A study on the synthesis of coarse TiO2 powder with controlled particle sizes and morphology via hydrolysis

2021 ◽  
Author(s):  
Ying Zhang ◽  
Zhigang Zak Fang ◽  
Pei Sun ◽  
Zhe Huang ◽  
Shili Zheng
Keyword(s):  
Particle Sizes ◽  
Tio2 Powder

Characterization of carbides in M50NiL

1991 ◽  
Vol 49 ◽  
pp. 606-607
Author(s):  
L. S. Lin ◽  
K. P. Gumz ◽  
A. V. Karg ◽  
C. C. Law
Keyword(s):  
Temperature Effects ◽  
Base Composition ◽  
Lattice Parameter ◽  
Control Surface ◽  
Carbide Formation ◽  
Particle Sizes ◽  
Low Carbon ◽  
Fee Structure ◽  
Heat Treated

Carbon and temperature effects on carbide formation in the carburized zone of M50NiL are of great importance because they can be used to control surface properties of bearings. A series of homogeneous alloys (with M50NiL as base composition) containing various levels of carbon in the range of 0.15% to 1.5% (in wt.%) and heat treated at temperatures between 650°C to 1100°C were selected for characterizations. Eleven samples were chosen for carbide characterization and chemical analysis and their identifications are listed in Table 1.Five different carbides consisting of M6C, M2C, M7C3 and M23C6 were found in all eleven samples examined as shown in Table 1. M6C carbides (with least carbon) were found to be the major carbide in low carbon alloys (<0.3% C) and their amounts decreased as the carbon content increased. In sample C (0.3% C), most particles (95%) encountered were M6C carbide with a particle sizes range between 0.05 to 0.25 um. The M6C carbide are enriched in both Mo and Fe and have a fee structure with lattice parameter a=1.105 nm (Figure 1).

TEM study on fine carbide precipitates and dislocation cell structure

1990 ◽  
Vol 48 (4) ◽  
pp. 904-905
Author(s):  
Mengzhe Chen ◽  
Siqin Wang ◽  
Jun Ke
Keyword(s):  
Carbide Particle ◽  
Cell Structure ◽  
Ferrite Matrix ◽  
Dislocation Cell ◽  
Isothermal Treatment ◽  
Particle Sizes ◽  
Dislocation Cell Structure ◽  
Thin Foils ◽  
Hsla Steels ◽  
Fine Carbide

A series of investigations have been conducted into the nature and origin of the dislocation cell structure. R.J.Klassen calculated that the dislocation cell limiting size in pure ferrite matrix is about 0.4 μm. M.N.Bassion estimated the size of dislocation cell in deformed ferrite of HSLA steels to be of the same order.In this paper, TEM observation has been concentrated on the interaction of fine carbide precipitates with dislocation cell structure in deformed Fe-C-V (0.05%C, 0.13% and 0.57%V) and Fe-C-Nb (0.07 %C and 0.04%Nb) alloys and compared with that in Fe-C (0.05%). Specimens were austenitized at 1500 “C/20 min and followed by isothermal treatment at 750 °C and 800 “C for 20, 40 and 120 minutes . The carbide particle sizes in these steels are from 9 to 86nm measured from carbon extraction replicas. Specimens for TEM were cut from differently deformed areas of tensile specimens deformed at room temperture. The thin foils were jet electropolished at -20 C in a solution of 10% perchloric acid and 90% ethanol. The TEM observation was carried out in JEM 100CX , EM420 at 100kv and JEM 2000FX at 200kv.

A High Resolution Study of Alumina Supported Iridium Catalysts

1980 ◽  
Vol 38 ◽  
pp. 202-203
Author(s):  
C. Stoeckert ◽  
B. Etherton ◽  
M. Beer ◽  
J. Gryder
Keyword(s):  
Electron Microscope ◽  
High Resolution ◽  
Metal Particles ◽  
Optical Transfer Function ◽  
Particle Sizes ◽  
Iridium Catalysts ◽  
Transmission Electron ◽  
Optical Transfer ◽  
Conventional Transmission Electron Microscope ◽  
Resolution Study

The interpretation of the activity of catalysts requires information about the sizes of the metal particles, since this has implications for the number of surface atoms available for reaction. To determine the particle dimensions we used a high resolution STEM1. Such an instrument with its simple optical transfer function is far more suitable than a conventional transmission electron microscope for the establishment of particle sizes. We report here our study on the size and number distribution of Ir particles supported on Al2O3 and also examine simple geometric models for the shape of Ir particles.

Separation of Plasminogen Activators from Human Uterine Tissue and a Comparison with Activators from Human Urine and Porcine Tissue

1979 ◽  
Vol 41 (04) ◽  
pp. 718-733 ◽  
Author(s):  
Preben Kok
Keyword(s):  
Plasminogen Activator ◽  
Human Urine ◽  
Gel Filtration ◽  
Ammonium Thiocyanate ◽  
Plasminogen Activators ◽  
Particle Sizes ◽  
Uterine Tissue ◽  
Porcine Tissue ◽  
Major Activity ◽  
Proliferative Phase

SummaryThree types of plasminogen activator could be distinguished in extracts from human uterine tissue. The activators differed in thermostability or in mode of inhibition by EACA.All the extracts contained stable as well as labile activators. The saline extracts were uniformly inhibited by increasing concentrations of EACA. Extracts made with 2 M ammonium thiocyanate were either uniformly inhibited by EACA or showed deflections indicating contamination with an activator, which was inhibited in a biphasic manner. It was possible to distinguish between: (1) An activator, abundantly present in the tissue, which was uniformly inhibited and stable. (2) Another uniformly inhibited activator, which was labile. (3) An activator, inhibited in a biphasic manner, similar to urokinase, which was present in varying amounts in uteri with the endometrium in the proliferative phase.Gel filtration of the uterine extracts showed two major activity peaks corresponding to particle sizes of 60,000 dalton and about 10,000 dalton.Antiserum to purified plasminogen activator, prepared from porcine ovaries, inhibited the activity of the human uterine extracts, but not the activities of human urokinase or urine. Urokinase antiserum in a concentration completely inhibiting human urine or urokinase, inhibited only 10% or less of the activities of human uterine extracts.

Flexographic ink-coating interactions: effects of latex variations in coating layers

TAPPI Journal ◽  
2016 ◽  
Vol 15 (4) ◽  
pp. 253-262 ◽  
Author(s):  
ERIK BOHLIN ◽  
CAISA JOHANNSON ◽  
MAGNUS LESTELIUS
Keyword(s):  
Contact Angles ◽  
High Ratio ◽  
Print Quality ◽  
Particle Sizes ◽  
Mixed Composition ◽  
Coating Surface ◽  
Covered Area ◽  
Surface Optical ◽  
Flexographic Printing ◽  
Coating Formulation

The effect of coating structure variations on flexographic print quality was studied using pilot-coated paperboard samples with different latex content and latex particle sizes. Two latexes, with particle sizes of 120 nm and 160 nm, were added at either 12 parts per hundred (pph) or 18 pph to the coating formulation. The samples were printed with full tone areas at print forces of 25 N and 50 N in a laboratory flexographic printing press using a waterbased ink. A high ratio of uncovered areas (UCAs) could be detected for the samples that contained 18 pph latex printed at a print force of 25 N. UCAs decreased with increased print force and with decreased amounts of latex in the coating formulation. The fraction of latex covered area on the coating surface was estimated to be 0.35–0.40 for the 12 pph, and 0.70–0.75 for the 18 pph samples. The ink penetration depth into the coating layer could be linked to the fraction of latex-free areas on the coating surface. Optical cross section microscopy indicated that a higher printing force did not increase the depth of penetrated ink to any greater extent. Higher printing force did increase contact between plate and substrate, leading to an improved distribution of the ink. This, in turn, increased print density and decreased UCAs. On closer inspection, the UCAs could be categorized as being induced by steep topographic changes. When appearing at other locations, they were more likely to be caused by poor wetting of the surface. To understand the wetting behavior of the coating surface, observed contact angles were compared with calculated contact angles on surfaces of mixed composition.

Surface energy of cellulosic materials: The effect of particle morphology, particle size, and hydroxyl number

TAPPI Journal ◽  
2015 ◽  
Vol 14 (9) ◽  
pp. 565-576 ◽  
Author(s):  
YUCHENG PENG ◽  
DOUGLAS J. GARDNER
Keyword(s):  
Particle Size ◽  
Surface Energy ◽  
Particle Morphology ◽  
Nanofibrillated Cellulose ◽  
Particle Sizes ◽  
Hydroxyl Number ◽  
Small Individual ◽  
Dispersion Component ◽  
Commercial Applications ◽  
Lower Temperature

Understanding the surface properties of cellulose materials is important for proper commercial applications. The effect of particle size, particle morphology, and hydroxyl number on the surface energy of three microcrystalline cellulose (MCC) preparations and one nanofibrillated cellulose (NFC) preparation were investigated using inverse gas chromatography at column temperatures ranging from 30ºC to 60ºC. The mean particle sizes for the three MCC samples and the NFC sample were 120.1, 62.3, 13.9, and 9.3 μm. The corresponding dispersion components of surface energy at 30°C were 55.7 ± 0.1, 59.7 ± 1.3, 71.7 ± 1.0, and 57.4 ± 0.3 mJ/m2. MCC samples are agglomerates of small individual cellulose particles. The different particle sizes and morphologies of the three MCC samples resulted in various hydroxyl numbers, which in turn affected their dispersion component of surface energy. Cellulose samples exhibiting a higher hydroxyl number have a higher dispersion component of surface energy. The dispersion component of surface energy of all the cellulose samples decreased linearly with increasing temperature. MCC samples with larger agglomerates had a lower temperature coefficient of dispersion component of surface energy.

Production of Asbestos-free Brake Pad Using Groundnut Shell as Filler Material

2018 ◽  
Vol 4 (12) ◽  
Author(s):  
W. C. Solomon ◽  
M. T. Lilly ◽  
J. I. Sodiki
Keyword(s):  
Phenolic Resin ◽  
Cost Effective ◽  
Filler Material ◽  
Particle Sizes ◽  
Brake Pad ◽  
Brake Pads ◽  
Environmental Friendly ◽  
Sieve Size ◽  
Groundnut Shell ◽  
The Cost

The development and evaluation of brake pads using groundnut shell (GS) particles as substitute material for asbestos were carried out in this study. This was with a view to harnessing the properties of GS, which is largely deposited as waste, and in replacing asbestos which is carcinogenic in nature despite its good tribological and mechanical properties. Two sets of composite material were developed using varying particle sizes of GS as filler material, with phenolic resin as binder with percentage compositions of 45% and 50% respectively. Results obtained indicate that the compressive strength and density increase as the sieve size of the filler material decreases, while water and oil absorption rates increase with an increase in sieve size of GS particle. This study also indicates that the cost of producing brake pad can be reduced by 19.14 percent if GS is use as filler material in producing brake pad. The results when compared with those of asbestos and industrial waste showed that GS particle can be used as an effective replacement for asbestos in producing automobile brake pad. Unlike asbestos, GS-based brake pads are environmental friendly, biodegradable and cost effective.

Effects of particle sizes, wood to cement ratio and chemical additives on the properties of sesendok (Endospermum Diadenum) cement-bonded particleboard

2010 ◽  
Vol 7 (2) ◽  
pp. 57
Author(s):  
Jamaludin Kasim ◽  
Shaikh Abdul Karim Yamani ◽  
Ahmad Firdaus Mat Hedzir ◽  
Ahmad Syafiq Badrul Hisham ◽  
Mohd Arif Fikri Mohamad Adnan
Keyword(s):  
Mechanical Properties ◽  
Experimental Investigation ◽  
Cement Content ◽  
Particle Sizes ◽  
Thickness Swelling ◽  
Chemical Additives ◽  
Board Density ◽  
Cement Ratio ◽  
Aluminium Silicate ◽  
Cement Board

An experimental investigation was performed to evaluate the properties of cement-bonded particleboard made from Sesendok wood. The target board density was set at a standard 1200 kg m". The effect offarticle size, wood to cement ratio and the addition ofsodium silicate and aluminium silicate on the wood cement board properties has been evaluated. A change ofparticle size from 1.0 mm to 2.0 mm has a significant effect on the mechanical properties, however the physical properties deteriorate. Increasing the wood to cement ratio from 1:2.25 to 1:3 decreases the modulus ofrupture (MOR) by 11% and the addition ofsodium silicate improves valuesfurther by about 28% compared to the addition ofaluminum silicate. The modulus ofelasticity (MOE) in general increases with increasing cement content, but is not significantly affected by the addition ofsodium silicate or aluminium silicate, although the addition of their mixture (sodium silicate andaluminium silicate) consistentlyyields greater MOE values. Water absorption and thickness swelling is significantly affected by the inclusion ofadditives and better values are attained using higher wood to cement ratios.

Revisiting Glycerol Esterification with Acetic Acid over Amberlyst-35 via Statistically Designed Experiments: Overcoming Transport Limitations

2019 ◽  
Author(s):  
Víctor Gabriel Baldovino Medrano ◽  
Karen V. Caballero ◽  
Hernando Guerrero-Amaya
Keyword(s):  
Acetic Acid ◽  
Active Sites ◽  
Batch Reactor ◽  
Catalyst Particle ◽  
Experimental Designs ◽  
Particle Sizes ◽  
Turnover Rates ◽  
Designed Experiments ◽  
Different Temperatures ◽  
Glycerol Esterification

Turnover rates for glycerol esterification with acetic acid over Amberlyst-35 were measured under different temperatures, reactants and active sites concentrations, and catalyst particle sizes. Data were collected in a batch reactor. Experiments were done following a sequence of factorial experimental designs.

Sign in / Sign up

Export Citation Format

Share Document