Influence of Heat Treatments on Microstructures in an Fe-Co-V Alloy

1974 ◽  
Vol 32 ◽  
pp. 512-513
Author(s):  
S. Mahajan ◽  
M. R. Pinnel ◽  
J. E. Bennett
Keyword(s):  
Single Phase ◽  
Alloy Composition ◽  
Supersaturated Solid Solution ◽  
Cell Formation ◽  
Heat Treatments ◽  
Air Cooling ◽  
Iced Brine ◽  
Transmission Electron ◽  
The Matrix ◽  
Bcc Structure

The microstructural changes in an Fe-Co-V alloy (composition by wt.%: 2.97 V, 48.70 Co, 47.34 Fe and balance impurities, such as C, P and Ni) resulting from different heat treatments have been evaluated by optical metallography and transmission electron microscopy. Results indicate that, on air cooling or quenching into iced-brine from the high temperature single phase ϒ (fcc) field, vanadium can be retained in a supersaturated solid solution (α2) which has bcc structure. For the range of cooling rates employed, a portion of the material appears to undergo the γ-α2 transformation massively and the remainder martensitically. Figure 1 shows dislocation topology in a region that may have transformed martensitically. Dislocations are homogeneously distributed throughout the matrix, and there is no evidence for cell formation. The majority of the dislocations project along the projections of <111> vectors onto the (111) plane, implying that they are predominantly of screw character.

The Effect of Deposition and Annealing Conditions on the Microstructure of Al-Cu and Al-Cu-Si Thin Films

1991 ◽  
Vol 229 ◽  
Author(s):  
M. Park ◽  
S. J. Krause ◽  
S. R. Wilson
Keyword(s):  
Single Phase ◽  
Alloy Composition ◽  
Phase Region ◽  
Annealed Condition ◽  
Two Phase ◽  
Annealing Conditions ◽  
Transmission Electron ◽  
Sputter Deposited ◽  
Cu Thin Film

AbstractThe effect of deposition temperature and the addition of Si to sputter deposited Al-Cu thin-film microstructure was studied with transmission electron microscopy. Films were studied in the as-deposited and annealed condition. The effects of thermal treatment were studied with in-situ hot stage microscopy. Al2Cu (θ) precipitated at the grain boundaries and the sublayer interface. At higher deposition temperatures, with alloy composition in single phase region (Al-1.5 wt.%Cu), Al2Cu precipitated during cooldown. At lower temperatures, in the two phase Al-0 region, Al2Cu precipitated during deposition. The addition of Si caused formation of Si precipitates and retarded Al2Cu precipitation during deposition or cooldown.

The Microscopic Study of Y-Ba-Cu-O Compound

1987 ◽  
Vol 99 ◽  
Author(s):  
W. T. Lin ◽  
H. C. Chu ◽  
B. H. Chen ◽  
Y. H. Chang ◽  
T. S. Chin ◽  
...  
Keyword(s):  
Electron Microscope ◽  
Orientation Relationship ◽  
Microscopic Study ◽  
Transmission Electron Microscope ◽  
Air Cooling ◽  
Twin Boundaries ◽  
Major Phase ◽  
Transmission Electron ◽  
The Matrix

ABSTRACTThe microstructure of Y-Ba-Cu-O compound, sintered at 950°C for 16h, was examined by using transmission electron microscope(TEM). For the furnace cooling sample, two variants of–orthorhombic YBa2-Cu3O7−x (O-Y123) twins, grown on (110) and (110) planes, respectively, are crystallographically related to the matrix and produce a Widmanstatten morphology. The orientation relationship between the lath twin and the matrix is (001)T//(001) and [100]T//[010]M. The O-Y123 compound is unstable under tne electron irradition. Twin boundaries are identified as S-boundaries. The minor phases as Y2BaCuO5 (Y211) and BaCuO2 were also observed. For the air cooling sample, no superconductivity above 77K was found. The major phase is tetragonal Y123 (T-Y123), while small amount of 0-Y123 is also existent.

Effect of Heat Treatment on the Microstructure of Cu-Cr-Zr Alloy

2017 ◽  
Vol 727 ◽  
pp. 166-170 ◽  
Author(s):  
Li Jun Peng ◽  
Hao Feng Xie ◽  
Gao Lei Xu ◽  
Guo Jie Huang ◽  
Zhen Yang
Keyword(s):  
Electron Microscope ◽  
Transmission Electron Microscope ◽  
Volume Fraction ◽  
Homogenization Temperature ◽  
Eutectic Structure ◽  
Optical Microscope ◽  
Heat Treatments ◽  
Transmission Electron ◽  
The Matrix ◽  
Zr Alloy

Effect of Heat treatments on microstructure in a Cu-0.71Cr-0.12Zr alloy (in wt.%) have been investigated. The microstructures are analyzed by optical microscope, scanning electron microscope, transmission electron microscope and high-resolution transmission electron microscope after each step of heat treatments. The results show that the as-cast microstructure of Cu-Cr-Zr alloy is Cu matrix, Cr dendrite and eutectic structure which is composed of Cu and Cu5Zr phase with a fine lamellar structure. By increasing the homogenization temperature or prolonging the holding time, the eutectic structure is dissolved into the matrix gradually and the volume fraction of the Cr phases is obviously reduced. The precipitation of Cr phase prevents from Zr-rich phases dissolving in the matrix. And the proper homogenizing process is 900°C×12 h. When the alloy aged at 450°C for 24 h, the crystallography of Cr precipitates and the orientation relationship between Cr precipitates and Cu matrix is bcc structure and KS-OR, respectively. The disk-shaped precipitate is identified as Cu5Zr phase and their habit plane is parallel to {111}Cu plane.

TEM Investigations of Electron 21 Magnesium Alloy

2007 ◽  
Vol 130 ◽  
pp. 175-180 ◽  
Author(s):  
Andrzej Kiełbus
Keyword(s):  
Heat Treatment ◽  
Magnesium Alloy ◽  
Solution Heat Treatment ◽  
Cast Alloy ◽  
Solution Treatment ◽  
Air Cooling ◽  
Transmission Electron ◽  
The Matrix ◽  
Cast Condition ◽  
Cast Microstructure

The paper presents results of TEM investigations of Elektron 21 magnesium alloy in as cast condition and after heat treatment. The compositions of the Elektron 21 alloy used in the present study was Mg-2,7%wtNd-1,2%wtGd-0,47%wtZr. Solution heat treatment was performed at 520°C/8 h/water. Ageing treatments were performed at 200°C/4÷96h and 300°C/48h with cooling in air. The as-cast microstructure and microstructural evolution during heat treatment were examined by transmission electron microscopy. Samples were prepared using Gatan PIPS ion mill. Examinations were performed in a JEM 2010 ARP microscope. The microstructure of the cast alloy consists of a-Mg phase matrix with precipitates of Mg12(Ndx,Gd1-x) phase at grain boundaries. After solution treatment the Mg12(Ndx,Gd1-x) phase dissolved in the matrix. The ageing treatment applied after solution treatment with air-cooling caused precipitation of a β’ and β phases.

scholarly journals Relationship between Microstructure and Properties of Cu–Cr–Ag Alloy

Materials ◽  
2020 ◽  
Vol 13 (3) ◽  
pp. 732
Author(s):  
Dong Liang ◽  
Xujun Mi ◽  
Lijun Peng ◽  
Haofeng Xie ◽  
Guojie Huang ◽  
...  
Keyword(s):  
Electron Microscope ◽  
Cold Deformation ◽  
Solution Treatment ◽  
Aging Treatment ◽  
Face Centered Cubic ◽  
Transmission Electron ◽  
The Matrix ◽  
Bcc Structure ◽  
Continuous Extrusion ◽  
Face Centered

The microstructure evolution and properties of a Cu–Cr–Ag alloy during continuous extrusion and an aging process were studied by Scanning Electron Microscope (SEM) and Transmission Electron Microscope (TEM). Owing to strong shear deformation that happened during continuous extrusion with working temperatures of 450 to 480 °C, a larger number of fine grains were obtained. Both face-centered cubic (FCC) and body-centered cubic (BCC) precipitates simultaneously existed in the matrix when aged for 450 °C for 2 h, and the Cr phases with BCC structure had an N–W relationship with the matrix. After continuous extrusion, 60% cold deformation, 875 °C × 1 h solid solution treatment, 60% cold deformation, 450 °C × 2 h aging treatment, and 70% cold deformation, the Cu–Cr–Ag alloy acquired excellent comprehensive properties: tensile strength of 494.4 MPa, yield strength of 487.6 MPa, and electrical conductivity of 91.4% IACS.

scholarly journals Effects of C Addition on the Microstructures of As-Cast Cu–Fe–P Alloys

Materials ◽  
2019 ◽  
Vol 12 (17) ◽  
pp. 2772 ◽  
Author(s):  
Chen ◽  
Hu ◽  
Guo ◽  
Zou ◽  
Liu ◽  
...  
Keyword(s):  
Orientation Relationship ◽  
Supersaturated Solid Solution ◽  
Face Centered Cubic ◽  
Body Centered Cubic ◽  
Matrix Microstructure ◽  
The Matrix ◽  
Bcc Structure ◽  
The Difference ◽  
Face Centered ◽  
Fcc Structure

Effects of C addition on the microstructures of as-cast Cu–Fe–P (mass fraction) alloys were systematically investigated. The results show that C addition can refine the matrix microstructure and make Fe particles finer. The Fe particles observed in both the non-C-alloyed and C-alloyed specimens are α-Fe particles, which possess a body-centered cubic (bcc) structure with a Nishiyama–Wassermann orientation relationship with the matrix. C is reported to be an γ-Fe stabilizer in the literature. The reason for the difference between the phases of Fe particles observed in this study, and that reported in the literature, are finally discussed. Additionally, C addition facilitates the decomposition of the supersaturated solid solution which occurs by the simultaneous precipitation of very fine Fe particles. Such initial decomposition product has an face-centered cubic (fcc) structure with a cube-on-cube orientation relationship with the matrix.

Decomposition of a Biocompatible Zr-Ta-Nb Alloy

2007 ◽  
Vol 561-565 ◽  
pp. 1525-1528 ◽  
Author(s):  
Wei Sun
Keyword(s):  
Electron Microscopy ◽  
High Resolution Electron Microscopy ◽  
Heat Treatments ◽  
Electron Probe Analysis ◽  
Β Phase ◽  
Α Phase ◽  
Transmission Electron ◽  
Resolution Electron ◽  
Bcc Structure ◽  
Highly Strained

A Zr-Ta-Nb alloy made of biocompatible alloy elements only and consisted of single β-phase with bcc structure was prepared by conventional solidification. Electron diffraction, transmission electron microscopy (TEM) and high-resolution electron microscopy (HREM) were used to examine microstructural evolutions of the β-Zr-Ta-Nb alloy subjected to different heat treatments. The results show that the metastable β-phase in the as-solidified Zr-Ta-Nb alloy turned to decompose when annealed at 400°C and this led to the formation of a highly strained structure containing nanosized precipitates and local disordered regions. Striking phase separation including the formation of the equilibrium α-phase was found to occur at 600°C. By means of nanosized electron-probe analysis of energy dispersive X-ray spectroscopy, the compositions for the nanosized phases formed due to different heat treatments were analysis.

Determination of the phase structure of polymerblends by electron microscopy

1978 ◽  
Vol 36 (1) ◽  
pp. 492-493
Author(s):  
Dr. G. Kaemof
Keyword(s):  
Screw Extruder ◽  
Electron Microscopic ◽  
Thin Sections ◽  
Single Screw Extruder ◽  
Transmission Electron ◽  
The Matrix ◽  
Twin Screw ◽  
Special Case ◽  
Microscopic Investigations

A mixture of polycarbonate (PC) and styrene-acrylonitrile-copolymer (SAN) represents a very good example for the efficiency of electron microscopic investigations concerning the determination of optimum production procedures for high grade product properties.The following parameters have been varied:components of charge (PC : SAN 50 : 50, 60 : 40, 70 : 30), kind of compounding machine (single screw extruder, twin screw extruder, discontinuous kneader), mass-temperature (lowest and highest possible temperature).The transmission electron microscopic investigations (TEM) were carried out on ultra thin sections, the PC-phase of which was selectively etched by triethylamine.The phase transition (matrix to disperse phase) does not occur - as might be expected - at a PC to SAN ratio of 50 : 50, but at a ratio of 65 : 35. Our results show that the matrix is preferably formed by the components with the lower melting viscosity (in this special case SAN), even at concentrations of less than 50 %.

The microstructure of a TiB2/Ti-47 Al composite material

1989 ◽  
Vol 47 ◽  
pp. 674-675
Author(s):  
O. Popoola ◽  
A.H. Heuer ◽  
P. Pirouz
Keyword(s):  
Composite Material ◽  
Ion Beam ◽  
Chemical Properties ◽  
Intermetallic Alloys ◽  
Transmission Electron ◽  
Diamond Polishing ◽  
Al Composite ◽  
The Matrix ◽  
Argon Ion ◽  
And Chemical Properties

The addition of fibres or particles (TiB2, SiC etc.) into TiAl intermetallic alloys could increase their toughness without compromising their good high temperature mechanical and chemical properties. This paper briefly discribes the microstructure developed by a TiAl/TiB2 composite material fabricated with the XD™ process and forged at 960°C.The specimens for transmission electron microscopy (TEM) were prepared in the usual way (i.e. diamond polishing and argon ion beam thinning) and examined on a JEOL 4000EX for microstucture and on a Philips 400T equipped with a SiLi detector for microanalyses.The matrix was predominantly γ (TiAl with L10 structure) and α2(TisAl with DO 19 structure) phases with various morphologies shown in figure 1.

scholarly journals Evidence of Martensitic Transformation in Fe-Mn-Al Steel Similar to Maraging Steel

2020 ◽  
Vol 52 (1) ◽  
pp. 26-33
Author(s):  
Gurumayum Robert Kenedy ◽  
Yi-Jyun Lin ◽  
Wei-Chun Cheng
Keyword(s):  
Martensitic Transformation ◽  
Maraging Steel ◽  
Trip Steel ◽  
Single Phase ◽  
Lath Martensite ◽  
Al Alloy ◽  
Air Cooling ◽  
Small Temperature Gradient ◽  
Austenite Grains ◽  
Equilibrium Phases

AbstractThe Fe-Mn-Al steels claim a low density, and some fall into the category of transformation-induced plasticity (TRIP) steel. In Fe-Mn-Al TRIP steel development, phase transformations play an important role. Herein, the martensitic transformation of an Fe-16.7 Mn-3.4 Al ternary alloy (wt pct) was experimentally discovered, whose equilibrium phases are a single phase of austenite at 1373 K and dual phases of ferrite and austenite at low temperature. Ferritic lath martensite forms in the prior austenite grains after cooling from 1373 K under various cooling rates via quenching, air cooling, and furnace cooling. The formation mechanism of the ferritic lath martensite is different from that of traditional ferritic lath martensite in steel and quite similar to that in maraging steel. A slight strain energy coupled with a small temperature gradient can lead to the formation of ferritic lath martensite in the Fe-Mn-Al alloy after cooling from high temperature. It is also found that micro-twins exist in the ferritic lath martensite.

Sign in / Sign up

Export Citation Format

Share Document