A mathematical analysis of the steady response of floating ice to the uniform motion of a rectangular load

1995 ◽  
Vol 287 ◽  
pp. 173-197 ◽  
Author(s):  
F. Milinazzo ◽  
Marvin Shinbrot ◽  
N. W. Evans
Keyword(s):  
Aspect Ratio ◽  
Good Description ◽  
Ice Sheet ◽  
Phase Speed ◽  
Surface Displacement ◽  
Fourier Integral ◽  
Uniform Motion ◽  
Far Field ◽  
Line Load ◽  
Aspect Ratios

In this article, we considered the steady response of an infinite unbroken floating ice sheet to the uniform motion of a rectangular load. It is assumed that the ice sheet is supported below by water of finite uniform depth. The ice displacement is expressed as a Fourier integral and the method of residues is combined with a numerical quadrature scheme to calculate the displacement of the surface. In addition, asymptotic estimates of the displacement are given for the far field and for the case where the aspect ratio of the load is large. The far-field approximation provides a good description of the surface displacement at distances greater than about one or two wavelengths away from the load. The behaviour of the steady solution at the two critical speeds Um, where the phase speed takes on its minimum, and Ug, the speed of gravity waves on shallow water, observed in Schulkes & Sneyd (1988) for an impulsively started line load is examined to see if these speeds are critical for two-dimensional loads. Unlike the steady part of the solution in Schulkes & Sneyd (1988), the solution is everywhere finite at the critical speed Ug. However, at the load speed Um, the solution is unbounded. At all load speeds the change in surface displacement is greatest near the load. A comparison with the experimental observations of Takizawa (1985) is made. Our calculations show a significant dependence of the amplitude of the ice displacement on the aspect ratio of the load. For wide loads the surface deflection has much more structure than does the surface displacement corresponding to loads of smaller aspect ratios.

scholarly journals Indentation of an S2 Floating Ice Sheet in the Brittle Range

1983 ◽  
Vol 4 ◽  
pp. 180-187 ◽  
Author(s):  
B. Michel ◽  
D. Blanchet
Keyword(s):  
Aspect Ratio ◽  
Research Work ◽  
Ice Sheets ◽  
Ice Sheet ◽  
Theory Of Elasticity ◽  
Maximum Pressure ◽  
Shear Cracks ◽  
Aspect Ratios ◽  
Two Parameters ◽  
The Impact

The problem of a floating ice sheet hitting a structure with a vertical face appears to be a simple one but, in fact, has only been solved for a limited number of cases. Research work on this question usually reports on an indentation coefficient which relates the average pressure on the indenter to the uniaxial crushing strength of the ice. Very few tests have been made in the brittle range of ice failure. In this particular area of study, this paper reports on 27 tests that were conducted in a cold-room water basin where controlled S2floating ice sheets were produced with a surface area of 4 × 4 m, three sides being fully restrained and the other, freely float! no, being submitted to the impact of the moving indenter. All tests were carried out at computed indentation rates varying from 0.017 to 0.34 s-1. In this range this ice would normally be considered to act as a brittle material. The thickness of the ice sheets varied from 1.2 to 9.0 cm and the indenter width from 5 cm to 1 m. Overall, the aspect ratio relating these two parameters could be varied from 0.5 to 83.Results have shown that for aspect ratios <5, there was an important oscillatory effect which caused the formation of pi asti fi ed triangles in front of the indenter, increasing its resistance as it would under ductile conditions. Because of this plastification, an extrusion effect appeared in front of the indenter as the broken ice crystals were blown up and down in front of the fast-moving indenter. The theory of plasticity which gives an indentation coefficient of 2.97 seems to apply in this case. Another mode of failure which occurred with aspect ratios 5 was cleavage in the plane of the ice sheet which also gives a higher indentation coefficient for S2ice, but of the same order of magnitude as previously.For intermediate values of the aspect ratio, between 5 and 20, the theory of elasticity used by Michel (1978) seems to apply well. Shear cracks are first formed on both sides of the square indenter and control the maximum pressure when they propagate inside forming big triangles in front of it.Finally, for aspect ratios ~>20, buckling of the ice occurs, either after or at the same time as the formation of wedges, together with a reduction in the indentation coefficient to a value close to that given by the theory of buckling of a truncated 45° wedge with a hinged edge.

scholarly journals Indentation of an S2 Floating Ice Sheet in the Brittle Range

1983 ◽  
Vol 4 ◽  
pp. 180-187 ◽  
Author(s):  
B. Michel ◽  
D. Blanchet
Keyword(s):  
Aspect Ratio ◽  
Research Work ◽  
Ice Sheets ◽  
Ice Sheet ◽  
Theory Of Elasticity ◽  
Maximum Pressure ◽  
Shear Cracks ◽  
Aspect Ratios ◽  
Two Parameters ◽  
The Impact

The problem of a floating ice sheet hitting a structure with a vertical face appears to be a simple one but, in fact, has only been solved for a limited number of cases. Research work on this question usually reports on an indentation coefficient which relates the average pressure on the indenter to the uniaxial crushing strength of the ice. Very few tests have been made in the brittle range of ice failure. In this particular area of study, this paper reports on 27 tests that were conducted in a cold-room water basin where controlled S2 floating ice sheets were produced with a surface area of 4 × 4 m, three sides being fully restrained and the other, freely float! no, being submitted to the impact of the moving indenter. All tests were carried out at computed indentation rates varying from 0.017 to 0.34 s-1. In this range this ice would normally be considered to act as a brittle material. The thickness of the ice sheets varied from 1.2 to 9.0 cm and the indenter width from 5 cm to 1 m. Overall, the aspect ratio relating these two parameters could be varied from 0.5 to 83.Results have shown that for aspect ratios <5, there was an important oscillatory effect which caused the formation of pi asti fi ed triangles in front of the indenter, increasing its resistance as it would under ductile conditions. Because of this plastification, an extrusion effect appeared in front of the indenter as the broken ice crystals were blown up and down in front of the fast-moving indenter. The theory of plasticity which gives an indentation coefficient of 2.97 seems to apply in this case. Another mode of failure which occurred with aspect ratios 5 was cleavage in the plane of the ice sheet which also gives a higher indentation coefficient for S2 ice, but of the same order of magnitude as previously.For intermediate values of the aspect ratio, between 5 and 20, the theory of elasticity used by Michel (1978) seems to apply well. Shear cracks are first formed on both sides of the square indenter and control the maximum pressure when they propagate inside forming big triangles in front of it.Finally, for aspect ratios ~>20, buckling of the ice occurs, either after or at the same time as the formation of wedges, together with a reduction in the indentation coefficient to a value close to that given by the theory of buckling of a truncated 45° wedge with a hinged edge.

Nonlinear effects in the response of a floating ice plate to a moving load

2002 ◽  
Vol 460 ◽  
pp. 281-305 ◽  
Author(s):  
EMILIAN PĂRĂU ◽  
FREDERIC DIAS
Keyword(s):  
Shallow Water ◽  
Deep Water ◽  
Critical Speed ◽  
Moving Load ◽  
Ice Sheet ◽  
Phase Speed ◽  
Nonlinear Effects ◽  
Line Load ◽  
Weakly Nonlinear ◽  
Water Depths

The steady response of an infinite unbroken floating ice sheet to a moving load is considered. It is assumed that the ice sheet is supported below by water of finite uniform depth. For a concentrated line load, earlier studies based on the linearization of the problem have shown that there are two ‘critical’ load speeds near which the steady deflection is unbounded. These two speeds are the speed c0 of gravity waves on shallow water and the minimum phase speed cmin. Since deflections cannot become infinite as the load speed approaches a critical speed, Nevel (1970) suggested nonlinear effects, dissipation or inhomogeneity of the ice, as possible explanations. The present study is restricted to the effects of nonlinearity when the load speed is close to cmin. A weakly nonlinear analysis, based on dynamical systems theory and on normal forms, is performed. The difference between the critical speed cmin and the load speed U is taken as the bifurcation parameter. The resulting normal form reduces at leading order to a forced nonlinear Schrödinger equation, which can be integrated exactly. It is shown that the water depth plays a role in the effects of nonlinearity. For large enough water depths, ice deflections in the form of solitary waves exist for all speeds up to (and including) cmin. For small enough water depths, steady bounded deflections exist only for speeds up to U*, with U* < cmin. The weakly nonlinear results are validated by comparison with numerical results based on the full governing equations. The model is validated by comparison with experimental results in Antarctica (deep water) and in a lake in Japan (relatively shallow water). Finally, nonlinear effects are compared with dissipation effects. Our main conclusion is that nonlinear effects play a role in the response of a floating ice plate to a load moving at a speed slightly smaller than cmin. In deep water, they are a possible explanation for the persistence of bounded ice deflections for load speeds up to cmin. In shallow water, there seems to be an apparent contradiction, since bounded ice deflections have been observed for speeds up to cmin while the theoretical results predict bounded ice deflection only for speeds up to U* < cmin. But in practice the value of U* is so close to the value of cmin that it is difficult to distinguish between these two values.

scholarly journals Effects of Steel Fiber Percentage and Aspect Ratios on Fresh and Harden Properties of Ultra-High Performance Fiber

2021 ◽  
Vol 2 (3) ◽  
pp. 501-515
Author(s):  
Rajib Kumar Biswas ◽  
Farabi Bin Ahmed ◽  
Md. Ehsanul Haque ◽  
Afra Anam Provasha ◽  
Zahid Hasan ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Aspect Ratio ◽  
High Performance ◽  
Steel Fiber ◽  
Setting Time ◽  
Fiber Reinforced Concrete ◽  
Future Research ◽  
Manufacturing Cost ◽  
Aspect Ratios ◽  
High Performance Fiber

Steel fibers and their aspect ratios are important parameters that have significant influence on the mechanical properties of ultrahigh-performance fiber-reinforced concrete (UHPFRC). Steel fiber dosage also significantly contributes to the initial manufacturing cost of UHPFRC. This study presents a comprehensive literature review of the effects of steel fiber percentages and aspect ratios on the setting time, workability, and mechanical properties of UHPFRC. It was evident that (1) an increase in steel fiber dosage and aspect ratio negatively impacted workability, owing to the interlocking between fibers; (2) compressive strength was positively influenced by the steel fiber dosage and aspect ratio; and (3) a faster loading rate significantly improved the mechanical properties. There were also some shortcomings in the measurement method for setting time. Lastly, this research highlights current issues for future research. The findings of the study are useful for practicing engineers to understand the distinctive characteristics of UHPFRC.

scholarly journals Surface Texturing of Si with Periodically Arrayed Oblique Nanopillars to Achieve Antireflection

Materials ◽  
2021 ◽  
Vol 14 (2) ◽  
pp. 380
Author(s):  
Jun-Hyun Kim ◽  
Sanghyun You ◽  
Chang-Koo Kim
Keyword(s):  
Aspect Ratio ◽  
Plasma Etching ◽  
Surface Texturing ◽  
Light Reflection ◽  
Si Substrate ◽  
Weighted Mean ◽  
Optical Reflectance ◽  
Si Substrates ◽  
Aspect Ratios ◽  
Shadowing Effect

Si surfaces were texturized with periodically arrayed oblique nanopillars using slanted plasma etching, and their optical reflectance was measured. The weighted mean reflectance (Rw) of the nanopillar-arrayed Si substrate decreased monotonically with increasing angles of the nanopillars. This may have resulted from the increase in the aspect ratio of the trenches between the nanopillars at oblique angles due to the shadowing effect. When the aspect ratios of the trenches between the nanopillars at 0° (vertical) and 40° (oblique) were equal, the Rw of the Si substrates arrayed with nanopillars at 40° was lower than that at 0°. This study suggests that surface texturing of Si with oblique nanopillars reduces light reflection compared to using a conventional array of vertical nanopillars.

scholarly journals Influence of Tsunami Aspect Ratio on Near and Far-Field Tsunami Amplitude

Geosciences ◽  
2021 ◽  
Vol 11 (4) ◽  
pp. 178
Author(s):  
Natalia K. Sannikova ◽  
Harvey Segur ◽  
Diego Arcas
Keyword(s):  
Aspect Ratio ◽  
Near Field ◽  
Decay Rates ◽  
Far Field ◽  
Present Evidence ◽  
Positive Wave ◽  
Initial Wave ◽  
N Wave ◽  
Tsunami Amplitude ◽  
Wave Shapes

This study presents a numerical investigation of the source aspect ratio (AR) influence on tsunami decay characteristics with an emphasis in near and far-field differences for two initial wave shapes Pure Positive Wave and N-wave. It is shown that, when initial total energy for both tsunami types is kept the same, short-rupture tsunami with more concentrated energy are likely to be more destructive in the near-field, whereas long rupture tsunami are more dangerous in the far-field. The more elongated the source is, the stronger the directivity and the slower the amplitude decays in the intermediate- and far-fields. We present evidence of this behavior by comparing amplitude decay rates from idealized sources and showing their correlation with that observed in recent historical events of similar AR.

scholarly journals Strength Analysis of Alternative Airframe Layouts of Regional Aircraft on the Basis of Automated Parametrical Models

Aerospace ◽  
2021 ◽  
Vol 8 (3) ◽  
pp. 80
Author(s):  
Dmitry V. Vedernikov ◽  
Alexander N. Shanygin ◽  
Yury S. Mirgorodsky ◽  
Mikhail D. Levchenkov
Keyword(s):  
Aspect Ratio ◽  
High Aspect Ratio ◽  
High Performance ◽  
Strength Analysis ◽  
Labor Input ◽  
Aerodynamic Loading ◽  
Aspect Ratios ◽  
Wide Range ◽  
Parametrical Design

This publication presents the results of complex parametrical strength investigations of typical wings for regional aircrafts obtained by means of the new version of the four-level algorithm (FLA) with the modified module responsible for the analysis of aerodynamic loading. This version of FLA, as well as a base one, is focused on significant decreasing time and labor input of a complex strength analysis of airframes by using simultaneously different principles of decomposition. The base version includes four-level decomposition of airframe and decomposition of strength tasks. The new one realizes additional decomposition of alternative variants of load cases during the process of determination of critical load cases. Such an algorithm is very suitable for strength analysis and designing airframes of regional aircrafts having a wide range of aerodynamic concepts. Results of validation of the new version of FLA for a high-aspect-ratio wing obtained in this work confirmed high performance of the algorithm in decreasing time and labor input of strength analysis of airframes at the preliminary stages of designing. During parametrical design investigation, some interesting results for strut-braced wings having high aspect ratios were obtained.

Influence of nozzle exit geometrical parameters on supersonic jet decay

2021 ◽  
Vol 0 (0) ◽  
Author(s):  
Prasanta Kumar Mohanta ◽  
B. T. N. Sridhar ◽  
R. K. Mishra
Keyword(s):  
Aspect Ratio ◽  
Nozzle Exit ◽  
Ambient Air ◽  
Schlieren Image ◽  
Geometrical Parameters ◽  
Image Study ◽  
Aspect Ratios ◽  
Core Length ◽  
Supersonic Core Length ◽  
The Impact

Abstract Experiments and simulations were carried on C-D nozzles with four different exit geometry aspect ratios to investigate the impact of supersonic decay characteristics. Rectangular and elliptical exit geometries were considered for the study with various aspect ratios. Numerical simulations and Schlieren image study were studied and found the agreeable logical physics of decay and spread characteristics. The supersonic core decay was found to be of different length for different exit geometry aspect ratio, though the throat to exit area ratio was kept constant to maintain the same exit Mach number. The impact of nozzle exit aspect ratio geometry was responsible to enhance the mixing of primary flow with ambient air, without requiring a secondary method to increase the mixing characteristics. The higher aspect ratio resulted in better mixing when compared to lower aspect ratio exit geometry, which led to reduction in supersonic core length. The behavior of core length reduction gives the identical signature for both under-expanded and over-expanded cases. The results revealed that higher aspect ratio of the exit geometry produced smaller supersonic core length. The aspect ratio of cross section in divergent section of the nozzle was maintained constant from throat to exit to reduce flow losses.

scholarly journals Aspect Ratio Driven Relationship between Nozzle Internal Flow and Supersonic Jet Mixing

Aerospace ◽  
2021 ◽  
Vol 8 (3) ◽  
pp. 78
Author(s):  
Kalyani Bhide ◽  
Kiran Siddappaji ◽  
Shaaban Abdallah
Keyword(s):  
Boundary Layer ◽  
Aspect Ratio ◽  
Nozzle Exit ◽  
Supersonic Jet ◽  
Internal Flow ◽  
Shear Stresses ◽  
Loss Mechanism ◽  
Potential Core ◽  
Jet Mixing ◽  
Aspect Ratios

This work attempts to connect internal flow to the exit flow and supersonic jet mixing in rectangular nozzles with low to high aspect ratios (AR). A series of low and high aspect ratio rectangular nozzles (design Mach number = 1.5) with sharp throats are numerically investigated using steady state Reynolds-averaged Navier−Stokes (RANS) computational fluid dynamics (CFD) with k-omega shear stress transport (SST) turbulence model. The numerical shadowgraph reveals stronger shocks at low ARs which become weaker with increasing AR due to less flow turning at the throat. Stronger shocks cause more aggressive gradients in the boundary layer resulting in higher wall shear stresses at the throat for low ARs. The boundary layer becomes thick at low ARs creating more aerodynamic blockage. The boundary layer exiting the nozzle transforms into a shear layer and grows thicker in the high AR nozzle with a smaller potential core length. The variation in the boundary layer growth on the minor and major axis is explained and its growth downstream the throat has a significant role in nozzle exit flow characteristics. The loss mechanism throughout the flow is shown as the entropy generated due to viscous dissipation and accounts for supersonic jet mixing. Axis switching phenomenon is also addressed by analyzing the streamwise vorticity fields at various locations downstream from the nozzle exit.

scholarly journals Atmospheric Ice Particle Shape Estimates from Polarimetric Radar Measurements and In Situ Observations

2017 ◽  
Vol 34 (12) ◽  
pp. 2569-2587 ◽  
Author(s):  
Sergey Y. Matrosov ◽  
Carl G. Schmitt ◽  
Maximilian Maahn ◽  
Gijs de Boer
Keyword(s):  
Aspect Ratio ◽  
Particle Shape ◽  
Characteristic Size ◽  
In Situ Measurements ◽  
Department Of Energy ◽  
Depolarization Ratio ◽  
Suggested Approach ◽  
Aspect Ratios ◽  
Radar Measurements

AbstractA remote sensing approach to retrieve the degree of nonsphericity of ice hydrometeors using scanning polarimetric Ka-band radar measurements from a U.S. Department of Energy Atmospheric Radiation Measurement (ARM) Program cloud radar operated in an alternate transmission–simultaneous reception mode is introduced. Nonsphericity is characterized by aspect ratios representing the ratios of particle minor-to-major dimensions. The approach is based on the use of a circular depolarization ratio (CDR) proxy reconstructed from differential reflectivity ZDR and copolar correlation coefficient ρhυ linear polarization measurements. Essentially combining information contained in ZDR and ρhυ, CDR-based retrievals of aspect ratios are fairly insensitive to hydrometeor orientation if measurements are performed at elevation angles of around 40°–50°. The suggested approach is applied to data collected using the third ARM Mobile Facility (AMF3), deployed to Oliktok Point, Alaska. Aspect ratio retrievals were also performed using ZDR measurements that are more strongly (compared to CDR) influenced by hydrometeor orientation. The results of radar-based retrievals are compared with in situ measurements from the tethered balloon system (TBS)-based video ice particle sampler and the ground-based multiangle snowflake camera. The observed ice hydrometeors were predominantly irregular-shaped ice crystals and aggregates, with aspect ratios varying between approximately 0.3 and 0.8. The retrievals assume that particle bulk density influencing (besides the particle shape) observed polarimetric variables can be deduced from the estimates of particle characteristic size. Uncertainties of CDR-based aspect ratio retrievals are estimated at about 0.1–0.15. Given these uncertainties, radar-based retrievals generally agreed with in situ measurements. The advantages of using the CDR proxy compared to the linear depolarization ratio are discussed.

Sign in / Sign up

Export Citation Format

Share Document