Assessment of activity indexes on the splitting tensile strengthening of geopolymer concrete incorporating supplementary cementitious materials

2020 ◽  
Vol 24 ◽  
pp. 101356
Author(s):  
Solomon Oyebisi ◽  
Anthony Ede ◽  
Festus Olutoge ◽  
Ben Ngene
Keyword(s):  
Cementitious Materials ◽  
Supplementary Cementitious Materials ◽  
Geopolymer Concrete

Crack Growth Resistance in Fibre Reinforced Geopolymer Concrete Exposed to Sustained Extreme Temperatures

2016 ◽  
Vol 711 ◽  
pp. 511-518 ◽  
Author(s):  
Vivek Bindiganavile ◽  
Jose R.A. Goncalves ◽  
Yaman Boluk
Keyword(s):  
Portland Cement ◽  
Crack Growth ◽  
Volume Fraction ◽  
Cementitious Materials ◽  
Supplementary Cementitious Materials ◽  
Geopolymer Concrete ◽  
Extreme Temperatures ◽  
Portland Cement Concrete ◽  
Promising Alternative ◽  
Cement Binder

Portland cement concrete (PCC) is now second only to potable water in per capita consumption. And notwithstanding its numerous benefits, Portland cement itself is responsible for between 4 to 5% of the world’s manmade greenhouse gas emissions. In this context, geopolymer concrete is a promising alternative, wherein the Portland cement binder is replaced entirely by supplementary cementitious materials triggered by alkaline activators. Relatively little is known on the fracture response of this system, especially when exposed to extreme temperatures. The study reported here focused on the crack growth response of such a system prepared with Class F fly ash and reinforced with steel and polymeric fibres up to 1% volume fraction. The geopolymerization was effected with a blend of sodium hydroxide and sodium silicate to achieve a compressive strength of 30 MPa at 28 days. The resulting geopolymer concrete was subjected to temperatures between-30 oC to 300 oC, sustained for 2 hours. A fibre blend of steel to polypropylene in the mass ratio of 4:1 was incorporated. Based on the results, four different stages for fracture behaviour were identified with superior fibre efficiency seen at sub-zero temperatures.

Effect of ground granulated blast funrnace slag and fly ash on strength, permeability, and under-water abrasion of fine-grained concrete

2020 ◽  
Vol 71 (7) ◽  
pp. 775-788
Author(s):  
Quyet Truong Van ◽  
Sang Nguyen Thanh
Keyword(s):  
Fly Ash ◽  
Concrete Strength ◽  
Cementitious Materials ◽  
Supplementary Cementitious Materials ◽  
Chloride Permeability ◽  
Cement Replacement ◽  
Fine Grained ◽  
Granulated Blast Furnace Slag ◽  
Compressive Strength Test ◽  
Economic Ground

The utilisation of supplementary cementitious materials (SCMs) is widespread in the concrete industry because of the performance benefits and economic. Ground granulated blast furnace slag (GGBFS) and fly ash (FA) have been used as the SCMs in concrete for reducing the weight of cement and improving durability properties. In this study, GGBFS at different cement replacement ratios of 0%, 20%, 40% and 60% by weight were used in fine-grained concrete. The ternary binders containing GGBFS and FA at cement replacement ratio of 60% by weight have also evaluated. Flexural and compressive strength test, rapid chloride permeability test and under-water abrasion test were performed. Experimental results show that the increase in concrete strength with GGBFS contents from 20% to 40% but at a higher period of maturity (56 days and more). The chloride permeability the under-water abrasion reduced with the increasing cement replacement by GGBFS or a combination of GGBFS and FA

Evaluation of strength of concrete on different initial exposure condition

2020 ◽  
Vol 13 ◽  
Author(s):  
Sri Ram Krishna Mishra ◽  
Pradeep Kumar Ghosh ◽  
Manoj Kulshreshtha
Keyword(s):  
Portland Cement ◽  
High Strength ◽  
Cementitious Materials ◽  
General Purpose ◽  
Supplementary Cementitious Materials ◽  
Exposure Condition ◽  
Portland Cement Concrete ◽  
Initial Exposure ◽  
Skilled Manpower ◽  
Standard Practices

Background: The previous studies have focused curing effect of mainly on high strength concrete, where strict supervision is maintained. This study is based upon general purpose concreting work for commercial and residential construction in absence of skilled manpower and supervision. Objective: The objective of this study is to establish a thumb rule to provide 7 days initial curing for maintaining quality for unsupervised concreting irrelevant to type of cement and grading. Methods: In this study concrete samples made with locally available commercial cements were cured for various initial exposure. Results: The results shows that concrete cured after a gap of 4 days from the time of de-moulding have given lowest strength as compared to concrete cured in standard practices i.e. where proper curing protocol had been followed. Conclusion: Initial curing is most important aspect of gaining desired strength. The findings after this study shows that curing affects the strength of concrete in variable grading. Initial curing has great importance for concrete with all types of Portland cement. Concrete with supplementary cementitious materials gives lowest strength initially but results higher strength after 28 days as compared to Portland cement.

scholarly journals Supplementary cementitious materials origin from agricultural wastes – A review

2015 ◽  
Vol 74 ◽  
pp. 176-187 ◽  
Author(s):  
Evi Aprianti ◽  
Payam Shafigh ◽  
Syamsul Bahri ◽  
Javad Nodeh Farahani
Keyword(s):  
Cementitious Materials ◽  
Agricultural Wastes ◽  
Supplementary Cementitious Materials

scholarly journals Special Issue: Supplementary Cementitious Materials in Concrete, Part I

Materials ◽  
2021 ◽  
Vol 14 (9) ◽  
pp. 2291
Author(s):  
Alessandro P. Fantilli ◽  
Daria Jóźwiak-Niedźwiedzka
Keyword(s):  
Environmental Impact ◽  
Portland Cement ◽  
Building Materials ◽  
Cementitious Materials ◽  
Supplementary Cementitious Materials ◽  
Special Issue ◽  
Cement Production ◽  
Concrete Part

The environmental impact of the Portland cement production and the large use of cement-based building materials is a growing problem [...]

scholarly journals Use of Treated Non-Ferrous Metallurgical Slags as Supplementary Cementitious Materials in Cementitious Mixtures

2021 ◽  
Vol 11 (9) ◽  
pp. 4028
Author(s):  
Asghar Gholizadeh Vayghan ◽  
Liesbeth Horckmans ◽  
Ruben Snellings ◽  
Arne Peys ◽  
Priscilla Teck ◽  
...  
Keyword(s):  
Mechanical Performance ◽  
Cementitious Materials ◽  
Supplementary Cementitious Materials ◽  
Partial Replacement ◽  
Strength Development ◽  
Supplementary Cementitious Material ◽  
Performance Requirements ◽  
Metallurgical Slags ◽  
Leaching Behaviour ◽  
Kinetics Of

This research investigated the possibility of using metallurgical slags from the copper and lead industries as partial replacement for cement. The studied slags were fayalitic, having a mainly ferro-silicate composition with minor contents of Al2O3 and CaO. The slags were treated at 1200–1300 °C (to reduce the heavy metal content) and then granulated in water to promote the formation of reactive phases. A full hydration study was carried out to assess the kinetics of reactions, the phases formed during hydration, the reactivity of the slags and their strength activity as supplementary cementitious material (SCM). The batch-leaching behaviour of cementitious mixtures incorporating treated slags was also investigated. The results showed that all three slags have satisfactory leaching behaviour and similar performance in terms of reactivity and contribution to the strength development. All slags were found to have mediocre reactivity and contribution to strength, especially at early ages. Nonetheless, they passed the minimum mechanical performance requirements and were found to qualify for use in cement.

scholarly journals A Review of the Mechanical Properties and Durability of Ecological Concretes in a Cold Climate in Comparison to Standard Ordinary Portland Cement-Based Concrete

Materials ◽  
2020 ◽  
Vol 13 (16) ◽  
pp. 3467
Author(s):  
Ankit Kothari ◽  
Karin Habermehl-Cwirzen ◽  
Hans Hedlund ◽  
Andrzej Cwirzen
Keyword(s):  
Carbon Dioxide ◽  
Portland Cement ◽  
Ordinary Portland Cement ◽  
Cementitious Materials ◽  
Cold Climate ◽  
Supplementary Cementitious Materials ◽  
Short Exposure ◽  
Chemical Admixtures ◽  
Composite Cements ◽  
Alkali Activated

Most of the currently used concretes are based on ordinary Portland cement (OPC) which results in a high carbon dioxide footprint and thus has a negative environmental impact. Replacing OPCs, partially or fully by ecological binders, i.e., supplementary cementitious materials (SCMs) or alternative binders, aims to decrease the carbon dioxide footprint. Both solutions introduced a number of technological problems, including their performance, when exposed to low, subfreezing temperatures during casting operations and the hardening stage. This review indicates that the present knowledge enables the production of OPC-based concretes at temperatures as low as −10 °C, without the need of any additional measures such as, e.g., heating. Conversely, composite cements containing SCMs or alkali-activated binders (AACs) showed mixed performances, ranging from inferior to superior in comparison with OPC. Most concretes based on composite cements require pre/post heat curing or only a short exposure to sub-zero temperatures. At the same time, certain alkali-activated systems performed very well even at −20 °C without the need for additional curing. Chemical admixtures developed for OPC do not always perform well in other binder systems. This review showed that there is only a limited knowledge on how chemical admixtures work in ecological concretes at low temperatures and how to accelerate the hydration rate of composite cements containing high amounts of SCMs or AACs, when these are cured at subfreezing temperatures.

Sign in / Sign up

Export Citation Format

Share Document