Low-Loss Images in a Stem/Tem Microscope

1976 ◽  
Vol 34 ◽  
pp. 496-497 ◽  
Author(s):  
David C. Joy ◽  
Dennis M. Maher
Keyword(s):  
High Resolution ◽  
Surface Topography ◽  
Beam Direction ◽  
Low Loss ◽  
Specimen Holder ◽  
Glancing Angle ◽  
High Resolution Images ◽  
Set Up ◽  
Conventional Manner ◽  
Objective Type

High-resolution images of the surface topography of solid specimens can be obtained using the low-loss technique of Wells. If the specimen is placed inside a lens of the condenser/objective type, then it has been shown that the lens itself can be used to collect and filter the low-loss electrons. Since the probeforming lenses in TEM instruments fitted with scanning attachments are of this type, low-loss imaging should be possible.High-resolution, low-loss images have been obtained in a JEOL JEM 100B fitted with a scanning attachment and a thermal, fieldemission gun. No modifications were made to the instrument, but a wedge-shaped, specimen holder was made to fit the side-entry, goniometer stage. Thus the specimen is oriented initially at a glancing angle of about 30° to the beam direction. The instrument is set up in the conventional manner for STEM operation with all the lenses, including the projector, excited.

High Resolution Low Loss Microscopy of Crystalline Surfaces

1980 ◽  
Vol 38 ◽  
pp. 162-163
Author(s):  
William Krakow ◽  
Alec N. Broers
Keyword(s):  
Electron Microscopy ◽  
High Resolution ◽  
Surface Topography ◽  
Secondary Electron ◽  
Objective Lens ◽  
Surface Imaging ◽  
Low Loss ◽  
Fine Grained ◽  
Scanning Electron ◽  
Crystalline Surfaces

Low-loss scanning electron microscopy can be used to investigate the surface topography of solid specimens and provides enhanced image contrast over secondary electron images. A high resolution-condenser objective lens has allowed the low-loss technique to resolve separations of Au nucleii of 50Å and smaller dimensions of 25Å in samples coated with a fine grained carbon-Au-palladium layer. An estimate of the surface topography of fine grained vapor deposited materials (20 - 100Å) and the surface topography of underlying single crystal Si in the 1000 - 2000Å range has also been investigated. Surface imaging has also been performed on single crystals using diffracted electrons scattered through 10−2 rad in a conventional TEM. However, severe tilting of the specimen is required which degrades the resolution 15 to 100 fold due to image forshortening.

FeXIV Line Emission Polarization of the July 11, 1991 Solar Corona

1994 ◽  
Vol 144 ◽  
pp. 541-547
Author(s):  
J. Sýkora ◽  
J. Rybák ◽  
P. Ambrož
Keyword(s):  
High Resolution ◽  
Solar Corona ◽  
Emission Line ◽  
Solar Eclipse ◽  
White Light ◽  
Preliminary Analysis ◽  
Line Emission ◽  
Total Solar Eclipse ◽  
Degree Of Polarization ◽  
High Resolution Images

AbstractHigh resolution images, obtained during July 11, 1991 total solar eclipse, allowed us to estimate the degree of solar corona polarization in the light of FeXIV 530.3 nm emission line and in the white light, as well. Very preliminary analysis reveals remarkable differences in the degree of polarization for both sets of data, particularly as for level of polarization and its distribution around the Sun’s limb.

A Liquid Nitrogen Cooled Stage for STEM

1974 ◽  
Vol 32 ◽  
pp. 444-445
Author(s):  
Louis T. Germinario
Keyword(s):  
Electron Microscope ◽  
High Resolution ◽  
Liquid Nitrogen ◽  
Room Temperature ◽  
Objective Lens ◽  
Thermal Drift ◽  
Specimen Holder ◽  
Resolution Capability ◽  
Focal Position

A liquid nitrogen stage has been developed for the JEOL JEM-100B electron microscope equipped with a scanning attachment. The design is a modification of the standard JEM-100B SEM specimen holder with specimen cooling to any temperatures In the range ~ 55°K to room temperature. Since the specimen plane is maintained at the ‘high resolution’ focal position of the objective lens and ‘bumping’ and thermal drift la minimized by supercooling the liquid nitrogen, the high resolution capability of the microscope is maintained (Fig.4).

Remarks on the application of backscattered electron imaging (BEI) to the scanning electron microscopy (SEM) of biological structures

1983 ◽  
Vol 41 ◽  
pp. 484-487
Author(s):  
Etienne de Harven
Keyword(s):  
High Resolution ◽  
Incident Beam ◽  
Spot Size ◽  
Primary Electron ◽  
Critical Point Drying ◽  
Cell Shapes ◽  
High Resolution Images ◽  
Backscattered Electron ◽  
Electron Imaging ◽  
Scanning Electron

Biological ultrastructures have been extensively studied with the scanning electron microscope (SEM) for the past 12 years mainly because this instrument offers accurate and reproducible high resolution images of cell shapes, provided the cells are dried in ways which will spare them the damage which would be caused by air drying. This can be achieved by several techniques among which the critical point drying technique of T. Anderson has been, by far, the most reproducibly successful. Many biologists, however, have been interpreting SEM micrographs in terms of an exclusive secondary electron imaging (SEI) process in which the resolution is primarily limited by the spot size of the primary incident beam. in fact, this is not the case since it appears that high resolution, even on uncoated samples, is probably compromised by the emission of secondary electrons of much more complex origin.When an incident primary electron beam interacts with the surface of most biological samples, a large percentage of the electrons penetrate below the surface of the exposed cells.

Field Emission SEM Equipped With Noise Compensator

1973 ◽  
Vol 31 ◽  
pp. 302-303
Author(s):  
S. Saito ◽  
H. Todokoro ◽  
S. Nomura ◽  
T. Komoda
Keyword(s):  
Electron Microscope ◽  
High Resolution ◽  
Scanning Electron Microscope ◽  
Field Emission ◽  
Low Contrast ◽  
Probe Current ◽  
High Resolution Images ◽  
Scanning Electron

Field emission scanning electron microscope (FESEM) features extremely high resolution images, and offers many valuable information. But, for a specimen which gives low contrast images, lateral stripes appear in images. These stripes are resulted from signal fluctuations caused by probe current noises. In order to obtain good images without stripes, the fluctuations should be less than 1%, especially for low contrast images. For this purpose, the authors realized a noise compensator, and applied this to the FESEM.Fig. 1 shows an outline of FESEM equipped with a noise compensator. Two apertures are provided gust under the field emission gun.

Effect of strain on ADF-STEM high-resolution images

1991 ◽  
Vol 49 ◽  
pp. 666-667
Author(s):  
M. Kelly ◽  
D.M. Bird
Keyword(s):  
High Resolution ◽  
Strong Influence ◽  
Intensity Variation ◽  
Dark Field ◽  
Atomic Resolution ◽  
Strain Fields ◽  
High Resolution Image ◽  
Annular Dark Field ◽  
High Resolution Images ◽  
Interesting Alternative

It is well known that strain fields can have a strong influence on the details of HREM images. This, for example, can cause problems in the analysis of edge-on interfaces between lattice mismatched materials. An interesting alternative to conventional HREM imaging has recently been advanced by Pennycook and co-workers where the intensity variation in the annular dark field (ADF) detector is monitored as a STEM probe is scanned across the specimen. It is believed that the observed atomic-resolution contrast is correlated with the intensity of the STEM probe at the atomic sites and the way in which this varies as the probe moves from cell to cell. As well as providing a directly interpretable high-resolution image, there are reasons for believing that ADF-STEM images may be less suseptible to strain than conventional HREM. This is because HREM images arise from the interference of several diffracted beams, each of which is governed by all the excited Bloch waves in the crystal.

Electron crystallographic determination of the 3-D structure of staurolite at atomic resolution

1991 ◽  
Vol 49 ◽  
pp. 540-541
Author(s):  
Kenneth H. Downing ◽  
Hu Meisheng ◽  
Hans-Rudolf Went ◽  
Michael A. O'Keefe
Keyword(s):  
High Resolution ◽  
Three Dimensional ◽  
High Resolution Electron Microscopy ◽  
Atomic Resolution ◽  
Dimensional Structure ◽  
Structure Information ◽  
Resolution Electron ◽  
Scattering Effects ◽  
High Resolution Images ◽  
Effects Of Radiation

With current advances in electron microscope design, high resolution electron microscopy has become routine, and point resolutions of better than 2Å have been obtained in images of many inorganic crystals. Although this resolution is sufficient to resolve interatomic spacings, interpretation generally requires comparison of experimental images with calculations. Since the images are two-dimensional representations of projections of the full three-dimensional structure, information is invariably lost in the overlapping images of atoms at various heights. The technique of electron crystallography, in which information from several views of a crystal is combined, has been developed to obtain three-dimensional information on proteins. The resolution in images of proteins is severely limited by effects of radiation damage. In principle, atomic-resolution, 3D reconstructions should be obtainable from specimens that are resistant to damage. The most serious problem would appear to be in obtaining high-resolution images from areas that are thin enough that dynamical scattering effects can be ignored.

Design of a new objective lens for an HB-501A STEM

1991 ◽  
Vol 49 ◽  
pp. 416-417
Author(s):  
Earl J. Kirkland ◽  
Robert J. Keyse
Keyword(s):  
High Resolution ◽  
Spherical Aberration ◽  
Scanning Transmission Electron Microscope ◽  
Dark Field ◽  
Objective Lens ◽  
Specimen Holder ◽  
Transmission Electron ◽  
Scanning Transmission ◽  
Annular Dark Field ◽  
High Resolution Microscopy

An ultra-high resolution pole piece with a coefficient of spherical aberration Cs=0.7mm. was previously designed for a Vacuum Generators HB-501A Scanning Transmission Electron Microscope (STEM). This lens was used to produce bright field (BF) and annular dark field (ADF) images of (111) silicon with a lattice spacing of 1.92 Å. In this microscope the specimen must be loaded into the lens through the top bore (or exit bore, electrons traveling from the bottom to the top). Thus the top bore must be rather large to accommodate the specimen holder. Unfortunately, a large bore is not ideal for producing low aberrations. The old lens was thus highly asymmetrical, with an upper bore of 8.0mm. Even with this large upper bore it has not been possible to produce a tilting stage, which hampers high resolution microscopy.

Principle and practice of high-resolution imaging with a field-emission TEM

1992 ◽  
Vol 50 (1) ◽  
pp. 138-139
Author(s):  
Max T. Otten ◽  
Wim M.J. Coene
Keyword(s):  
High Resolution ◽  
Field Emission ◽  
Incidence Angle ◽  
Temporal Coherence ◽  
Energy Spread ◽  
High Resolution Imaging ◽  
Major Improvement ◽  
High Resolution Images ◽  
Resolution Imaging

High-resolution imaging with a LaB6 instrument is limited by the spatial and temporal coherence, with little contrast remaining beyond the point resolution. A Field Emission Gun (FEG) reduces the incidence angle by a factor 5 to 10 and the energy spread by 2 to 3. Since the incidence angle is the dominant limitation for LaB6 the FEG provides a major improvement in contrast transfer, reducing the information limit to roughly one half of the point resolution. The strong improvement, predicted from high-resolution theory, can be seen readily in diffractograms (Fig. 1) and high-resolution images (Fig. 2). Even if the information in the image is limited deliberately to the point resolution by using an objective aperture, the improved contrast transfer close to the point resolution (Fig. 1) is already worthwhile.

Computer processing of high-resolution images of periodic specimens

1986 ◽  
Vol 44 ◽  
pp. 2-5
Author(s):  
W. Chiu ◽  
M.F. Schmid ◽  
T.-W. Jeng
Keyword(s):  
High Resolution ◽  
Fourier Transforms ◽  
Complex Structure ◽  
Distribution Functions ◽  
Multiple Image ◽  
Cryo Electron Microscopy ◽  
Structure Factors ◽  
Unit Cells ◽  
High Resolution Images ◽  
Phase Probability Distribution

Cryo-electron microscopy has been developed to the point where one can image thin protein crystals to 3.5 Å resolution. In our study of the crotoxin complex crystal, we can confirm this structural resolution from optical diffractograms of the low dose images. To retrieve high resolution phases from images, we have to include as many unit cells as possible in order to detect the weak signals in the Fourier transforms of the image. Hayward and Stroud proposed to superimpose multiple image areas by combining phase probability distribution functions for each reflection. The reliability of their phase determination was evaluated in terms of a crystallographic “figure of merit”. Grant and co-workers used a different procedure to enhance the signals from multiple image areas by vector summation of the complex structure factors in reciprocal space.

Sign in / Sign up

Export Citation Format

Share Document