Effects of lattice parameter changes on critical resolved shear stress and mechanical properties of magnesium binary single crystals

2012 ◽  
Vol 540 ◽  
pp. 198-206 ◽  
Author(s):  
Hyung Lae Kim ◽  
Jae Sin Park ◽  
Young Won Chang
Keyword(s):  
Mechanical Properties ◽  
Shear Stress ◽  
Single Crystals ◽  
Lattice Parameter ◽  
Critical Resolved Shear Stress

Effects of Mo Addition on Deformation Behavior of Metastable Beta-Type Ti-Mn Single Crystals

2018 ◽  
Vol 941 ◽  
pp. 1360-1365 ◽  
Author(s):  
Ryota Morioka ◽  
Ken Cho ◽  
Hiroyuki Y. Yasuda
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Shear Stress ◽  
Ultimate Tensile Strength ◽  
Single Crystals ◽  
Deformation Behavior ◽  
Deformation Structures ◽  
Critical Resolved Shear Stress ◽  
Metastable Beta ◽  
First Time

In this study, to clarify the effects of Mo addition on deformation behavior of Ti-Mn alloys, the mechanical properties and the deformation structures of the alloys were investigated using Ti-Mn and Ti-Mn-Mo alloys polycrystals and single crystals. We found that the elongation of Ti-Mn alloys are improved from approximately 5% to 30% by Mo addition, with maintaining ultimate tensile strength of 900 MPa. The excellent strength-ductility balance of Ti-Mn-Mo alloys is caused by {332}<113> twinning, which is unique twinning for metastable β-type titanium alloys. Additionally, the deformation behavior of Ti-Mn and Ti-Mn-Mo alloys was investigated in detail by using single crystals focusing on a critical resolved shear stress (CRSS). As a result, we found for the first time that CRSS for {332}<113> twinning in Ti-Mn-Mo alloy was lower than that in Ti-Mn alloy. Moreover, in Ti-Mn-Mo alloy, CRSS for {332}<113> twinning was lower than that for {112}<111> slip. These results suggest that CRSS for {332}<113> twinning in Ti-Mn alloys is decreased by Mo addition.

THE EFFECT OF ORIENTATION AND IMPURITIES ON THE MECHANICAL PROPERTIES OF MOLYBDENUM SINGLE CRYSTALS

1967 ◽  
Vol 45 (2) ◽  
pp. 1063-1074 ◽  
Author(s):  
D. F. Stein
Keyword(s):  
Mechanical Properties ◽  
Shear Stress ◽  
Single Crystals ◽  
Tensile Axis ◽  
Zone Melting ◽  
Hydrogen Gas ◽  
Axis Orientation ◽  
Stereographic Triangle ◽  
Tension And Compression ◽  
Critical Resolved Shear Stress

Molybdenum single crystals containing less than 10 p.p.m. of carbon, 5 p.p.m. of nitrogen, and 5 p.p.m. of oxygen have been prepared by zone melting and hydrogen gas purification. The mechanical properties of the crystals have been measured in tension and compression over a range of temperature from 20 to 298 °K. It was found that the critical resolved shear stress and the temperature dependence of the critical resolved shear stress decreased with increasing purity. It was found that at all test temperatures the CRSS law fails. The critical resolved shear stress is a minimum in the (100) tension axis orientation and reaches a maximum with the tensile axis along the (110)(111) line of the stereographic triangle. It was also found that the ductility of molybdenum single crystals was not improved by purification.

scholarly journals Enhanced lattice distortion, yield strength, critical resolved shear stress, and improving mechanical properties of transition-metals doped CrCoNi medium entropy alloy

RSC Advances ◽  
2021 ◽  
Vol 11 (38) ◽  
pp. 23719-23724
Author(s):  
Md. Lokman Ali
Keyword(s):  
Mechanical Properties ◽  
Shear Stress ◽  
Transition Metals ◽  
Yield Strength ◽  
Lattice Distortion ◽  
Critical Resolved Shear Stress

The effect of transition-metals (TM) addition on the mechanical properties of CrCoNi medium entropy alloys (MEAs) was investigated.

The Effect of Solid Solution Impurities on Dislocation Nucleation in a (001) Mo – 1.5 at.% Ir Single Crystal

2010 ◽  
Vol 662 ◽  
pp. 85-93
Author(s):  
Sergey Dub ◽  
Igor Zasimchuk ◽  
Leonid Matvienko
Keyword(s):  
Mechanical Properties ◽  
Solid Solution ◽  
Shear Stress ◽  
Elastic Modulus ◽  
Single Crystal ◽  
Single Crystals ◽  
Free Volume ◽  
Dislocation Nucleation ◽  
Initial Portion ◽  
G 12

Mechanical properties of (001) Mo and (001) Mo – 1.5 at.% Ir single crystals have been studied by nanoindentation. It has been found that the iridium addition to molybdenum leads to an increase in both hardness and elastic modulus. An abrupt elasto-plastic transition (pop-in) at a depth of about 20 - 40 nm caused by dislocation nucleation in previously dislocation-free volume has been observed in the initial portion of the loading curve. It has shown that the Ir addition essentially affects the dislocation nucleation. Mean shear stress required for the dislocation nucleation increased from 10.8 GPa (G/12) for a Mo single crystal to 18.2 GPa (G/8) for the Mo – 1.5 at% Ir solid solution. Thus, the Ir solution in a Mo single crystal affects not only the resistance to the motion of dislocations (hardness) but the nucleation of them as well. The latter is likely to occur as a result of an increase in the structure perfection of the Mo – 1.5 at% Ir solid solution as compared to the pure Mo single crystal.

Plastic Deformations in L10-Ordered Single Crystals with their c/a Ratios Less than Unity

2007 ◽  
Vol 561-565 ◽  
pp. 459-462
Author(s):  
Katsushi Tanaka ◽  
Hiromitsu Ide ◽  
Yoshinori Sumi ◽  
Kyosuke Kishida ◽  
Haruyuki Inui
Keyword(s):  
Shear Stress ◽  
Temperature Dependence ◽  
Single Crystals ◽  
Room Temperature ◽  
The Other ◽  
Compressive Deformation ◽  
Positive Temperature ◽  
Plastic Deformations ◽  
Temperature Range ◽  
Critical Resolved Shear Stress

Compressive deformation of L10-ordered single crystals of FePd whose c/a ratio less than unity have been investigated from room temperature to 823 K. The results show that the critical resolved shear stress (CRSS) for octahedral glide of ordinary dislocations is smaller than that of super-lattice dislocations in all the temperature range investigated, that is the opposite sense to the case of Ti-56 mol% Al. The CRSS for ordinary dislocations virtually independent to the temperature. On the other hand, the CRSS for super dislocations exhibits a weak positive temperature dependence from room temperature up to 573 K and decreases in higher temperatures.

Room Temperature Deformation in “Soft” Orientation Nial Single Crystals

1990 ◽  
Vol 213 ◽  
Author(s):  
R.D. Field ◽  
D.F. Lahrman ◽  
R. Darolia
Keyword(s):  
Shear Stress ◽  
Elevated Temperature ◽  
Single Crystals ◽  
Room Temperature ◽  
Dislocation Motion ◽  
Temperature Deformation ◽  
Slip Planes ◽  
Schmid Factor ◽  
Critical Resolved Shear Stress ◽  
Active Slip

ABSTRACTA detailed study of deformation of NiAl single crystals in two soft orientations, <110> and <111>, has been conducted. The Schmid factor favors {100} slip in the former and {110} slip in the latter. Detailed dislocation analysis, critical resolved shear stress measurements, and slip trace analysis have been performed to determine the nature of dislocation motion and interactions in this material. Particular attention is given to prismatic loops formed during deformation, since the shapes of these loops reveal the active slip planes. Similar loop morphologies observed in elevated temperature [001] oriented tensile specimens are also discussed.

Accommodation of constrained deformation in f. c. c. metals by slip and twinning

1969 ◽  
Vol 309 (1499) ◽  
pp. 433-456 ◽  
Keyword(s):  
Shear Stress ◽  
Single Crystals ◽  
Plane Strain ◽  
Plane Strain Compression ◽  
Orientation Factor ◽  
Cubic Crystals ◽  
Constrained Deformation ◽  
Critical Resolved Shear Stress ◽  
Good Agreement ◽  
External Strain

The problem of accommodation of constrained deformation by slip and twinning has been analysed. The analysis is based on Taylor’s least work hypothesis. In this analysis, the operative combination of slip and twinning systems is found by minimizing the orientation factor M = (∑ i s i +α∑ i t i )/ ε , where s i and t i are the simple shears resulting from slip and twinning respectively, α is the ratio of the critical resolved shear stress for twinning against slip, and Ɛ is the external strain. Detailed calculations have been made for face-centred cubic crystals deformed by plane strain compression. Experimental observations on deformed single crystals of a Co–8% Fe alloy indicate good agreement with the analysis. Implications of the present study to the twinning observations of Heye & Wassermann on rolled Ag crystals are discussed.

Sign in / Sign up

Export Citation Format

Share Document