geopolymer concretes for this study were prepared at replacement ratios of FA by WPA or WA of 25, 50, 75 and 100% in addition to a control mix containing 100% of FA. Sodium hydroxide (NaOH) solutions and sodium silicate (Na2SiO3) are used as alkaline activators with 1M and 10M of sodium hydroxide solution.The geopolymer concretes have been evaluated with respect to the workability, the compressive strength, splitting tensile strength and flexural strength. The results indicated that there were no significant differences in the workability of the control GC mix and the developed GC mixes incorporating WPA or WA. Also, the results showed that, by incorporating of 25–50% PWA or 25% WA, the mechanical properties (compressive strength, splitting tensile strength and flexural strength) of GC mixes slightly decreased. While replacement with 75–100% WPA or with 50–100% WA has reduced these mechanical properties of GC mixes. As a result, there is a feasibility of partial replacement of FA by up to 50% WPA or 25% WA in preparation of the geopolymer concrete.

scholarly journals Characteristics of Blended Geopolymer Concrete Using Ultrafine Ground Granulated Blast Furnace Slag and Copper Slag

2020 ◽  
Vol 44 (6) ◽  
pp. 433-439
Author(s):  
Vijayasarathy Rathanasalam ◽  
Jayabalan Perumalsami ◽  
Karthikeyan Jayakumar
Keyword(s):  
Blast Furnace ◽  
Fly Ash ◽  
Sodium Hydroxide ◽  
Blast Furnace Slag ◽  
Copper Slag ◽  
Fine Aggregate ◽  
Geopolymer Concrete ◽  
Strength Performance ◽  
Granulated Blast Furnace Slag ◽  
Furnace Slag

This paper presents the properties of blended geopolymer concrete manufactured using fly ash and ultrafine Ground Granulated Blast Furnace Slag (UFGGBFS), along with the copper slag (CPS) as replacement of fine aggregate (crushed stone sand). Various parameters considered in this study include different sodium hydroxide concentrations (10M, 12M and 14M); 0.35 as alkaline liquid to binder ratio; 2.5 as sodium silicate to sodium hydroxide ratio and cured in ambient curing condition. Further, geopolymer concrete was manufactured using fly ash as the prime source material which is replaced with UFGGBFS (0%, 5%, 10% and 15%). Copper slag has been used as replacement of fine aggregate in this study. Properties of the fresh manufactured geopolymer concrete were studied by slump test. Compressive strength of the manufactured geopolymer concrete was tested and recorded after curing for 3, 7 and 28 days. Microstructure Characterization of Geopolymer concrete specimens was done by Scanning Electron Microscope (SEM) analysis. Experimental results revealed that the addition of UFGGBFS resulted in an increased strength performance of geopolymer concrete. Also, this study demonstrated that the strength of geopolymer concrete increased with an increase in sodium hydroxide concentration. SEM results revealed that the addition of UFGGBFS resulted in a dense structure.

scholarly journals Effect of Design Parameters on Compressive and Split Tensile Strength of Self-Compacting Concrete with Recycled Aggregate: An Overview

2021 ◽  
Vol 11 (13) ◽  
pp. 6028
Author(s):  
P. Jagadesh ◽  
Andrés Juan-Valdés ◽  
M. Ignacio Guerra-Romero ◽  
Julia M. Morán-del Morán-del Pozo ◽  
Julia García-González ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Recycled Aggregate ◽  
Recycled Aggregates ◽  
Design Parameters ◽  
Fine Aggregate ◽  
Self Compacting Concrete ◽  
Split Tensile Strength ◽  
Coarse Aggregates ◽  
Fine Aggregates

One of the prime objectives of this review is to understand the role of design parameters on the mechanical properties (Compressive and split tensile strength) of Self-Compacting Concrete (SCC) with recycled aggregates (Recycled Coarse Aggregates (RCA) and Recycled Fine Aggregates (RFA)). The design parameters considered for review are Water to Cement (W/C) ratio, Water to Binder (W/B) ratio, Total Aggregates to Cement (TA/C) ratio, Fine Aggregate to Coarse Aggregate (FA/CA) ratio, Water to Solid (W/S) ratio in percentage, superplasticizer (SP) content (kg/cu.m), replacement percentage of RCA, and replacement percentage of RFA. It is observed that with respect to different grades of SCC, designed parameters affect the mechanical properties of SCC with recycled aggregates.

Sign in / Sign up

Export Citation Format

Share Document